011A WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only. prices charged by Wells Bloomfield for its products are based upon the limitations in this warranty.
TABLE OF CONTENTS WARRANTY FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION MAINTENANCE INSTRUCTIONS CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS WIRING DIAGRAM EXPLODED VIEW & PARTS LIST PARTS & SERVICE CUSTOMER SERVICE DATA xi 2 3 3 4 6 7 8 10 11 12 - 15 17 17 INTRODUCTION Thank You for purchasing this Wells Bloomfield appliance.
FEATURES & OPERATING CONTROLS A. THERMOSTAT INDICATOR LIGHT 1. On thermostatically controlled warmers, power is applied to the heating element according to the control knob position and the actual temperature at the temperature sensing thermobulb. 2. The desired temperature is controlled by rotating the temperature control knob. The knob has a numeric scale, where higher numbers correspond to higher temperature. 3.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments only. This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
INSTALLATION WARNING: Risk of injury Installation procedures must be performed by a qualified technician with full knowledge of all applicable electrical and plumbing codes. Failure can result in personal injury and property damage. UNPACKING & INSPECTION Carefully remove the appliance from the carton. Remove all protective plastic film, packing materials and accessories from the Appliance before connecting electrical power or otherwise performing any installation procedure.
INSTALLATION 4. For “top-mounted” warmers (i.e. warmers mounted from above the counter top): a. Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout. b. After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter c. Apply a thin bead of food-grade silicone sealant around the flange to seal it to the counter. d.
OPERATION Hot Surface Exposed surfaces can be hot to the touch and may cause burns. WET OR DRY OPERATION for WARMERS 1. Carefully read the description of the warmer operation on the specification sheet. 2. a. Most warmers are designed for WET OR DRY operation. b. Warmers may be used wet, or may be used dry. However warmers may NOT be used wet-to-dry or dry-to-wet unless they have been allowed to cool to room temperature between the change in wet or dry operation. c.
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
CLEANING INSTRUCTIONS Shock Hazard DAILY CLEANING INSTRUCTIONS PREPARATIONS: Turn control knob(s) to OFF. Allow warmer to cool before proceeding. Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Minimum - daily. TOOLS: Mild Detergent Solution: 10 Parts Warm Water to 4 Parts Vinegar Plastic Scouring Pad Clean Cloth or Sponge Food-Grade Silicone Sealant Do NOT splash or pour water into or over any control panel or wiring.
CLEANING INSTRUCTIONS WEEKLY CLEANING INSTRUCTIONS CAUTION: PREPARATIONS: CHEMICAL BURN HAZARD Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge 1. Add water to pans until water is at normal operating level (1” - 1 1/2” deep) or covers accumulated scale. 2.
TROUBLESHOOTING SUGGESTIONS TROUBLESHOOTING POSSIBLE CAUSE SUGGESTED REMEDY No power to warmer Circuit breaker off or tripped Reset circuit breaker Warmer will not heat Temperature control not set Set control to desired temperature Wet insulation Verify flange-to counter seal is sound, or reseal with food-grade silicone sealant Pan leaking or other internal damage Contact your Authorized Wells Service Agency for repairs Internal damage Contact your Authorized Wells Service Agency for repairs M
M011A 2M-308013 Owners Manual for Built-In Half Size Warmers WIRING DIAGRAM WIRING DIAGRAM TSW-6UL CONTROL THERMOSTAT 185°F 120 VOLTS SINGLE PHASE 3 HEATING ELEMENT 5 4 6 PILOT LIGHT ON/OFF SWITCH 7 VOLTS 1 120 2 120V 11 WATTS 350 AMPS 2.
EXPLODED VIEW & PARTS LIST HSW-6 and HSW-6D 1 2 3 5 6 7 M011A 2M-308013 Owners Manual for Built-In Half Size Warmers 4 8 12 9 10 13 11 Model: HSW6 & HSW6D Built-In Half Size Warmers IL2135, Rev A 12
EXPLODED VIEW & PARTS LIST Model: HSW6 Series Half Size Warmers Fig No.
EXPLODED VIEW & PARTS LIST TSW6ULD 1 2 3 8 4 6 5 9 7 10 16 6 13 12 20 22 14 17 18 25 24 M011A 2M-308013 Owners Manual for Built-In Half Size Warmers 11 19 26 15 15 23 21 27 28 Model: TSW6D Built-In Third Size Warmer w/ Fixed Thermostat IL2264, Rev - 14
EXPLODED VIEW & PARTS LIST Model: TSW6ULD Third Size Warmer M011A 2M-308013 Owners Manual for Built-In Half Size Warmers Fig No Part No Description Qty 1 P2-303017 PAN ASSY TSW-6ULD 1 2 2H-40686 INSUL SIDES HSW-6 3 3 2T-40528 THERMO CTRL HMP 1 4 2C-33961 NUT 6-32 HEX MACH SCR KEP 2 5 2N-303022UL ELEM TSW-6UL 120V 1 6 2C-31053 NUT 8-32 KEPS MS NICKEL 4 7 2C-32243 WASHER FLAT ZI #12 SAE 2 8 P2-303020 PLATE HEAT TRANSFER TSW-6 1 9 2H-40685 INSUL BOT HSW-6 1 10 P2-303
M011A 2M-308013 Owners Manual for Built-In Half Size Warmers NOTES 16
PARTS & SERVICE DESCRIPTION PART NO. IMPORTANT: Use only factory authorized service parts and replacement filters. P2-31869 For factory authorized ACCESSORIES DRAIN SCREEN OPTIONAL 72” WIRING, thermostatically controlledwarmers ** ** contact factory customer service for availability service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: Wells Bloomfield, LLC 10 Sunnen Dr., St. Louis MO 63143 USA Service Dept.
WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
