012D WELLS MANUFACTURING 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by Wells Manufacturing is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only. by unauthorized personnel.
TABLE OF CONTENTS WARRANTY FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION MAINTENANCE INSTRUCTIONS CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS WIRING DIAGRAM EXPLODED VIEW & PARTS LIST PARTS & SERVICE CUSTOMER SERVICE DATA xi 2 3 3 4 6 7 8 10 10 11 12 13 INTRODUCTION Thank You for purchasing this Wells Manufacturing appliance.
FEATURES & OPERATING CONTROLS INDICATOR LIGHT TEMPERATURE CONTROL (INFINITE SWITCH) IL2614 IMPORTANT: DO NOT LEAVE ON “PREHEAT” Unit may cycle on hi-limit control, leading to premature failure of the hi-limit control device. A. INFINITE SWITCH 1. On INFINITE SWITCH controlled warmers, power is applied to the heating element based on the control knob position, which varies the duty cycle of the heating element. 2. The desired temperature is controlled by rotating the temperature control knob.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments only. This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
INSTALLATION NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation. UNPACKING & INSPECTION Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. Carefully read all instructions in this manual and the Installation Instruction Sheet packed with the appliance before starting any installation.
INSTALLATION 4. For “top-mounted” warmers (i.e. warmers mounted from above the counter top): a. Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout. b. After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter c. Apply a thin bead of food-grade silicone sealant around the flange to seal it to the counter. d.
OPERATION Hot Surface Exposed surfaces can be hot to the touch and may cause burns. CAUTION: Shock Hazard DO NOT splash or pour water onto control panel or wiring. Always use an inset. DO NOT place food directly into the warmer. Always pour hot water into the warmer before it is preheated. pour water into a dry, heated warmer. This may damage the unit. DO NOT put ice into a warmer pan. This will cause condensation on the inside of the warmer. Damage caused by condensation is NOT covered by warranty.
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
CLEANING INSTRUCTIONS Shock Hazard DAILY CLEANING INSTRUCTIONS PREPARATIONS: Turn control knob(s) to OFF. Allow warmer to cool before proceeding. Remove any insets, pans and/or adapter tops ( if used). Drain or remove water from well if used for wet operation. FREQUENCY: Minimum - daily. TOOLS: Mild Detergent Solution: 10 Parts Warm Water to 4 Parts Vinegar Plastic Scouring Pad Clean Cloth or Sponge Food-Grade Silicone Sealant Do NOT splash or pour water into or over any control panel or wiring.
CLEANING INSTRUCTIONS CAUTION: WEEKLY CLEANING INSTRUCTIONS PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge 1. Add water to pans until water is at normal operating level (1” - 1 1/2” deep) or covers accumulated scale. 2.
TROUBLESHOOTING SUGGESTIONS SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY No power to warmer Circuit breaker off or tripped Reset circuit breaker Warmer will not heat Temperature control not set Set control to desired temperature Wet insulation Verify flange-to counter seal is sound, or reseal with food-grade silicone sealant Pan leaking or other internal damage Contact your Authorized Wells Service Agency for repairs Internal damage Contact your Authorized Wells Service Agency for repairs Mineral
EXPLODED VIEW & PARTS LIST 1 2 16 3 2M-308034; Drop-In Round Warmer w/Infinite Switch Control 4 11 12 10 13 8 6 14 9 15 7 5 Model: SS-4, SS-8 & SS-10 SS-4D, SS-8D & SS-10D (with Drain) 11 IL1997 Rev.
EXPLODED VIEW & PARTS LIST December 9, 2013 Model: SS4, SS8, SS10 Round Warmers 1 2 3 Part No Description P2-31869 SCREEN DRAIN ASSY, WARMERS DRAIN UNITS WS-63527 POT FOR SS4 SS4 WS-63528 POT FOR SS4D SS4D WS-50391 POT FOR SS8 SS8 WS-50504 POT FOR SS8D SS8D WS-51232 POT FOR SS10 SS10 WS-50392 POT FOR SS10D SS10D WS-506274 WS-506275 KIT, ELEMENT & SUPPORT 4 WS-51878 ELEMENT COVER 5 2R-44373 KNOB CONTROL ASSY 6 WS-50385 LIGHT SIGNAL RED, w/CLIP 7 2V-WL0049 PANEL, CONTRO
PARTS & SERVICE DESCRIPTION PART NO. ADAPTERS & INSETS Adapter top, convert SS8 to hold 4 qt. inset WS-20177 Adapter top, convert SS10 to hold 4 qt. inset WS-20822 Adapter top, convert SS10 to hold 7 qt. inset WS-20175 Adapter top, convert SS206 to hold two 7 qt. insets WS-20176 4 QT. ROUND INSET w/ lid WS-20774 7 QT. ROUND INSET w/ lid WS-20587 11 QT. ROUND INSET w/ lid WS-20908 11 QT.
WELLS MANUFACTURING 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
