011D WELLS MANUFACTURING 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
LIMITED WARRANTY STATEMENT limitations in this warranty. Seller’s obligation under this warranty is limited to the repair of defects without charge by a Wells factory authorized service agency or one of its sub-service agencies. This service will be provided on customer’s premises for non-portable models. Portable models (a device with a cord and plug) must be taken or shipped to the closest authorized service agency, transportation charges prepaid, for service.
TABLE OF CONTENTS WARRANTY FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION MAINTENANCE INSTRUCTIONS CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS WIRING DIAGRAM EXPLODED VIEW & PARTS LIST Non Auto-Fill Units Auto-Fill Units ACCESSORIES LIST CUSTOMER SERVICE DATA xi 2 3 3 4 7-8 9 10-11 12 12-13 14 18 20 21 INTRODUCTION M011D.01 2M-Z17558 Owners Manual for Built-In Round T’Stat Warmers Thank You for purchasing this Wells appliance.
FEATURES & OPERATING CONTROLS A. THERMOSTAT INDICATOR LIGHT TEMPERATURE CONTROL KNOB 1. On THERMOSTATICALLY CONTROLLED warmers, power is applied to the heating element according to the control knob position and the actual temperature at the temperature sensing thermobulb. 2. The desired temperature is controlled by rotating the TEMPERATURE CONTROL KNOB. The knob has a numeric scale, where higher numbers correspond to higher temperature. 3.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments only. This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
INSTALLATION WARNING: RISK OF INJURY Installation procedures must be performed by a qualified technician with full knowledge of all applicable electrical and plumbing codes. Failure can result in personal injury and property damage. UNPACKING & INSPECTION Carefully remove the appliance from the carton. Remove all protective plastic film, packing materials and accessories from the Appliance before connecting electrical power or otherwise performing any installation procedure.
INSTALLATION continued 4. For “top-mounted” warmers (i.e. warmers mounted from above the counter top): a. Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout. b. After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter c. Apply a thin bead of food-grade silicone sealant around the flange to seal it to the counter. d.
INSTALLATION continued WARNING: RISK OF INJURY While local plumbing codes may allow the use of pcv, cpvc, abs or other plastic pipe for drain connections. DO NOT attach a plastic drain to the bottom of the food warmer. These units will contain water with temperatures in excess of 180°F and localized metal temperatures in excess of 275°F (135°C). Failure to follow these directions may result in personal injury and property damage.
OPERATION CAUTION: WET OR DRY OPERATION for WARMERS 1. Carefully read the description of the warmer operation on the specification sheet. 2. a. Most warmers are designed for WET OR DRY operation, except AUTOFILL units.. b. Warmers may be used wet, or may be used dry. However warmers may NOT be used wet-to-dry or dry-to-wet unless they have been allowed to cool to room temperature between the change in wet or dry operation. 3. c.
OPERATION continued CAUTION: HOT SURFACE Exposed surfaces can be hot to the touch and may cause burns. CAUTION: SHOCK HAZARD AUTOFILL WARMERS 1. Autofill warmers sense water level by a sensor placed at the proper level. For manifolded autofill warmers, the water level sensor / fill tube is in one pan only. 2. Water fills the pan through an inlet tube. All other sections if manifolded, fill at the same time through the drain manifold. 3.
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
CLEANING INSTRUCTIONS SHOCK HAZARD Do NOT splash or pour water into or over any control panel or wiring. CAUTION: SHOCK HAZARD DAILY CLEANING INSTRUCTIONS PREPARATIONS: Turn control knob(s) to OFF. Allow warmer to cool before proceeding. Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Minimum - daily.
CLEANING INSTRUCTIONS CAUTION: WEEKLY CLEANING INSTRUCTIONS PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge 1. Add water to pans until water is at normal operating level (1” - 1 1/2” deep) or covers accumulated scale. 2.
TROUBLESHOOTING SUGGESTIONS POSSIBLE CAUSE SUGGESTED REMEDY No power to warmer Circuit breaker off or tripped Reset circuit breaker Warmer will not heat Temperature control not set Set control to desired temperature Wet insulation Verify flange-to counter seal is sound, or reseal with foodgrade silicone sealant Pan leaking or other internal damage Contact your Authorized Wells Service Agency for repairs Internal damage Contact your Authorized Wells Service Agency for repairs Mineral deposits o
WIRING DIAGRAM FOR SS4ULT(C); SS8ULT(C); SS10ULT(C) 120 OR 208/240V SINGLE PHASE WITH OR WITHOUT OPTIONAL POWER CORD HEATER ELEMENT 16 GA. NICKEL STRANDED APPLIANCE WIRE. GREEN BLACK 5 GREEN M011D.01 2M-Z17558 Owners Manual for Built-In Round T’Stat Warmers WIRING DIAGRAM 825 620 825 450 338 450 240 208 120 240 208 120 WATTS VOLTS 2 1 THERMOSTAT 3.4 3.0 6.9 1.9 1.6 3.8 NOM.
EXPLODED VIEW & PARTS LIST SS8T and SS10T with & without Drain 1 2 3 4 10 9 5 M011D.01 2M-Z17558 Owners Manual for Built-In Round T’Stat Warmers 7 6 11 12 13 14 15 8 16 17 21 20 18 19 Model: SS4T, SS8T & SS10T (w & w/o Drain) SS4TU, SS8TU & SS10TU (w & w/o Drain) IL1904 Rev.
PARTS LIST SS4T, SS8T & SS10T units with & without drain December 11, 2013 Model: SS4T, SS8T, SS10T (Insulated & non-insulated) with & without Drian Fig No 1 Part No. 2V-Z17446 Description Drain Screen Qty 1 WS-63527 WS-50391 SS4ULT Pot Assembly SS8ULT, SS8T SS10ULT, SS10T WS-63528 SS4ULTD Pot Assembly w/Drain WS-50392 SS8ULTD, SS8TD 1 P2-WL0292 P2-WL0290 Pot Assembly Insulated SS10TUI P2-WL0291 SS4TDUI P2-WL0321 M011D.
PARTS LIST SS4T, SS8T & SS10T units with & without drain December 11, 2013 Model: SS4T, SS8T, SS10T (Insulated & non-insulated) with & without Drian Part No.
M011D.
EXPLODED VIEW AUTO-FILL 1 2 3 4 29 5 30 18 7 32 31 28 27 8 33 34 9 24 10 23 22 25 26 19 11 9 12 21 20 13 14 15 16 17 18 SK2697, Rev. - , 10/17/13 Model: SS10TDUIAF (w Drain & AUTO-FILL) 18 M011D.
PARTS LIST AUTO-FILL SS8TDUIAF & SS10TDIAF units with drain & Autofill Fig No.
ACCESSORIES LIST Always use an inset. DESCRIPTION PART NO. DO NOT place food directly into the warmer pan. ADAPTERS & INSETS WS-20177 ADAPTER TOP, convert SS10 to hold 4 qt. inset WS-20822 ADAPTER TOP, convert SS10 to hold 7 qt. inset WS-20175 2½ QT. ROUND INSET w/ lid NLA 4 QT. ROUND INSET w/ lid WS-20774 7 QT. ROUND INSET w/ lid WS-20587 11 QT. ROUND INSET w/ lid WS-20908 11 QT. ROUND INSET w/ hinged lid WS-21057 M011D.
PARTS & SERVICE DESCRIPTION PART NO. ACCESSORIES 8 oz. SOUP LADLE 2L-47567 WELLSLOK EXTENSION KIT, for UL LISTED circular warmers only, adapt to wood counter up to 1¾” thick IMPORTANT: Use only factory authorized service parts and replacement filters.
WELLS MANUFACTURING 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
