273 OPERATION MANUAL CONVECTION OVEN MODELS OC-4HC WITH CERAMIC COOKTOP & OC-4TC WITH HOTPLATE COOKTOP Includes INSTALLATION USE & CARE OC-4HC IMPORTANT: DO NOT DISCARD THIS MANUAL This manual is considered to be part of the appliance and is to be given to the OWNER or MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of this appliance. Additional manuals are available from your WELLS DEALER.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by WELLS MFG. CO. is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only.
TABLE OF CONTENTS WARRANTY SPECIFICATIONS FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION INSTALLATION AGENCY APPROVAL INFORMATION OPERATION COOKING SUGGESTIONS CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS PREVENTATIVE MAINTENANCE PARTS & SERVICE CUSTOMER SERVICE DATA xi 1 2 4 5 5 8 10 11 13 14 15 15 INTRODUCTION Thank You for purchasing this Wells Manufacturing Co. appliance.
FEATURES & OPERATING CONTROLS Fig.
FEATURES & OPERATING CONTROLS (continued) FEATURES & OPERATING CONTROLS CAUTION: COOKTOP CONTROLS 1. Four sections are controlled by individual infinite switch controls. 2. Associated power indicator will glow any time section is ON. HOT SURFACE OVEN POWER SWITCH (ON-OFF-FAN): 1. ON position (with door closed). POWER ON indicator will glow, blower fan will come on and unit will start to heat. NOTE: In the ON position, if the door is opened, blower fan is turned off and heating elements are de-energized.
PRECAUTIONS AND GENERAL INFORMATION WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated electrical components must be performed by a factory authorized technician. DO NOT open any access panel which requires the use of tools. Failure to follow this warning can result in severe electrical shock. CAUTION: RISK OF DAMAGE DO NOT connect or energize this appliance until all installation instructions are read and followed.
INSTALLATION UNPACKING & INSPECTION Carefully remove the appliance from the carton. Remove all protective plastic film, packing materials and accessories from the Appliance before connecting electrical power or otherwise performing any installation procedure. Carefully read all instructions in this manual and the Installation Instruction Sheet packed with the appliance before starting any installation. Read and understand all labels and diagrams attached to the appliance.
INSTALLATION (continued) WARNING: EQUIPMENT SET-UP ELECTRIC SHOCK HAZARD 1. IF CONVECTION OVEN IS TO BE USED FOR PROTEINS, INSTALL EXTERNAL DUCT a. Remove two screws at each end of adapter plate on back of oven. b. Loosen two screws at bottom of adapter plate. Remove adapter plate. c. Slide bottom flange of vent duct over the two loosened screws. D. Install four and tighten screws at ends of vent duct, then tighten bottom screws.
INSTALLATION (continued) DANGER: ELECTRICAL SHOCK HAZARD ELECTRICAL CONNECTIONS MUST BE MADE BY A LICENSED ELECTRICIAN Electrical shock will cause death or serious injury. CAUTION: ELECTRICAL INSTALLATION Refer to the nameplate on the front of the appliance. • Verify the ELECTRICAL SERVICE POWER. • Voltage and phase must match the nameplate specifications, and available electrical service amperage must meet or exceed the specifications listed on page 1.
OPERATION CAUTION: HOT SURFACE Exposed surfaces can be hot to the touch and may cause burns. MANUAL COOK MODE On ovens equipped with optional casters, be sure casters are locked before turning power switch ON. Configure oven racks as appropriate. Close the oven door. Cooktop has four individually controllable hotplate sections. Turn appropriate hotplate TEMP knob to energize hotplate: 1. There are an infinite number of settings between LO and HI. 2. HI is a continuous ON position. 3.
OPERATION (continued) PROGRAM COOK MODE CAUTION: Five programmable (PGM) keys are provided to allow presetting times and temperatures for commonly cooked menu items: 1. Press and hold the appropriate PGM key and turn the TEMP knob to the desired set temperature. 2. Continue to press and hold the appropriate PGM key and turn the TIME knob to the desired cook time. 3. When the PGM key is released, the current temperature and time settings are stored in memory. 4.
SUGGESTED TIMES & TEMPERATURES FOR BAKING AND ROASTING PRODUCT TEMP ºF TIME (MINUTES) NO.
CLEANING INSTRUCTIONS PREPARATION Allow oven to cool to 150ºF or less CAUTION: FREQUENCY Daily ELECTRIC SHOCK HAZARD TOOLS Fiber Brush, Plastic Scouring Pad, Plastic Scraper Mild Detergent, Conventional Oven Cleaner, Non-Abrasive Cleanser Clean Soft Cloth / Sponge Solution: 4 parts vinegar to 10 parts warm water Disconnect appliance from electric power before cleaning. CAUTION: BURN HAZARD CLEANING 1. Turn POWER SWITCH to FAN. With the door held open, allow the oven to cool.
CLEANING INSTRUCTIONS (continued) 11. Clean cooktop: DANGER ELECTRIC SHOCK HAZARD DO NOT SPRAY WATER ON OR AROUND ELECTRICAL EQUIPMENT DO NOT WASH FLOOR NEAR ELECTRICAL EQUIPMENT WITH WATER SPRAY IMPORTANT: DO NOT spill or pour water into controls, control panel or wiring. Damage to internal components from water damage is not covered by warranty. IMPORTANT: DO NOT use metal implements or steel wool to clean coil-type elements or solid plate elements.
TROUBLESHOOTING SUGGESTIONS CAUTION: ELECTRICAL SHOCK HAZARD Removal of any cabinet panel will result in exposed electrical circuits. Any procedure requiring the removal of any cabinet panel must be performed by a qualified technician only. CAUTION: ELECTRICAL SHOCK HAZARD Fuse replacement may expose dangerous voltages. Fuse replacement must be performed by a qualified technician.
PREVENTATIVE MAINTENANCE CAUTION: BURN HAZARD Allow appliance to cool completely before adjusting. HINGE ADJUSTMENT PRECAUTIONS: None FREQUENCY: Monthly, at a Minimum; or, As Needed TOOLS: Phillips (+) Screwdriver 7/16" Nut Driver 7/8" and 1-1/8" Wrenches THE FOLLOWING PROCEDURE IS TO BE PERFORMED BY QUALIFIED PERSONNEL ONLY 1. Remove bottom panel to access pivot. 2.
PARTS & SERVICE DESCRIPTION PART NO. CASTERS (Set of 4 casters) 21330 OVEN RACK Replacement 21376 PREP TOP KIT 21445 DRIP TRAY, COIL-TYPE ELEMENT 21705 LEGS, 6” Stainless Steel (Set of 4 legs) 22226 SCRAPER, CLEANING 22445 ELEMENT SUPPORT, COIL-TYPE ELEMENT 500039 CLEANING CRÈME, CERAMIC HOTPLATE 501124 IMPORTANT: Use only factory authorized service parts and replacement filters.
