Website:www.wellfor.com Customer Service:206.809.0093 Email: service@wellfor.
We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. WELLFOR accepts no liability for any damage to the plumbing, floor, walls, tub, or for personal injury during installation.Please observe all local plumbing and building codes. ·Ensure that you have gathered all the required materials that are needed for the installation.
INSTALLATION STEPS WHEN USING A HEAD SHOWER IT NEEDS TO BE CONNECTED TO THE TOP OUTLET PAGE 2 For customer support,please call WELLFOR (+1)206-809-0093 or Email us at service@wellfor.
pressure balanced diverter valve valve face plate with seal joint Diverter knob kit trim cap set screw sliding bar kit with flexible hose flexible hose hand shower holder hand shower shower arm and flange kit shower head PAGE 3 For customer support,please call WELLFOR (+1)206-809-0093 or Email us at service@wellfor.
1. The size of the embedded box that needs to be drilled is 5.3"×6.7". 2.The depth of the embedded box is 1.8"-2.2". It's better to drill the depth of 1.8" for blank wall. PAGE 4 For customer support,please call WELLFOR (+1)206-809-0093 or Email us at service@wellfor.
1.Connect valve body to water supplies using the proper fitting(copper tubing, iron pipe or Pex). If either of the two outlet ports is to be unused, seal the port with a pipe plug. Note: (1) is the cold inlet port and (2) is the hot inlet port. (2) (1) 2. For copper pipe soldering joint, you need to remove the plastic covers(3) and (4) and valve cartridge from the valve body first. Avoiding soldering at high temperatures. Component of the rough could become damaged.
4. Remove the valve cartridge(5) from the valve body. (5) 5. Soldering copper pipes to brass valve, then flush the system of debris for 30 seconds. 6. After flushing, install the cartridge and bonnet nut. Make sure the cartridge is fully engaged with the slot and holes in the brass valve body. PAGE 6 For customer support,please call WELLFOR (+1)206-809-0093 or Email us at service@wellfor.
1.After the pipe connection is completed, open the protective panel and cover, and then open the cartridge,flush the pipe; then close the cartridae to check the pressure resistance and sealing performance of the pipeline, make sure there are no leakage. 2.Block each outlet pipe with a stopper then open the cartridge to check if the pipe joint is well sealed and the pipe condition under pressure to ensure no leakage.
Use a parallel ruler to measure the flatness of the embedded box casing and the vertical wall surface. If the wall surface is not flat, it should be patched to ensure the embedded box casing and vertical wall angle meets at nearly ideal angle of 90, then lay the tile decoration. PAGE 8 For customer support,please call WELLFOR (+1)206-809-0093 or Email us at service@wellfor.
1. Take off the protective panel and cover. 2.The decorative panel and the handle are connected to the control valve as shown below sequence. 3.According to the figure below, please correctly adjust the direction of water separator handle. PAGE 9 For customer support,please call WELLFOR (+1)206-809-0093 or Email us at service@wellfor.
NPT PAGE 10 For customer support,please call WELLFOR (+1)206-809-0093 or Email us at service@wellfor.
PAGE 11 For customer support,please call WELLFOR (+1)206-809-0093 or Email us at service@wellfor.
lf the cartridge is worn out which cause leakage,please turn off the water source.Remove the handle, panel, and decorative cover in sequence,remove the gland with a wrench, then take out the cartridge and copper sleeve. Repair or replace the new cartridge, then install it again in sequence. In order to keep the faucet appearance smooth and good performance,please follow the below steps to clean and maintain the faucet. 1.Clean with water and dry with a soft cotton cloth. 2.
