Wellgate 26xx Series VoIP Gateway User Manual Revision Information Version Date Description 106d Oct-12-2009 4nd English Version 1. Introduction ...................................................................................................... 3 1.1 26xx Telephony Gateway .................................................................................. 3 1.2 Benefits .......................................................................................................... 3 1.
6xx Technical Manual EN-V106d 2. Appearance ....................................................................................................... 6 2.1 Front Panel: LED Indicators ............................................................................ 6 2.2 Rear Panel: LED Indicators ............................................................................. 7 3. Environment Setup and IP Connection ................................................................ 9 3.1 Configuration................
26xx Technical Manual EN-V106d 3.5.6 Network Status ........................................................................................... 60 3.5.7 Version Info. ............................................................................................... 61 3.5.8 Port Status ................................................................................................. 62 3.5.8 Password.................................................................................................... 63 3.
26xx Technical Manual EN-V106d 1. Introduction 1.1 26xx Telephony Gateway The Wellgate 26xx is an 4 to 8-ports FXS/FXO VoIP gateway which includes 1-WAN/4-LAN 10/100 base-T NAT router to meet the current network environment. Field-proven quality of Voice communication and Fax transmission over IP broadband access network to makes Wellgate 26xx series to be an excellent solution for various VoIP applications. 1.
26xx Technical Manual EN-V106d 1.4 Specification IP Network connection IPv4 (RFC 791) MAC Address (IEEE 802.3) PPPoE Client (RFC 2516) DNS Client DHCP Client (RFC 2131) DHCP Server (RFC 2131) NAT (RFC 1631) TCP/UDP (RFC 793/768) ICMP (RFC 792) RTP/RTCP (RFC 1889/1890) SNTP (RFC 2030) TFTP Client Telnet Server HTTP Server QoS – 802.
26xx Technical Manual EN-V106d G.711 pass-through T.38 Fax relay protocol Tone Generation & Detection Ringing Tone Ring Back Tone Dial Tone Programming Tone Call Features Call Hold Call Transfer (Blind & consultant) Call Forward (Unconditional / No Answer / Busy) MWI – Message Waiting Indication PSTN Routing Prefix (2644 only) PSTN Bypass when network or system failure (2644 only) IP line hunting Adjustable volume level Security HTTP 1.
26xx Technical Manual EN-V106d Storage Temp. & Humidity Temp.: 0℃～55℃ (32℉～131℉) Humidity: 10％～95％ relative humidity, non-condensing AC Power Adaptor: INPUT: AC100V-240V, 50/60Hz OUTPUT: DC 12V, 3.0A Regulatory Compliance: FCC (Part 15, Class B) & CE 2. Appearance 2.1 Front Panel: LED Indicators Wellgate 2608 Wellgate 2680 Wellgate 2644 LED Description Power When the power adapter is connected, the LED will light up green.
26xx Technical Manual EN-V106d LAN (1-4) This will light up green when the gateway’s LAN port 1-4 is physically connected to a local network (Refer to Rear Panel section in page number for location of LAN port 1-4). When data is transmitted through this port, it will flash green. The default IP of LAN port is 192.168.123.123. T1-T8 The status LED for FXS port 1-8, this will light up amber orange when the connected phone’s handset is lifted, or when the connected phone is engaged in a conversation.
26xx Technical Manual EN-V106d line in PABX. L1-L8 The RJ-11 FXO port 1-8, connect to PSTN T1/P1-T4/P4 It is a pair of FXO and FXS connector. The different is that the when power off or application is crashed, the FXO and FXS will be connected together automatically for local surviving. LAN 1-4 10/100 Base-T RJ-45 socket for LAN port 1-4, connects to local area network. WAN 10/100 Base-T RJ-45 socket for WAN port, connects to wide area network.
26xx Technical Manual EN-V106d 3. Environment Setup and IP Connection First of all, connect your computer to Wellgate 26xx’s LAN port by using DHCP. The IP address assign to your computer should be 192.168.123.x by default. Once you can get the IP address from Wellgate 26xx, you can start the configuration as below. 3.1 Configuration Login to the WELLGATE 26XX web configuration menu 1. Open your WEB browser and key in the default IP address of the gateway (http://192.168.123.
26xx Technical Manual EN-V106d 2. You will enter the main page of the web configuration interface after you keyed in the username and password correctly (see figure below).
26xx Technical Manual EN-V106d 3.2 Network Configuration The following instructions will explain the configurations for setting up the WAN port of the 26xx. There are in total three methods of connections: Static IP, DHCP and PPPoE. Note: You can retrieve the IP address of the WAN port by keying #126# on the phone set that is connected to the FXS port of the gateway. You will hear an IVR announcing the current IP address of the WAN port.
26xx Technical Manual EN-V106d 3.2.1 WAN Setting The table shown below describes the configuration items for 3 connection types of network (Static IP, DHCP and PPPoE).
26xx Technical Manual EN-V106d WAN Setting Item Description Connected mode Select the connection method for the WAN port of the 26xx, you can choose the following: Static IP DHCP PPPoE Current IP Address Show current IP address DNS server mode Select the DNS behavior, you can choose the following: Auto Manual “DNS auto” will retrieve the DNS information sent from Static IP DHCP PPPoE V V V V V V V V V V V V V V V V V V V V V the DHCP server.
26xx Technical Manual EN-V106d WAN Setting Item Description Default gateway Specify the IP address of the default gateway. Remote access Restricts/Blocks users restriction connecting to the WAN port’s IP remotely, you can Enable/Disable this option. PPPoE userID Specify the username of the PPPoE account V PPPoE password Specify the password associated to the PPPoE account above.
26xx Technical Manual EN-V106d 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes. 3.2.1.2 WAN Setting --DHCP 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes. P.S. When you are using DHCP in WAN and not connected, please make sure you connect Ethernet before use PC to connect to LAN port.
26xx Technical Manual EN-V106d 3.2.1.3 WAN Setting --PPPoE 1. Input PPPoE user ID and password 2. Press the “Apply” button (at the bottom) after you finish to save changes. 3. Press the “CANCEL” button (next to the Apply button) to clear the values in the page. 4. Press the “Reboot” button to apply the changes.
26xx Technical Manual EN-V106d 3.2.2. LAN Setting LAN Setting ITEM Description LAN IP address Specify the IP address of the 26XX LAN port. LAN mask address Specify the mask address for 26XX LAN port. DHCP server Enable/Disable DHCP function on the LAN port. Once enabled, the LAN ports will function as a DHCP server, network devices connected to them will be issued with IP addresses.
26xx Technical Manual EN-V106d LAN Setting ITEM Domain Name Description You can specify the domain name that will be assigned by the DHCP server to the attached network devices. The DHCP server will send information on the “server host name” to the DHCP client. Lease time(sec) You can specify the maximum lease time of the IP address allocated to the DHCP client.
26xx Technical Manual EN-V106d 3.3 General configuration To make VoIP calls, you will need a SIP account provided by the SIP Proxy you are registered with. To configure the relevant SIP settings, please refer to the instructions explained below. 3.3.1 PABX Mode (Just use 2644 only) This quick setting is dedicated to be used for Wellgate 2644 to become a inter-connection in between PSTN and traditional PABX. The call scenario will be working as below: 1.
26xx Technical Manual EN-V106d PABX Connection To enable PABX behavior or not. SIP Setting Please refer to 3.3.2.1 Representative Number Configuration It is used when you only have a SIP account to be shared for FXS lines. Please refer to 3.3.2.1 Primary FXS SIP settings When you have multiple SIP accounts for each FXS line, please set Representative Number Only to No. Then refer to 3.3.2.
26xx Technical Manual EN-V106d Primary proxy Specify the data of primary proxy: Enable/Disable, IP address, Port#, Domain Name, Expire time and MWI TTL. Secondary proxy Specify the data of secondary proxy: Enable/Disable, IP address, Port#, Domain Name, Expire time and MWI TTL. When you enable secondary proxy, it will start to register no matter whether primary proxy is registered or not. However, it will be used only when primary proxy is not registered or the incoming call is coming from it.
26xx Technical Manual EN-V106d when the specified forward condition is met. Ring Type Select the Ring Type of representative number. You can choose the following: Serial ring (Follow the ring priority defined below) Simultaneous(ring all) Ring Time (s) for Serial ring Specify the Ring Time for Serial ring Status Displays the registration status, whether it is registered or not. Hunting Select the group of representative number, and specify the priority.
26xx Technical Manual EN-V106d 3.3.3 SIP Advanced Setting Local SIP port(1~65535) Specify the local starting SIP port. Each account’s interval is 2. For example, the local SIP port is set to 5060. The following is the port number to be used for 26xx: Port 1: 5060 Port 2: 5062 Port 3: 5064 Port 4: 5066 Port Port Port Port 5: 6: 7: 8: 5068 5070 5072 5074 Representative Number: 5076 Local RTP port(1~65535) Specify the local starting RTP port number.
26xx Technical Manual EN-V106d Session Expire(Sec) Specify the session expire time that will be used to negotiate with the remote host or proxy. Min Session Expire(Sec) Specify the minimum session expire time that other host or proxy will need to follow when calling the WELLGATE 26XX.
xx Technical Manual EN-V106d destination. Support Message Waiting Indication (MWI) You can Enable or Disable the MWI function.( This feature is for FXS only) SIP Message Resend Timer Base (sec) Specify the resend time in seconds for each SIP request message that has not received a response. Max. Response Time for Invite Specify the timeout period for SIP (1~30sec) Invite messages.
26xx Technical Manual EN-V106d 3.3.4 Payload Type Setting RFC2833 payload type Specify the RFC2833 payload type (range is 96~128, however 100, 102~105 is reserved by other payload types). FAX bypass payload type Specify the FAX payload type (range is 96~128, however 100, 102~105 is reserved by other payload types) Modem by pass payload type Specify the Modem by pass payload type (range is 96~128, default value is 103. 100, 102, 104, 105 is reserved by other payload types). 1.
26xx Technical Manual EN-V106d 3.3.
26xx Technical Manual EN-V106d No Answer Forward Time (FXS only) If you enable the No Answer Forward function (Representative number or L1~L8 number), please specify the time of no answer. The default setting is 180 sec. FAX Enable/Disable FAX T.38 function. Line1~Line8 relevant data Type Displays the port type of that particular line. Enable Enable the line or not Reg Register or Unregister to SIP Proxy Number Displays the line numbers that specified in SIP Setting.
26xx Technical Manual EN-V106d Proxy registration account ID. Display name: Specify the Display name of the phone number. The first is the number registers to Primary proxy. The default setting is 1000~1007. Enable Hotline Click the check box to enable hotline feature. If enabled, The check box will display as . Hotline Number Specify the number to forward the call to when the Hotline feature is enabled. Wait to Hotline(sec) Specify the time (sec) for wait to hotline, the default value is 0.
26xx Technical Manual EN-V106d 3.3.6 Qos Setting Type Select Qos Type: DSCP or ToS Differentiated Services Code Point Setting (DSCP) DSCP RTP Select the DSCP value for RTP (voice packets), the value in the drop down list is expressed in binary format, you can choose to meet your network environment. DSCP Signal Select the DSCP value for SIP message, the value in the drop down list is expressed in binary format, you can choose to meet your network environment.
26xx Technical Manual EN-V106d choose to meet your network environment. 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes. 3.3.
26xx Technical Manual EN-V106d 3.3.8 Caller ID Setting Caller ID Setting (Line 1~Line 8) Select the (Line 1~Line 8)Caller ID generation type to use, you can choose the following: Disable DTMF FSK(Bellcore) ETSI(Before Ring) ETSI(Between ring) FXO only choose Enable/Disable the caller ID detection AUTO: You can choose different caller ID type by line.
26xx Technical Manual EN-V106d the other lines will set the same type automatically. The “Disable” option will allow you to disable this particular function. DTMF Caller ID Start Symbol Specify the DTMF Caller ID Start Symbol The default symbol is D. DTMF Caller ID End Symbol Specify the DTMF Caller ID End Symbol The default symbol is C. 1. 2. Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes.
26xx Technical Manual EN-V106d 3.3.9 CDR Setting CDR mode Select the CDR mode for Enable or Disable. If you Enable this feature, please specify the CDR Server address and port number at the CDR server address and port’s text box, then you can get Call Detail Data form CDR Server. CDR Server address If you Enable the CDR mode, please specify the IP address of CDR Sever for data storage. CDR Server port 1. 2. Specify the CDR Server port number, The default port number is 514.
26xx Technical Manual EN-V106d enable syslog server from settings before you can use it. 3.3.10 Syslog Setting This syslog is used to send the debug log from Wellgate 26xx to syslog server.
26xx Technical Manual EN-V106d Syslog mode Select the Syslog mode for Enable or Disable. If you Enable this feature, please specify the Syslog Server address and port number at the Syslog server address and port’s text box, then you can get detail system log from Syslog server. Syslog Server address If you Enable the Syslog mode, please specify the IP address of Syslog Sever for data storage. Syslog Server port 1. 2. Specify the Syslog Server port number, The default port number is 514.
26xx Technical Manual EN-V106d 3.4 Advanced Configuration 3.4.1 System setting prack PRACK is defined in RFC 3262: Reliability of Provisional Responses in SIP. You can accommodate your softswitch (Proxy Server) to Enable or Disable this feature. ROH (FXS only) Receiver-Off-Hook (ROH) Tone A ROH tone is sent to the subscriber to inform him that his receiver is off-hook. You can Enable/Disable this option. Send billing signal (FXS only) Enable Polarity Reversal for FXS as billing signal or not.
26xx Technical Manual EN-V106d Buffer, Datagram…) indicated in T.38 Re-Invite with Session Description Protocol (SDP). You can Enable/Disable this option. FAX redundancy depth Specify the resend times (0~3)for FAX error packet, T.38 FAX Type Select the FAX Type to use, you can choose the following: T.38 T.30 FAXByPass Codec ByPass Auto Select the FAX ByPass Codec to use, you can choose the following: G.711 a-law G.
26xx Technical Manual EN-V106d system will end the dial and send out the DTMF. The limitation range is 1~5sec. FAXByPass Keyword Some SIP Proxy need specify special keyword for FAXByPass function. Input the data as SIP Proxy required. FAXByPass Keyword Some SIP Proxy need specify special keyword for FAXByPass function. Input the data as SIP Proxy required.
26xx Technical Manual EN-V106d Ring Time Limit ( 10~600sec ) (FXS only) Specify the limitation of Ring time for incoming call, when the ring is over the limit, system will drop the call. The default range is 10~600sec. Disconnect Singal Detcetion Disable Polarity Reversal When enable the Polarity Reversal Detection, WG26xx (FXO) will use the polarity reversal as the answer signal and polarity normal as the hang-up signal for FXO outgoing call.
26xx Technical Manual EN-V106d 3.4.2 SNTP Setting SNTP mode Select the SNTP mode : On or Off SNTP server address Specify the SNTP server address for time synchronization. Time Zone -GMT Select the Time Zone of your location Time setting You can specify the time with year/month/date /hour/minute /second when you select the SNTP mode with “Off”. 1. 2. Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes.
26xx Technical Manual EN-V106d 3.4.3 Codec Setting Codec Priority You can specify the priority of the codec from First to Fifth (first being the highest priority and Fifth being the lowest).
26xx Technical Manual EN-V106d G726 Bandwidth Required 1. 2. 20,40,60 When you select the codec packet size shown above, system will set default requirement of bandwidth. Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes.
26xx Technical Manual EN-V106d 3.4.4 Voice Setting Jitter Buffer Minimal Delay Specify the minimal delay of the jitter buffer. The range is 0~150 ms and the default setting is 0 ms. Maximal Delay Specify the maximal delay of the jitter buffer. The range is 0~200 ms and the default setting is 200 ms. OPTFactor Specify the dynamic jitter buffer frame error/delay optimization factor, the range is 0~13. VAD Enable/Disable the VAD (Voice Activity Detection) feature.
26xx Technical Manual EN-V106d the local side (+5~-20 db, default is -3 db). Remote receive volume Specify the volume gain of the voice in the remote side (+5~-20 db, default is -3 db, default is -3 db). DTMF volume Specify the volume gain of the DTMF (+3~-32 db, default is -10 db). 1. 2. Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes.
26xx Technical Manual EN-V106d 3.4.5 Tone Setting Dial tone Specify the pattern of the Dial tone, you can adjust the high frequency, low frequency, high level, low level, the On and Off time for tone 1 and 2. Ringback tone (FXS only) Specify the pattern of the Ringback tone, you can adjust the high frequency, low frequency, high level, low level, the On and Off time for tone 1 and 2.
26xx Technical Manual EN-V106d and Off time for tone 1 and 2. ROH Tone (FXS only) Specify the pattern of the ROH Tone, you can adjust the high frequency, low frequency, high level, low level, the On and Off time for tone 1 and 2. The ROH tone is a single high frequency tone used to warn users that their phone is not placed on-hook (hang up) correctly.
26xx Technical Manual EN-V106d 3.4.6 Phone Setting Primary Ringing Ringing Frequency Specify the Ringing frequency value. ringing frequency : 15~100 (Unit : Hz) Ringing ON Specify the Ringing ON value. ringing ring ON : 0~8000 (Unit : ms) Ringing OFF Specify the Ringing OFF value. ringing ring OFF : 0~8000 (Unit : ms) Ringing level Specify the ringing level. ringing level : 0 Flash low ~ 94 (Unit : V) Specify the value of the flash (low). : 60~2000 (Unit : ms).
26xx Technical Manual EN-V106d will be handled as hang-up. Secondary Ringing (FXS only) Note: The feature will be enabled automatically when the Min. Digit Count has been enabled and specified. It is used to have different ring cadence when the incoming caller number is shorter than the setting of “Min. Digit Count” Ringing Frequency Specify the Ringing frequency value. ringing frequency : 15~100 (Unit : Hz) Ringing ON Specify the Ringing ON value.
26xx Technical Manual EN-V106d 3.4.7 Digit Manipulation Digit Manipulation Editor FXO: This DM group is used for FXO incoming call. FXS: This DM group is used for FXS dialing out. VOIP: This DM group is used for VOIP incoming call. 1-4: These DM groups can be used for routing table. Matched Prefix: The prefix to be matched length for DM. The longest prefix will be matched first. Matched min Length: Set to 0 for ignoring the length.
26xx Technical Manual EN-V106d 886 0 2 5 002 8862123456 8800223456 886 0 30 30 002 8862123456 8862123456002 886 0 1 6 8862123456 83456 Note: The DM Group 1~4 can have the feature to delay the dialing by added a “p” into the replace value. It might be useful, if you want to wait for a while and dial the second part of DTMF for calling out. Each “p” represents 2 seconds delay. For example: 822265699ppp1234; it will first dial 82265699 and wait to 6 sec to dial 1234. 1. 2.
26xx Technical Manual EN-V106d 3.4.8 Dial Plan Dial Plan Editor Using this feature, users can specify the number that will be immediately dialed out without having to press the “#” (at the end of the dialed number) on the keypad or until the dial time timeout period. The number can be specified depending on the length of the dialed number, or the prefix of the dialed number.
26xx Technical Manual EN-V106d Leading digit: Total digit count: 8 If the user dials an 8 digit number (e.g. 82265699), the WELLGATE 26XX will immediately detect it and dial this number straight away. Third Example Function: Disable Leading digit: 02 Total digit count: 10 If the user set the Function parameter as “Disable”, the call number with a length of 10 digits and a prefix of 02 will proceed as normal.
26xx Technical Manual EN-V106d 3.4.9 Call routing Editor Call Routing Status: enable or disable this routing Prefix: matched DNIS (called number) prefix. Min Length: matched DNIS minimum length. This DM can only be executing when the received DNIS is longer than it. Route to: The outgoing call type could be (FXO / FXS / VOIP /P2P ) Backup route to: If primary route is unable to reach the destination, whether to use the backup routing or not.
26xx Technical Manual EN-V106d 3.5 Management 3.5.1 Provision Server Note: The provisioning server is supported by working with WellEMS 9510 only. . If you need this requirement, Please contact Welltech for availabilities. Provision server Mode Enable/Disable provision function Provision server IP address Specify the Provision Server’s IP address. Provision server port Specify the Provision server port Provision cycle time Specify the cycle time of the provisioning.
26xx Technical Manual EN-V106d 3.5.2 Save-Reload setting Export File Click the “Export” button to export “user.cfg” data Import File Specify the file path and file name to Import the configure data. 1. Press the “Reboot” button to apply the changes.
26xx Technical Manual EN-V106d 3.5.3 Voice File Voice File Type Voice files type to be uploaded. It could be greeting or hold tone. Upload File Specify the file path and file name to upload. Please make sure that the file format needs to be G.711U, 8K, 8 bits raw file.
26xx Technical Manual EN-V106d 3.5.4 Upgrade Firmware Http Upload Specify the location of the firmware for uploading through Http. 1. Under Device Management => Software Upgrade web menu, specify the location of the firmware by clicking the Browse button next to the Http Upload 2. 3. 4. 5. text box. You will be prompted with a window requesting the location of the firmware. Locate the firmware that is stored in your hard drive. Once located, click the Open button.
26xx Technical Manual EN-V106d 3.5.5 Reset to Default Users can restore back to factory default settings using this feature. The password of the account and the network configurations are the things that will not be changed when this feature is executed.
26xx Technical Manual EN-V106d 3.5.6 Network Status Connection mode Displays the current connection mode. Current IP address Displays the current IP address of the WAN port. Subnet mask Displays the current subnet mask’s IP. Default gateway Displays the current default gateway’s IP. Primary DNS address Displays the current primary DNS address. Second DNS address Displays the current secondary DNS address. WAN MAC Displays the MAC address of the WAN port.
26xx Technical Manual EN-V106d 3.5.7 Version Info. Boot version Displays the current boot version loaded on the WELLGATE 26XX. Post version Displays the current post version loaded on the WELLGATE 26XX. Application version Displays the current application version loaded on the WELLGATE 26XX.
26xx Technical Manual EN-V106d 3.5.8 Port Status Refresh Interval Time to update the status Item Displays the corresponding port number. Port Type Displays the port type (FXS, FXO) of the corresponding port number. Enable Whether the port is enabled or disable. Plug Whether PSTN is connected to the FXO port or not Status Displays the status of the port. Status Time Status updated time Register Proxy Displays the registration status of the corresponding port number.
26xx Technical Manual EN-V106d 3.5.8 Password Username Select the type of user name that you would like to configure the password for, you can choose the following: root user Current password Specify the current password for the user selected in the drop down list above. New password Specify the new password for the user selected in the drop down list above. Confirm new password Repeat the new password again for confirmation. 1. 2.
26xx Technical Manual EN-V106d 3.6 Rebooting the system Executing this function will reboot the whole system, when configuration changes are made to the device, it needs to be rebooted for the changes to take effect (see figure below).
26xx Technical Manual EN-V106d Appendix A: How to set the P2P call Example1: This example shows a way to do the P2P in between a 2608 and 2680 by using the call routing features. Used IP address: 1. 2608 IP is 192.168.18.2 2. 2680 IP is 192.168.18.235 A. 2608 Configuration Step 1: Disable proxy settings and apply it as follows Step 2: Disable Register for all line and apply it.
26xx Technical Manual EN-V106d 66
26xx Technical Manual EN-V106d Step 3: Create a prefix as follow to route the call to 2680 as follows. Reboot and try it. For this example, we are route 26801 to 2680’s first line, 26802 to 2680’s second line...etc.
26xx Technical Manual EN-V106d B. 2680 configuration Step 1: Disable proxy settings as below and apply it.
26xx Technical Manual EN-V106d Step 2: Disable register for all lines as follows and apply it.
26xx Technical Manual EN-V106d Step 3: Create prefix to route to 2608’s FXS port. Reboot and try it. For this example, we are route 260801 to 2608’s first FXS line, 260892 to 2608’s second FXS line...etc.
26xx Technical Manual EN-V106d Example 2: This configuration shows an example to use the hot line for p2p calling. It is useful when you want your FXS pickup a phone and calling to a predefined destination. A. 2608 configuration Step 1: Disable proxy settings and apply it.
26xx Technical Manual EN-V106d Step 2: For the line need to do the P2P hot line, put hotline number as the format of “number@uri:port”. Apply and reboot it. In this example, when FXS line 1 pickup the phone, it will be hot line to 26801@192.168.18.235:5060. Line 3 will be route to 26803@192.168.18.235:5060.
26xx Technical Manual EN-V106d B. 2680 configuration Step 1: Disable proxy settings and apply it.
26xx Technical Manual EN-V106d Step 2: For the line need to do the P2P hot line, put hotline number as the format of “number@uri:port”. Apply and reboot it. In this example, when FXO line 1 receives an incoming call, it will be hot line to 260801@192.168.18.2:5060. Line 3 will be route to 260803@192.168.18.2:5060.
26xx Technical Manual EN-V106d Example 3 This configuration shows an example for P2P calling to a representative number. When a PSTN call is coming to 2680 FXO port, it will start the call routing and make the p2p call to the representative number of 2608 which provides serial line hunting. The same as 2608 to route to 2680’s representative number. A. Configuration 2608 Step 1: Check the primary proxy and representative number enable option, then setup the required parameters of the representative number.
26xx Technical Manual EN-V106d Step 2: Disable SIP registers for all lines and apply it.
26xx Technical Manual EN-V106d Step 3: Create a call routing entry for routing to 2680’s representative number as below. Reboot it to take effective. In this example, the call will be route to 26800@192.168.18.235:5076 (5076 is the port number or representative listened).
26xx Technical Manual EN-V106d B. 2680 Configuration Step 1: Check the primary proxy and representative number enable option, then setup the required parameters of the representative number. Apply it. Since the P2P call will be used for this representative number, uncheck the primary proxy and apply it.
26xx Technical Manual EN-V106d Step 2: Disable sip register for all lines and apply it.
26xx Technical Manual EN-V106d Step 3: Create a call routing entry for routing to 2608’s representative number as below. Reboot it to take effective. In this example, the call will be route to 260800@192.168.18.2:5076 (5076 is the port number or representative listened).
