Owner and operator manual P a r t N u m b e r : 3 - 9 0 0 8 - 0 0 1, R e v .
Daniel customer service Location Telephone number Fax number North America/Latin America +1.713.467.6000 +1.713.827.4805 Daniel Customer Service +1.713.827.6314 +1.713.827.6312 USA (toll free) +1.888.356.9001 +1.713.827.3380 Asia Pacific (Republic of Singapore) +65.6777.8211 +65.6777.0947.0743 Europe (Stirling Scotland, UK) +44 (0)1786.433400 +44 (0)1786.433401 Middle East Africa (Dubai, UAE) +971 4 8118100 +971 4 8865465 E-mail • Customer Service: tech.service@emersonprocess.
Signal words and symbols Pay special attention to the following signal words, safety alert symbols and statements: Safety alert symbol This is a safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Danger indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Important safety instructions Daniel Measurement and Control, Inc. (Daniel) designs, manufactures and tests products to function within specific conditions. Because these products are sophisticated technical instruments, it is important that the owner and operation personnel strictly adhere both to the information printed on the product and to all instructions provided in this manual prior to installation, operation, and maintenance.
Product Operation Personnel: • To prevent personal injury, personnel must follow all instructions of this manual prior to and during operation of the product. • Follow all warnings, cautions, and notices marked on, and supplied with, this product. • Verify that this is the correct instruction manual for your Daniel product. If this is not the correct documentation, contact Daniel at 1-713-827-6314. You may also download the correct manual from: http://www.daniel.
Notice THE CONTENTS OF THIS PUBLICATION ARE PRESENTED FOR INFORMATIONAL PURPOSES ONLY, AND WHILE EVERY EFFORT HAS BEEN MADE TO ENSURE THEIR ACCURACY, THEY ARE NOT TO BE CONSTRUED AS WARRANTIES OR GUARANTEES, EXPRESSED OR IMPLIED, REGARDING THE PRODUCTS OR SERVICES DESCRIBED HEREIN OR THEIR USE OR APPLICABILITY. ALL SALES ARE GOVERNED BY DANIEL'S TERMS AND CONDITIONS, WHICH ARE AVAILABLE UPON REQUEST. WE RESERVE THE RIGHT TO MODIFY OR IMPROVE THE DESIGNS OR SPECIFICATIONS OF SUCH PRODUCTS AT ANY TIME.
Warranty and Limitations 1. LIMITED WARRANTY: Subject to the limitations contained in Section 2 herein, Daniel Measurement & Control, Inc.
Owner and operator manual Table of Contents 3-9008-001 Rev M January 2015 Contents Daniel customer service Signal words and symbols Important safety instructions Notice Warranty and Limitations Section 1: Introduction 1.1 Purpose of this manual ................................................................................ 1 1.2 Description ................................................................................................. 1 1.2.1 Technical data ........................................
Table of Contents Owner and operator manual January 2015 3-9008-001 Rev M Section 4: Orifice plate installation and removal instructions 4.1 Plate change procedure ............................................................................. 49 4.2 Selecting an appropriate plate change procedure ......................................... 50 4.3 Orifice plate (13) change operation ............................................................. 52 Section 5: 4.3.1 “Quick change” procedure...............
Owner and operator manual 3-9008-001 Rev M List of Tables January 2015 List of Tables Table 1-1 Daniel Senior Orifice Fitting sizes 2” thru 8” 150-900 ......................................................... 8 Table 1-2 Daniel Senior Orifice Fittings sizes 2” thru 8” 1500 and 2” thru 6” 2500 ........................... 12 Table 1-3 Daniel Senior Orifice Fittings sizes 8” thru 12” 2500 .........................................................
List of Tables January 2015 xii Owner and operator manual 3-9008-001 Rev M List of Tables
Owner and operator manual 3-9008-001 Rev M List of Figures January 2015 List of Figures Figure 1-1 Daniel Senior Orifice Fitting - Flangenek option ............................................................ 2 Figure 1-2 Daniel Senior Orifice Fitting drawing 2”-8” 150-900...................................................... 7 Figure 1-3 Daniel Senior Orifice Fitting drawing sizes 2”-8” 1500 and 2” -6” 2500 .......................
List of Figures January 2015 xiv Owner and operator manual 3-9008-001 Rev M List of Figures
Owner and operator manual 3-9008-001 Rev M Section 1: Introduction January 2015 Section 1: Introduction 11 12 13 14 15 16 1.1 Purpose of this manual Daniel Measurement & Control Inc. designed this manual to guide owners and personnel in the installation, operation and maintenance of the DanielTM SeniorTM Orifice Fitting.
Section 1: Introduction January 2015 Owner and operator manual 3-9008-001 Rev M Figure 1-1 Daniel Senior Orifice Fitting - Flangenek option Therefore, using a Senior may eliminate the need for bypass piping, valves, and other fittings necessary with conventional orifice fitting installations. Maintenance technicians can replace and repair all parts of the Senior, including the slide valve assembly, without removing the Body (4) from the line (refer to Section 3: Maintenance).
Owner and operator manual 3-9008-001 Rev M Section 1: Introduction January 2015 Products bearing the “CE” mark are designed and manufactured in compliance with the European Union Pressure Equipment Directive (PED) 97/23/EC. Refer to the “Daniel Orifice Fittings Installation and Operating Instructions specific to the Pressure Equipment Directive”, Part Number 3-9008-002. Technical References (available on the Daniel website): Description • Upp, E.L.
Section 1: Introduction Owner and operator manual January 2015 1.2.1 3-9008-001 Rev M Technical data Follow all the safety and equipment limits recommended in 1.2.1 Technical data of this manual. It is the owner’s and/or purchaser’s responsibility to comply with these parameters. PERSONAL PROTECTION HAZARD Follow all parameters for the Senior Orifice Fitting indicated below. Failure to do so may result in injury or equipment damage.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M Components: • Maintenance interval: Exercise components monthly. Examine components during orifice plate changes or at least once a year. Replace components when worn or damaged. • Seal replacement: Examine seals and gaskets during orifice plate inspections or at least once a year. Replace when worn or damaged. • Fastener torque verification: Monthly (see Section 5.3 for size /ANSI Class values).
Section 1: Introduction Owner and operator manual January 2015 3-9008-001 Rev M Interface parameters: • Replacement parts: Use only replacement parts specified by Daniel. Unauthorized parts and procedures can affect this product’s performance and place the safe operation of your process at risk. • After market attachments: Use of pressure sensing equipment, drain valves and other accessories (e.g., needle valves, multi-port valves, transmitters, 3- pin recorders...etc.) are permissible.
Owner and operator manual Section 1: Introduction 3-9008-001 Rev M 1.3 Specifications 1.3.
Section 1: Introduction Owner and operator manual January 2015 3-9008-001 Rev M All Parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Senior body from the line. Table 1-1 Daniel Senior Orifice Fitting sizes 2” thru 8” 150-900 Number required Parts and materials 8 Item no.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M Table 1-1 Daniel Senior Orifice Fitting sizes 2” thru 8” 150-900 Number required Parts and materials Size Item no.
Section 1: Introduction Owner and operator manual January 2015 3-9008-001 Rev M Notes:Table 1-1 1. All Daniel Senior Orifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory directly. 2. Locations of Equalizer Valve (1), Bleeder Valve (10B), and Grease Gun (23) may differ from diagrams shown in this manual. 3. Slide Valve Lubricant: 0.38in (9.53mm) diameter by 1.5in (38.
Owner and operator manual Section 1: Introduction 3-9008-001 Rev M 1.3.
Section 1: Introduction Owner and operator manual January 2015 3-9008-001 Rev M All Parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Senior body from the line. Table 1-2 Daniel Senior Orifice Fittings sizes 2” thru 8” 1500 and 2” thru 6” 2500 Number required Parts and materials Item no.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M Table 1-2 Daniel Senior Orifice Fittings sizes 2” thru 8” 1500 and 2” thru 6” 2500 Number required Parts and materials Size Item no.
Section 1: Introduction Owner and operator manual January 2015 3-9008-001 Rev M Table 1-2 Daniel Senior Orifice Fittings sizes 2” thru 8” 1500 and 2” thru 6” 2500 Number required Parts and materials Size Item no.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M Notes:Table 1-2 1. All Daniel Senior Orifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory directly. 2. Locations of Equalizer Valve (1), Bleeder Valve (10B), and Grease Gun (23) may differ from diagrams shown in this manual. 3. Slide Valve Lubricant: 0.38in (9.53mm) diameter by 1.5in (38.
Section 1: Introduction January 2015 1.3.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M All parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Daniel Senior Orifice Fitting body from the line. Table 1-3 Daniel Senior Orifice Fittings sizes 8” thru 12” 2500 Number required Parts and materials Size Item no.
Section 1: Introduction Owner and operator manual January 2015 3-9008-001 Rev M Table 1-3 Daniel Senior Orifice Fittings sizes 8” thru 12” 2500 Number required Parts and materials Size Item no.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M Notes:Table 1-3 1. All Daniel Senior Orifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory directly. 2. Locations of Equalizer Valve (1), Bleeder Valve (10B), and Grease Gun (23) may differ from diagrams shown in this manual. 3. Slide Valve Lubricant: 0.38in (9.53mm) diameter by 1.5in (38.
Section 1: Introduction January 2015 1.3.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M All Parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Daniel Senior Orifice Fitting body from the line. Table 1-4 Daniel Senior Orifice Fitting sizes 10” thru 16” 150-900 Number required Parts and materials Item no.
Section 1: Introduction Owner and operator manual January 2015 3-9008-001 Rev M Table 1-4 Daniel Senior Orifice Fitting sizes 10” thru 16” 150-900 Number required Parts and materials Size Item no.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M Notes:Table 1-4 1. All Daniel Senior Orifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory directly. 2. Locations of Equalizer Valve (1), Bleeder Valve (10B), and Grease Gun (23) may differ from diagrams shown in this manual. 3. Slide Valve Lubricant: 0.38in (9.53mm) diameter by 1.5in (38.
Section 1: Introduction January 2015 1.3.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M All Parts on Daniel Senior Orifice Fittings may be replaced or repaired without removing the Daniel Senior Orifice Fitting body from the line. Table 1-5 Daniel Senior Orifice Fitting sizes 10” thru 16” 1500 Number required Parts and materials Item no.
Section 1: Introduction Owner and operator manual January 2015 3-9008-001 Rev M Table 1-5 Daniel Senior Orifice Fitting sizes 10” thru 16” 1500 Number required Parts and materials Size Item no.
Owner and operator manual Section 1: Introduction January 2015 3-9008-001 Rev M Notes:Table 1-5 1. All Daniel Senior Orifice Fittings are supplied with pipe plugs on one side only. If additional quantities are required, please contact the factory directly. 2. Locations of Equalizer Valve (1), Bleeder Valve (10B), and Grease Gun (23) may differ from diagrams shown in this manual. 3. Slide Valve Lubricant: 0.38in (9.53mm) diameter by 1.5in (38.
Section 1: Introduction January 2015 28 Owner and operator manual 3-9008-001 Rev M Daniel Senior Orifice Fitting sizes 10”-16” 1500
Owner and operator manual 3-9008-001 Rev M Section 2: Installation January 2015 Section 2: Installation 21TOP (14) Figure 2-1 Daniel Senior Orifice Fitting component identification 2.1 General information The Daniel Senior Orifice Fitting is an essential element in an orifice plate flow measurement system. Other elements in the system usually include, but are not limited to, a meter tube, a flow conditioner, and various data recording devices.
Section 2: Installation January 2015 Owner and operator manual 3-9008-001 Rev M When assembling a flow measurement system that will contain a Daniel Senior Orifice Fitting, particular attention should be paid to the requirements for permanent joining of components. This will be to ensure optimal measurement performance and successful pressure test results. Referencing an appropriate measurement code (AGA-3, ISO 5167, etc.) will aid in this assembly.
Owner and operator manual Section 2: Installation January 2015 3-9008-001 Rev M 2.4 Severe service conditions If product owners or personnel expect that the Senior will encounter severe conditions (environment where there is likely to be an accumulation of sediment for any cause), then Daniel recommends the removal of the Drain Valve Plug (30) near the bottom of the Senior and the installation of a blow down valve in its place (refer to Section 3: Maintenance ). 2.
Section 2: Installation Owner and operator manual January 2015 2.5.2 3-9008-001 Rev M Internal corrosive environments For Daniel Senior Orifice Fittings located in internal corrosive environments, Daniel recommends that product owners purchase a Senior appropriate for the intended service. Daniel offers the Daniel Senior Orifice Fitting in a number of trims (Refer to Table 1-1 thru Table 1-5 for part and material lists).
Owner and operator manual Section 2: Installation January 2015 3-9008-001 Rev M Install the Senior in any horizontal line with the plate access opening in a vertical up position or with the Senior rotated left or right to give a horizontal opening position. Daniel Senior Orifice Fittings to 12" size may be installed in a vertical down flow direction. Figure 2-2 Daniel Senior Flangenek Fitting with meter tube 2.
Section 2: Installation Owner and operator manual January 2015 3-9008-001 Rev M • Confirm the Operating Wrench (2) operational clearances for the Plate Carrier (8DM or 8DMC) extraction, and meter tap equipment draw clearance. • Check shipment to verify that the shipping kit contains an Operating Wrench (2), Grease Gun (23), Indicator Plate (5A-marked “LH” for left-hand side operation) and Indicator Pointer (5B).
Owner and operator manual Section 2: Installation January 2015 3-9008-001 Rev M With the slide valve in the fully opened position, follow these instructions: - Rotate the Lower Plate Carrier Shaft (6) first. - Rotate the Upper Plate Carrier Shaft (7) to remove the Plate Carrier (8DM or 8DMC). - Put the Plate Carrier (8DM or 8DMC) in a safe, protected area for use later in the installation process.
Section 2: Installation Owner and operator manual January 2015 3-9008-001 Rev M FLUID EXPLOSION HAZARD Never pressurize a unit above the limits recommended in Section 1.2.1: Technical data of this manual. Before pressurizing the Daniel Senior Orifice Fitting, confirm the maximum allowable operating pressure (MAOP) of each item in the system. Over-pressurizing the Senior could lead to an explosive release of fluid resulting in serious injury or death. 1.
Owner and operator manual Section 2: Installation January 2015 3-9008-001 Rev M 6. If a leak is detected, mark the leak area with a marker and reduce the pressure inside the Senior to 0 psig (0 bar). Tighten any fastener or connector adjacent to the leak area and repeat the leak test again. 7. If after several attempts to contain the leakage, the leakage persists, call Daniel Customer Service for assistance.
Section 2: Installation Owner and operator manual January 2015 2.10 3-9008-001 Rev M Orifice Plate Installation After completion of the commissioning line pressure test in Section 2.9, install and lower the Plate Carrier (8DM or 8DMC) and Orifice Plate Assembly (13) into the Body (4) to begin measurement operations. EXPLOSION HAZARD Ensure that the Daniel Senior Orifice Fitting is at atmospheric pressure.
Owner and operator manual 3-9008-001 Rev M 5. Section 2: Installation January 2015 Orient the 2”-8” Plate Carrier (8DMC) assembly with the notch down. The notch end of the 2”-8” Plate Carrier (8DMC) assembly must enter the Senior first. Important Install the Plate Carrier (8DM or 8DMC) assembly into the Senior with the gear rack facing downstream and the notched end down (refer to Figure 2-3 and Figure 2-4).
Section 2: Installation January 2015 Owner and operator manual 3-9008-001 Rev M The diagram below depicts the proper orientation of the Plate Carrier (8DM or 8DMC) assembly prior to lowering it into the measurement position in the Senior. Figure 2-4 Orientation of Plate Carrier (8DM or 8DMC) Prior to Installation NOTES: 40 1. The gear rack side of the Plate Carrier (8DM or 8DMC) assembly must face the downstream direction of flow. 2.
Owner and operator manual Section 2: Installation January 2015 3-9008-001 Rev M 10. Install the Sealing Bar (9 or 9HP), the Sealing Bar Gasket (9A, 9A-HP or 9CF), and the Clamping Bar (12 or 12HP) in position on the Top (14) and tighten the Clamping Bar Screws (11). Refer to Section 5.3: Torque information for actual torque values to use. LOOSE CLAMPING BAR SCREW HAZARD The factory assembled and shipped this product with loose clamping bar screws.
Section 2: Installation January 2015 42 Owner and operator manual 3-9008-001 Rev M Orifice Plate Installation
Owner and operator manual 3-9008-001 Rev M Section 3: Maintenance January 2015 Section 3: Maintenance 3.1 Normal conditions Under normal measurement conditions, Daniel recommends lubricating the slide valve and exercising several key components of the Daniel Senior Orifice Fitting every thirty days (refer to Section 3.1.2: Component Exercise). If the plate changing operations are performed within this period, omit this operation. 3.1.1 Lubrication Important The information in this section, “3.1.
Section 3: Maintenance Owner and Operator Manual January 2015 3-9008-001 Rev M 1. Remove the stem from the Grease Gun (23) and insert a Daniel lubricant stick into the Grease Gun (23). Step 1 Step 1A PRESSURIZED FLUID HAZARD Using the Grease Gun (23), inject grease into the slide valve seat channels at a rate of 4 to 6 turns per minute and only under the following conditions: • • Bleeder Valve is open. Sealing bar/Clamping bar is in place and tight.
Owner and operator manual 3-9008-001 Rev M Section 3: Maintenance January 2015 Step 2 Important By turning the stem of the Grease Gun (23) at a rate of 4 to 6 turns per minute, the lubricant is forced through the Slide Valve Seat (18) channels at a rate that allows the lubricant to travel freely, yet not separate the valve strip from the valve seat. This method will keep fresh grease in the lubrication passages. 3. 3.1.2 Close Bleeder Valve (10B).
Section 3: Maintenance Owner and Operator Manual January 2015 3-9008-001 Rev M slide valve should travel freely in both directions with light resistance. Leave the slide valve in the OPEN position. Important The following operation will affect the flowing differential and will be shown on any chart or instrument, keep records of differential, unless these instruments are isolated. 4. Rotate the Lower Plate Carrier Shaft (6), located in the Body (4), one turn to raise the Plate Carrier (8DM or 8DMC).
Owner and operator manual Section 3: Maintenance January 2015 3-9008-001 Rev M 9. Remove the stem from the Grease Gun (23) with the Operating Wrench (2) and insert a Daniel lubricant stick into the Grease Gun (23). PRESSURIZED FLUID HAZARD Using the Grease Gun (23), inject grease into the slide valve seat channels at a rate of 4 to 6 turns per minute and only under the following conditions: • • Bleeder Valve is open. Sealing bar/Clamping bar is in place and tight.
Section 3: Maintenance January 2015 3-9008-001 Rev M 12. 48 Owner and Operator Manual If at any point during the exercise of the components, the resistance encountered when turning a shaft is greater than the torque applied by hand using the Wrench (2), further inspection of the Senior is required.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M Section 4: Orifice plate installation and removal instructions 4.1 Plate change procedure Follow these instructions during every plate change. FLUID EXPLOSION HAZARD Follow the instructions below to avoid inadvertent or accidental opening of the slide valve and the propulsion of fluid or internal components from the Top (4). Failure to do so will result in serious injury or death.
Section 4: Orifice plate installation and removal instructions January 2015 4.2 Owner and operator manual 3-9008-001 Rev M Selecting an appropriate plate change procedure EXPLOSION HAZARD The Daniel Senior Orifice Fitting contains fluid at elevated pressure. Make sure to follow the instructions below for proper installation and removal of the plate. Failure to do so can cause an explosive release and may result in serious injury or death.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M In order to assist the operator in determining the safest and most efficient means to perform the Orifice Plate (13) change on a Senior equipped with a grease assisted slide valve, Daniel prepared two plate change procedures that an operator may select from.
Section 4: Orifice plate installation and removal instructions January 2015 4.3 Owner and operator manual 3-9008-001 Rev M Orifice plate (13) change operation Important In order to perform a safe and efficient plate change operation with a Senior, the on-site personnel must evaluate both the service and environmental conditions prior to beginning this operation. These conditions may have a dramatic effect on the time required for an operator’s ability to return the Senior to its measurement condition.
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M 4.3.1 January 2015 “Quick change” procedure You may use the Quick change procedure for Daniel Senior Orifice Fittings equipped with an ORing (10E) soft seated valve and for Seniors equipped with a grease-assisted slide valve. Important Do not use this procedure if it cannot be finished in less than 15 minutes.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M Prior to performing any maintenance or Orifice Plate (13) installation and removal operations on the Senior, personnel must visually confirm the presence of the Indicator Plate (5A) on the Slide Valve Shaft (5) and the Indicator Pointer (5B) on the Body (4). Both the Indicator Plate and the Indicator Pointer must be installed to operate this equipment safely.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M FLUID EXPLOSION HAZARD Follow the instructions below to avoid inadvertent or accidental opening of the slide valve and the propulsion of fluid or internal components from the Top (4). Failure to do so will result in serious injury or death.
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M 2. Wait several seconds while the pressure in the Top (14) equalizes to that of the Body (4). 3. Using the Operating Wrench (2) rotate the Slide Valve Shaft (5) until it stops and the OPEN position specified on the Indicator Plate (5A) is in line with the Indicator Pointer (5B). Step 3 4.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M 6. Move the Operating Wrench (2) from the Lower Plate Carrier Shaft (6) located in the Body (4) on the Upper Plate Carrier Shaft (7) located in the Top (14). 7. Rotate the Upper Plate Carrier Shaft (7) located in the Top (14) until the Plate Carrier (8DM or 8DMC) stops against the Sealing Bar (9, 9HP). Step 7 Step 8 8. Close the Equalizer Valve (1) with the Operating Wrench (2).
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M 10. Open the Bleeder Valve (10B) with the Operating Wrench (2). PRESSURIZED FLUID HAZARD When opening the bleeder valve (10B) or venting the Top (14) thru the bleeder valve (10B), direct the released pressurized fluid and/or gas to safe area away from any individual in accordance with local environment regulations.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M Step 11 Step 11A PRESSURIZED FLUID HAZARD Using the Grease Gun (23), inject grease into the slide valve seat channels at a rate of 4 to 6 turns per minute and only under the following conditions: • • Bleeder Valve is open. Sealing bar/Clamping bar is in place and tight.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M Step 12 Important By turning the stem of the Grease Gun (23) at a rate of 4 to 6 turns per minute, the lubricant is forced through the Slide Valve Seat (18) channels at a rate that allows the lubricant to travel freely, yet not separate the valve strip from the valve seat. This method will keep fresh grease in the lubrication passages.
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M 13. January 2015 Monitor the fluid/gas pressure in the Top (14) until it is equal to ambient conditions. Important Once the Top (14) is equal to ambient conditions, the 15 minute countdown to remove and install the Orifice Plate Carrier (8DM or 8DMC) begins.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M Step 15 16. Slide the Clamping Bar (12 or 12HP) containing the Clamping Bar Screws (11), the Sealing Bar (9 or 9HP) from the Top (14). Step 16-17 62 17. Remove the Sealing Bar Gasket (9A, 9A-HP or 9CF) from the Top (14). 18.
Owner and operator manual 3-9008-001 Rev M Section 4: Orifice plate installation and removal instructions January 2015 continue to rotate the Upper Plate Carrier Shaft (7) until the Upper Plate Carrier Shaft (7) gears and the Plate Carrier (8DM or 8DMC) gear rack ratchet. Step 18 19. Remove the Orifice Plate Carrier (8DM or 8DMC) from the Top (14) and perform the scheduled work on the Orifice Plate (13) and Orifice Plate Carrier (8DM or 8DMC). 20.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M 22. Once the Orifice Plate Carrier (8DM or 8DMC) is aligned, rotate the Upper Plate Carrier Shaft (7) with the Operating Wrench (2), in a direction to lower the Orifice Plate Carrier (8DM or 8DMC) into the Top (14) until all of the Orifice Plate Carrier (8DM or 8DMC) is below the Sealing Bar Gasket (9A, 9A-HP or 9CF) surface.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M 24. Install the Sealing Bar (9 or 9HP) and the Clamping Bar (12 or 12HP) on to the Top (14). 25. Tighten each Clamping Bar Screw (11), located on the Clamping Bar (12 or 12HP), to the torque recommended in this manual (refer to Section 5.3: Torque information. Step 25 26. Step 26 Close the Bleeder Valve (10B).
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M 29. Using the Operating Wrench (2), rotate the Slide Valve Shaft (5) to the OPEN position. Step 29 Step 30 30. Rotate the Upper Plate Carrier Shaft (7) with the Operating Wrench (2) in the direction to lower the Orifice Plate Carrier (8DM or 8DMC) into the Body (4). 31.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M 32. Once the Orifice Plate Carrier (8DM or 8DMC) is positioned in the Body (4), turn the Slide Valve Shaft (5) using the Operating Wrench (2) into the CLOSED position. Step 32 33. Step 33 Close the Equalizer Valve (1).
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M 34. Open the Bleeder Valve (10B) to vent the Top (14). Step 34 Steps 35 and 36 are ONLY required for Seniors equipped with grease assisted, metal-to-metal slide valves. Personnel operating the Daniel Senior Orifice Fittings equipped with O-Ring seal “soft seat” design slide valves skip to step 37. 35.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M Step 35 Step 35A PRESSURIZED FLUID HAZARD Using the Grease Gun (23), inject the grease into the slide valve seat channels at a rate of 4 to 6 turns per minute and only under the following conditions: • • Bleeder Valve is open. Sealing bar/Clamping bar is in place and tight.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M Step 36 Important By turning the stem of the Grease Gun (23) at a rate of 4 to 6 turns per minute, the lubricant is forced through the Slide Valve Seat (18) channels at a rate that allows the lubricant to travel freely, yet not separate the valve strip from the valve seat. This method will keep fresh grease in the lubrication passages.
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M January 2015 Step 37 The Daniel Senior Orifice Fitting is now ready for measurement. 4.3.2 “Extended time” procedure This procedure is for the grease-assisted slide valves when the procedure takes over 15 minutes. However, it is acceptable for soft-seated valves.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M TOXIC EXPLOSION HAZARD Do not perform any of the following steps if the Indicator Plate, the Indicator Pointer, or both are not assembled on the Senior. Call Daniel Customer Service for assistance in obtaining replacement components, and follow the instructions provided in Section 2.8: Commissioning Daniel Senior Orifice Fitting installation.
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M January 2015 In preparation for the plate removal and installation process, the operator must evaluate the meter system to determine the amount of time between the Top (14) fluid evacuation and the plate change to the full replacement of the Clamping Bar (12 or 12HP), the Sealing Bar (9 or 9HP), and the Sealing Bar Gasket (9A, 9A-HP or 9CF) back on the Top (14).
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M Procedure: To remove the Orifice Plate (13) from the Daniel Senior Orifice Fitting, the operator must first balance the pressure between the Top (14) and the Body (4). 1. Step 1 Step 2 2. Wait several seconds while the pressure in the Top (14) equalizes to that of the Body (4). 3.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M 5. Step 5 Continue to rotate the Lower Plate Carrier Shaft (6) located on the Body (4) until the Upper Plate Carrier Shaft (7) located in the Top (14) begins to rotate. Step 6 6. Move the Operating Wrench (2) from the Lower Plate Carrier Shaft (6) located in the Body (4) on the Upper Plate Carrier Shaft (7) located in the Top (14). 7.
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M Step 9 10. Step 10 Open the Bleeder Valve (10B) with the Operating Wrench (2). PRESSURIZED FLUID HAZARD When opening the bleeder valve (10B) or venting the Top (14) thru the bleeder valve (10B), direct the released pressurized fluid and/or gas to safe area away from any individual in accordance with local environment regulations.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M Step 11 Step 11A PRESSURIZED FLUID HAZARD Using the Grease Gun (23), Inject the grease into the slide valve seat channels at a rate of 4 to 6 turns per minute and only under the following conditions: • • Bleeder Valve is open. Sealing Bar/Clamping bar is in place and tight.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M Step 12 Important By turning the stem of the Grease Gun (23) at a rate of 4 to 6 turns per minute, the lubricant is forced through the Slide Valve Seat (18) channels at a rate that allows the lubricant to travel freely, yet not separate the valve strip from the valve seat. This method will keep fresh grease in the lubrication passages.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M 13. Monitor the fluid/gas pressure in the Top (14) until it is equal to ambient conditions. RELEASE OF FLUIDS OR COMPONENTS HAZARD The Clamping Bar (12 or 12HP) may not be securely in place. Sudden release of fluid or internal components may occur. Never place the Operating Wrench (2) on the Slide Valve Shaft (5), or any body part in front of the top opening in the Top (14).
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M 15. Once the Clamping Bar Screws (11) are loose, rotate the Upper Plate Carrier Shaft (7) located in the Top (14) with the Operating Wrench (2), until the Plate Carrier (8DM or 8DMC) taps against the Sealing Bar (9 or 9HP) freeing it from the Top (14). 16. Slide the Clamping Bar (12 or 12HP) containing the Clamping Bar Screws (11), the Sealing Bar (9 or 9HP) from the Top (14).
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M January 2015 continue to rotate the Upper Plate Carrier Shaft (7) until the Upper Plate Carrier Shaft (7) gears and the Plate Carrier (8DM or 8DMC) gear rack ratchet. Step 18 19. Remove the Orifice Plate Carrier (8DM or 8DMC) from the Top (14) and perform the scheduled work on the Orifice Plate (13) and Orifice Plate Carrier (8DM or 8DMC). 20.
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M Step 20 Step 21 EXPLOSION HAZARD Follow the instructions in this manual to assure that the Sealing Bar Gasket (9A, 9A-HP or 9CF), the Sealing Bar (9 or 9HP) and the Clamping Bar (12 or 12HP) provide a pressure barrier between the line pressure and the atmosphere.
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M January 2015 Step 22 Important At this stage in the operational procedure, the Senior is at the following conditions: a) The Equalizer Valve (1) is closed. b) The Bleeder Valve (10B) closed. c) The Slide Valve is closed. d) The Sealing Bar (9 or 9HP), the Clamping Bar (12 or 12HP), and a new Sealing Bar Gasket (9A, 9A-HP or 9CF are installed on the Top (14).
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M 24. Open the Bleeder Valve (10B) with the Operating Wrench (2) Step 24 Steps 25 and 26 are ONLY required for the Seniors equipped with grease assisted, metal-tometal slide valves. Personnel operating Seniors equipped with O-Ring seal “soft seat” design slide valves skip to step 27. 25.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M 26. Return the stem to the Grease Gun (23) and begin turning it clockwise by hand into the Grease Gun (23) until resistance is felt. Once this is done, use the supplied Operating Wrench (2) to continue to turn the stem at a rate of 4 to 6 turns per minute.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M Important By turning the stem of the Grease Gun (23) at a rate of 4 to 6 turns per minute, the lubricant is forced through the Slide Valve Seat (18) channels at a rate that allows the lubricant to travel freely, yet not separate the valve strip from the valve seat. This method will keep fresh grease in the lubrication passages.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M Step 28 Step 29 29. Once the Clamping Bar Screws (11) are loose, it may be necessary to use the Operating Wrench (2) to tap against the Sealing Bar (9 or 9HP) freeing it from the Top (14). 30. Slide the Clamping Bar (12 or 12HP) containing the Clamping Bar Screws (11), the Sealing Bar (9) from the Top (14). Step 30-31 31.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M 32. Insert the Orifice Plate Carrier (8DM or 8DMC) into the Top (14) until the Upper Plate Carrier Shaft (7) gears and plate carrier gear rack mesh. 33. With the Operating Wrench (2), rotate the Upper Plate Carrier Shaft (7), located in the Top (14), a minimum of one quarter turns OPPOSITE of the direction required to lower the Orifice Plate Carrier (8DM or 8DMC) into the Top (14).
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M January 2015 EXPLOSION HAZARD Follow the instructions in this manual to assure that the Sealing Bar Gasket (9A, 9A-HP or 9CF), the Sealing Bar (9 or 9HP) and the Clamping Bar (12 or 12HP) provide a pressure barrier between the line pressure and the atmosphere. Failure to properly install these parts may result in explosive separation of components resulting in serious injury or death. 35.
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M Step 37 38. Close the Bleeder Valve (10B). 39. Open the Equalizer Valve (1) one-half to two turns with the Operating Wrench (2). Step 39 90 Step 38 Step 40 40. Wait several seconds for the Top (14) to reach pressure equilibrium with the line pressure contained in the Body (4). 41. Using the Operating Wrench (2), rotate the Slide Valve Shaft (5) to the OPEN position.
Owner and operator manual Section 4: Orifice plate installation and removal instructions January 2015 3-9008-001 Rev M Step 41 Step 42 42. Rotate the Upper Plate Carrier Shaft (7) located in the Top (14) with the Operating Wrench (2) in the direction to lower the Orifice Plate Carrier (8DM or 8DMC) into the Body (4). 43. Rotate the Lower Plate Carrier Shaft (6) with the Operating Wrench (2) until the Orifice Plate Carrier (8DM or 8DMC) cannot be lowered further.
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M Important Resistance to turning will be present when the Orifice Plate Carrier (8DM or 8DMC) is approaching its proper measurement position due to friction between the Senior Body (4) and the Orifice Plate (13) seal. 44. Once the Orifice Plate Carrier (8DM or 8DMC) is positioned in the Body (4), turn the Slide Valve Shaft (5) using the Operating Wrench (2) into the CLOSED position.
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M 46. January 2015 Open the Bleeder Valve (10B) to vent the Top (14). Step 46 Step 47 and 48 are ONLY required for Seniors equipped with grease assisted, metal-to-metal slide valves. Personnel operating the Daniel Senior Orifice Fitting equipped with O-Ring seal “soft seat” design slide valves skip to step 49. 47.
Section 4: Orifice plate installation and removal instructions Owner and operator manual January 2015 3-9008-001 Rev M Step 47 Step 47A PRESSURIZED FLUID HAZARD Using the Grease Gun (23), inject the grease into the slide valve seat channels at a rate of 4 to 6 turns per minute and only under the following conditions: • • Bleeder Valve is open. Sealing Bar/Clamping bar is in place and tight.
Owner and operator manual Section 4: Orifice plate installation and removal instructions 3-9008-001 Rev M 48. January 2015 Return the stem to the Grease Gun (23) and begin turning it clockwise by hand into the Grease Gun (23) until resistance is felt. Once this is done, use the supplied Operating Wrench (2) to continue to turn the stem at a rate of 4 to 6 turns per minute.
Section 4: Orifice plate installation and removal instructions January 2015 Owner and operator manual 3-9008-001 Rev M 49. Close the Bleeder Valve (10B). Step 49 The Daniel Senior Orifice Fitting is now ready for measurement.
Owner and operator manual Section 5: Supplemental information January 2015 3-9008-001 Rev M Section 5: Supplemental information 5.1 Recommended spare parts for one-year operation Table 5-1 Recommended spare parts Item No.
Section 5: Supplemental information January 2015 5.2 Owner and operator manual 3-9008-001 Rev M Lubricant information Product owners and operating personnel select the Daniel Senior Orifice Fitting for use in a wide variety of flow measurement services around the world. Information and experience gathered indicate that measurement service conditions do have a profound effect on the metal-to-metal slide valve sealing performance.
Owner and operator manual 3-9008-001 Rev M Section 5: Supplemental information January 2015 Figure 5-1 Standard grease - Type 1 Pressure (psig) v. Temperature (°F) STANDARD GREASE - TYPE 1 - Part Number:1-213-04-001 OPTIMUM SEALING RANGE WITH NITROGEN FOR A 3" ANSI 600 SENIOR FITTING UNDER LABORATORY CONDITIONS. Colored coordinate boxes indicate no detectable leakage at that Temperature and Pressure for 30 minutes. This information can be used as a guideline when evaluating measurement applications.
Section 5: Supplemental information January 2015 Owner and operator manual 3-9008-001 Rev M Figure 5-2 Sour grease - Type 2 Pressure (psig) v. Temperature (°F) SOUR GAS GREASE - TYPE 2 - Part Number:1-213-04-102 OPTIMUM SEALING RANGE WITH NITROGEN FOR A 3" ANSI 600 SENIOR FITTING UNDER LABORATORY CONDITIONS. Colored coordinate boxes indicate no detectable leakage at that Temperature and Pressure for 30 minutes. This information can be used as a guideline when evaluating measurement applications.
Owner and operator manual 3-9008-001 Rev M Section 5: Supplemental information January 2015 Figure 5-3 Carbon dioxide grease - Type 3 Pressure (psig) v. Temperature (°F) CARBON DIOXIDE GREASE - TYPE 3 - Part Number:1-213-04101 OPTIMUM SEALING RANGE WITH NITROGEN FOR A 3" ANSI 600 SENIOR FITTING UNDER LABORATORY CONDITIONS. Colored coordinate boxes indicate no detectable leakage at that Temperature and Pressure for 30 minutes.
Section 5: Supplemental information January 2015 Owner and operator manual 3-9008-001 Rev M Figure 5-4 High temperature grease - Type 4 Pressure (psig) v. Temperature (°F) HIGH TEMPERATURE GREASE - TYPE 4 - Part Number:1-21304-103 OPTIMUM SEALING RANGE WITH NITROGEN FOR A 3" ANSI 600 SENIOR FITTING UNDER LABORATORY CONDITIONS. Colored coordinate boxes indicate no detectable leakage at that Temperature and Pressure for 30 minutes.
Owner and operator manual Section 5: Supplemental information January 2015 3-9008-001 Rev M 5.3 Torque information Daniel utilizes several joint assemblies constructing the Senior. To successfully pass all factory tests, factory personnel torque each fastener in the joint assembly to contain pressure and seal the unit. Product owners and product operators must realize that service conditions and time will impact the tightness and strength of factory assembled joints.
Section 5: Supplemental information Owner and operator manual January 2015 3-9008-001 Rev M Table 5-3 Clamping bar screw (11) quantity and torque requirements Screw size Minimum Maximum 150 4 1/2”-13 75 95 300 4 1/2”-13 75 95 600 4 1/2”-13 75 95 900 4 1/2”-13 110 110 1500 8 5/8”-11 145 180 2500 10 5/8”-11 145 180 150 4 1/2”-13 95 120 300 4 1/2”-13 95 120 600 4 1/2”-13 95 120 900 4 5/8”-11 120 150 1500 10 5/8”-11 145 180 2500 10 5/8”-11 145 1
Owner and operator manual Section 5: Supplemental information January 2015 3-9008-001 Rev M Table 5-3 Clamping bar screw (11) quantity and torque requirements Screw size Minimum Maximum 150 8 1/2”-13 75 95 300 8 1/2”-13 75 95 600 8 1/2”-13 75 95 900 8 5/8”-11 145 180 1500 20 5/8”-11 145 180 2500 28 5/8”-11 145 180 150 10 1/2”-13 75 95 300 10 1/2”-13 95 120 600 10 1/2”-13 95 120 900 10 5/8”-11 120 150 1500 20 5/8”-11 145 180 2500 28 5/8”-11 14
Section 5: Supplemental information January 2015 Owner and operator manual 3-9008-001 Rev M Figure 5-5 Torque pattern sequences 106 Joint assembly procedures
Owner and operator manual Section 5: Supplemental information January 2015 3-9008-001 Rev M Table 5-4 Seat Screw Torque LBF-FT Torque (lbf-ft) Size Min Max STD Trim 2”-8” 45 55 STD Trim 10” 50 65 STD Trim 12” +: 55 70 316, Monel & all AASG 35 45 Important Daniel calculated the torque values below based on the following design parameters: • Zinc plated 4130 Carbon Steel screws • Rubber bonded compressed fiber material gasket • Assembly at room temperature, factory conditions • Servi
Section 5: Supplemental information Owner and operator manual January 2015 3-9008-001 Rev M Table 5-5 Daniel Senior Orifice Fitting Body(4) / Top (14) stud torque FT-LBS Torque Size (in.) 4 6 8 10 12 108 ANSI class No.
Owner and operator manual Section 5: Supplemental information January 2015 3-9008-001 Rev M Table 5-5 Daniel Senior Orifice Fitting Body(4) / Top (14) stud torque FT-LBS Torque Size (in.) 14 16 ANSI class No.
Section 5: Supplemental information Owner and operator manual January 2015 5.4 3-9008-001 Rev M Plate and valve carrier clearances Table 5-6 Plate carrier to valve carrier clearances (inches) 5.5 5.5.1 Line size Minimum clearance Maximum clearance 2 .006 .018 3 .006 .018 4 .006 .018 6 .006 .018 8 .006 .018 10 .008 .023 12 .009 .028 14 .010 .030 16 .012 .
Owner and operator manual Section 5: Supplemental information January 2015 3-9008-001 Rev M 5.5.2 Material List The field technician will need to verify that all materials necessary for the retro-fit are included in the parts kit prior to beginning this procedure. Below is a breakdown of those parts and quantities (refer to Figure 5-6 for pictorial reference). Should any parts be missing, contact your authorized Daniel representative for replacement parts. Table 5-7 Material list Item no.
Section 5: Supplemental information January 2015 5.5.3 Owner and operator manual 3-9008-001 Rev M Disassembly Important It is not necessary to remove the Senior from the process line to facilitate these instructions. Removing the Daniel Senior Orifice Fitting should only be done at the discretion of the end user and after completing Step 1, below. Refer to Figure 5-6 for pictorial reference. 1. Isolate the Senior from line pressure. 2.
Owner and operator manual Section 5: Supplemental information 3-9008-001 Rev M January 2015 11. Store these items in a safe place for reuse later (remove the plate/seal assembly from the Plate Carrier (8DM or 8DMC) and store as a separate item). 12. Mark four places minimum on the Body (4) and Top (14) crown flanges for match marks, one each per side (six marks preferred, two each per long side and one each per short side). 13.
Section 5: Supplemental information January 2015 5.5.4 Owner and operator manual 3-9008-001 Rev M Slide valve removal 2" - 14" Only - From inside the slide valve cavity of the Body (4), remove the Slide Valve Strip (3), Slide Valve Carrier (17), Slide Valve Springs (15) and Slide Valve Carrier Guides (16). These items will not be reused. Their replacements are in the parts kit.
Owner and operator manual Section 5: Supplemental information 3-9008-001 Rev M 5.5.6 January 2015 Senior Fittings 2"-8" for "API-14.3" 1. Retrieve the Plate Carrier (8DM or 8DMC) from its safe storage. 2.
Section 5: Supplemental information January 2015 5.5.7 Owner and operator manual 3-9008-001 Rev M Senior Fittings 2"-8" Non "API-14.3" & all 10" thru 12" 1. Retrieve the Plate Carrier (8DM or 8DMC) from its safe storage. 2.
Owner and operator manual Section 5: Supplemental information 3-9008-001 Rev M January 2015 Re-assemble the Top (14) as instructed below. 1. Retrieve the Top (14) from its safe storage. Verify that the gaskets surfaces (sealing bar region of tee-slot and the crown flange) have been cleaned of all residue. 2. Place the Top (14) on a clean, sturdy surface with the crown flange facing upward. 3.
Section 5: Supplemental information January 2015 Owner and operator manual 3-9008-001 Rev M LIFTING HAZARD The field technician should always use mechanical assistance when lifting the Top (14). Failure to do so may result in serious injury. 18. Using a jib crane or equivalent, gently lower the Top (14) onto the Body (4). Make certain that the match up lines on the crown flanges of the Top (14) and Body (4) line up as close as possible. 19.
Owner and operator manual Section 5: Supplemental information 3-9008-001 Rev M January 2015 29. Rotate the Slide Valve Shaft (5) to move the soft seat slide valve assembly into its full “open” position. 30. Install the balance of the stud bolt Hex Nuts (32) and tighten to “snug” only. 31. Apply torque to the Hex Nuts (32) in a crisscross fashion, working from the center of the crown flange outward. 32. Tighten the Hex Nuts (32) to the minimum torque values shown in Table 5-4.
Section 5: Supplemental information January 2015 Owner and operator manual 3-9008-001 Rev M 47. Apply line pressure to the Senior and verify that the gasket joints of the Sealing Bar (9 or 9HP)/Top (14) and the crown flanges of the Body are not leaking. 48. Close the Equalizer Valve (1) and rotate the Slide Valve Shaft (5) to close the Soft Seat Slide Valve assembly.
Owner and operator manual 3-9008-001 Rev M Section 5: Supplemental information January 2015 Figure 5-6 Daniel Senior Orifice Fitting Refer to Table 5-7 in Section 5: Supplemental information for item numbers and part descriptions Important Fittings manufactured after July 1985 use these stuffing box and bearing plug parts. The parts are interchangeable to prior dated fittings, but may require minor field modification (shortening) of the sleeves only. Senior Fittings 2"-8" Non "API-14.
Section 5: Supplemental information January 2015 Owner and operator manual 3-9008-001 Rev M Figure 5-7 Stuffing box and bearing plug 122 Senior Fittings 2"-8" Non "API-14.
P/N 3-9008-001 Rev M 2015 Daniel Measurement and Control, Inc. 11100 Brittmoore Park Drive Houston, TX 77041 USA T+1 713-467-6000 F+1 713-827-4805 USA Toll Free 1 888-356-9001 Daniel Measurement Services, Inc. T +1 713-827-6314 www.Daniel.com Europe: Stirling, Scotland, UK T + 44-1786-433400 Middle East: Africa: Dubai, UAE T +971-4-811-8100 Asia Pacific: Singapore T +65-677-8211 © 2015 Daniel Measurement and Control, Inc.
