011B WELLS MANUFACTURING 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by Wells Manufacturing is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only. prices charged by Wells Manufacturing for its products are based upon the limitations in this warranty.
TABLE OF CONTENTS WARRANTY FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION MAINTENANCE INSTRUCTIONS CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS WIRING DIAGRAM EXPLODED VIEW & PARTS LIST PARTS & SERVICE CUSTOMER SERVICE DATA xi 2 3 3 4 6 7 8 10 11 14—17 20 21 INTRODUCTION M011B.03 2M-308016 Owners Manual for Unshrouded Drop-In Bottom Mounted Warmers w/T-Stat Controls Thank You for purchasing this Wells Manufacturing appliance.
FEATURES & OPERATING CONTROLS A. THERMOSTAT 1. On THERMOSTATICALLY CONTROLLED warmers, power is applied to the heating element according to the control knob position and the actual temperature at the temperature sensing thermobulb. 2. The desired temperature is controlled by rotating the TEMPERATURE CONTROL KNOB. The knob has a numeric scale, where higher numbers correspond to higher temperature. 3.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments only. This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
INSTALLATION NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. WARNING: Risk of injury Carefully remove the appliance from the carton. Remove all protective plastic film, packing materials and accessories from the Appliance before connecting electrical power or otherwise performing any installation procedure.
INSTALLATION 4. For “top-mounted” warmers (i.e. warmers mounted from above the counter top): a. Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout. b. After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter c. Apply a thin bead of food-grade silicone sealant around the flange to seal it to the counter. d.
OPERATION CAUTION: Hot Surface Exposed surfaces can be hot to the touch and may cause burns. WET OR DRY OPERATION for WARMERS 1. Carefully read the description of the warmer operation on the specification sheet. 2. CAUTION: Shock Hazard DO NOT splash or pour water onto control panel or wiring. 3. Always use an inset. Always pour hot water into the warmer before it is preheated. DO NOT pour water into a dry, heated warmer. This may damage the unit. DO NOT put ice into a warmer pan.
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
CLEANING INSTRUCTIONS CAUTION: Shock Hazard DAILY CLEANING INSTRUCTIONS PREPARATIONS: Turn control knob(s) to OFF. Allow warmer to cool before proceeding. Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Minimum - daily. TOOLS: Mild Detergent Solution: 10 Parts Warm Water to 4 Parts Vinegar Plastic Scouring Pad Clean Cloth or Sponge Food-Grade Silicone Sealant Do NOT splash or pour water into or over any control panel or wiring.
CLEANING INSTRUCTIONS WEEKLY CLEANING INSTRUCTIONS CAUTION: PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge 1. Add water to pans until water is at normal operating level M011B.
TROUBLESHOOTING SUGGESTIONS SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY No power to warmer Circuit breaker off or tripped Reset circuit breaker Warmer will not heat Temperature control not set Set control to desired temperature Wet insulation Verify flange-to counter seal is sound, or reseal with food-grade silicone sealant Pan leaking or other internal damage Contact your Authorized Wells Service Agency for repairs Internal damage Contact your Authorized Wells Service Agency for repairs Warmer
M011B.
WIRING DIAGRAM M011B.
M011B.
EXPLODED VIEW & PARTS LIST MODELS SS206T(D) & SS206ET(D) 2 Top Mount 1 3 Bottom Mount 11 4 10 9 5 8 6 7 IL1972b, PL011B, 4/25/12 14 M011B.
EXPLODED VIEW & PARTS LIST Model: SS206T(D) & SS206ET(D) Fig No 1 Part No. P2-31869 Qty 1 P2-30401 2 3 M011B.
EXPLODED VIEW & PARTS LIST MODELS SS206ULT(D) & SS276ULT(D) DRAIN SCREEN ASSEMBLY P2-31869 WARMER PAN WS-50401, (SS206ULT) WS-60858, (SS206ULTD) WS-63739, (SS276ULT) WS-63740, (SS276ULTD) ELEMENT, HEATING 2N-46681UL (120V) 2N-303375UL (208/240V) ELEMENT CLAMP 2C-30467 ELEMENT & PAN KIT WS-67627 (120V) WS-67645 (208/240V) BRACKET, THERMOLB P2-45812 PAN, ELEMENT WS-507715 THERMOSTAT, CONTROL SS206ULT(D), 2T-45917 SS276ULT(D), 2T-38968 96” CAP, 2T-46551 CONDUIT, FLEX 1/2” x 28” P2-40634 THERMOSTAT MOUN
EXPLODED VIEW & PARTS LIST MODEL SS276T(D) WARMER PAN SS-276T (2-studs) - P2-WL0058 SS-276T (6-studs) - WS-63739 SS-276TD - WS-63740 (1/2” DRAIN) SS-276TD - WS-68760 (1” DRAIN) M011B.
NOTES M011B.
M011B.
PARTS & SERVICE Always use an inset. DESCRIPTION DO NOT place food directly into the warmer pan. ADAPTERS & INSETS PART NO. Adapter top, convert SS206 to hold two 7 qt. insets WS-20176 Adapter top, convert SS206 to hold two 4 qt. insets and two 2½ qt. insets WS-20434 Adapter top, convert SMPT, HW/SMP or 1 side of TMPT to hold three 4 qt. insets WS-21615 Adapter top, convert SMPT, HW/SMP or 1 side of TMPT to hold one 7 qt. and one 4 qt.
PARTS & SERVICE DESCRIPTION PART NO.
WELLS MANUFACTURING 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
