JOYCE ČR, s.r.o., Venhudova 6, 614 00 Brno, ČR, IČ: 25317571, DIČ: CZ25317571, Tel.: +420 539 088 010 Fax: +420 539 088 000, E-mail: joyce@joyce.cz, Web: www.joyce.cz, www.joyce-energie.cz WELL W52P IP DECT Phone User Guide Version 1.
Copyright Copyright © 2013 YEALINK NETWORK TECHNOLOGY CO., LTD. Copyright © 2013 Yealink Network Technology CO., LTD. All rights reserved. No parts of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, photocopying, recording, or otherwise, for any purpose, without the express written permission of Yealink Network Technology CO., LTD. Under the law, reproducing includes translating into another language or format.
Part 15 FCC Rules This device is compliant with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Class B Digital Device or Peripheral This equipment is tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RF exposure guidelines. Information for DECT Product This telephone is compliant with the DECT 6.0 standard which operates in the 1.92GHz to 1.93GHz frequency range. Installation of this equipment is subject to notification and coordination with UTAM. Any relocation of this equipment must be coordinated through and approved by UTAM. UTAM may be contacted at 1-800-429-8826.
GNU GPL INFORMATION W52P firmware contains third-party software under the GNU General Public License (GPL). Yealink uses software under the specific terms of the GPL. Please refer to the GPL for the exact terms and conditions of the license. The original GPL license, source code of components licensed under GPL and used in Yealink products can be downloaded from Yealink web site: http://www.yealink.com/GPLOpenSource.aspx?BaseInfoCateId=293&NewsCateId=293&CateId=293. Version 1.
User Guide W52P IP DECT Phone About This Guide The WELL W52P IP DECT phone is a full-featured mobile device, which can provide reliable and convenient wireless voice communications. In addition, it provides many widely accepted benefits of the DECT standard, including high security, scalability, and low power consumption to better meet your requirements. This guide provides everything you need to quickly use your new phone.
About This Guide vii
User Guide W52P IP DECT Phone Table of Contents About This Guide .................................................................. lxxvii In This Guide .......................................................................................................................... lxxvii Table of Contents .................................................................. lxxix Getting Started ............................................................................ 1 Packaging Contents .....................
Table of Contents Phone Settings ........................................................................... 22 Handset Name .........................................................................................................................23 Language ..................................................................................................................................23 Ring Tones .............................................................................................................
User Guide W52P IP DECT Phone Answering Calls ........................................................................................................................49 Ending Calls ...............................................................................................................................50 Redialing Calls ..........................................................................................................................50 Call Mute ................................................
Table of Contents xi
Getting Started Getting Started This chapter provides basic installation instructions and information for obtaining the best performance with the W52P IP DECT phone. The topics include: Packaging Contents Connecting the W52P Base Station Setting up the W52P/W52H Handset Setting up the Charger Cradle Charging the Handset If you require additional information or assistance with your new phone, contact your system administrator.
User Guide W52P IP DECT Phone W52P/W52H Handset Charger Cradle Power Adapter Two Rechargeable Batteries 2
Getting Started Ethernet Cable Belt Clip Quick Installation Guide & Quick Reference Guide CD-ROM Check the list before installation. If you find anything missing, contact your system administrator. Connecting the W52P Base Station You have two options for power and network connection of the base station. Your system administrator will advise you which one to use. AC power Power over Ethernet (PoE) Note Please pay attention to the range of the base station.
User Guide W52P IP DECT Phone AC Power To connect the AC power: 1. Connect the DC plug on the power adapter to the DC5V port on the base station and connect the other end of the power adapter into an electrical power outlet. 2. Connect the supplied Ethernet cable between the Internet port on the base station and the Internet port in your network or the switch/hub device port. Power over Ethernet Using a regular Ethernet cable, the base station can be powered from a PoE (IEEE 802.
Getting Started Setting up the W52P/W52H W52P/W52H Handset To insert batteries into the handset: 1. Open the battery cover. 2. Insert the batteries in the correct polarity. 3. Close the battery cover. Note Do not short-circuit the batteries, as short-circuiting the terminals may damage the batteries or the handset. Do not use damaged batteries, as using damaged batteries may cause an explosion. Battery Information Technology: Nickel Metal Hydride (NiMH) Size: AAA Voltage: 1.
User Guide W52P IP DECT Phone Charging the Handset To charge the handset: 1. After setting up the handset and charger cradle, place the handset in the charger cradle. The original handset included in the W52P package is pre-registered to the base station. After charging, the handset is ready to use.
Overview Overview This chapter provides the overview of the W52P IP DECT phone. The topics include: Base Station Description Handset Description Displaying Information on LCD Screen Icon Instructions If you require additional information or assistance with your new phone, contact your system administrator. Base Station Description After the base station starts up successfully and the handset is registered to the base station, all LEDs on the base station illuminate solid green.
User Guide W52P IP DECT Phone Item Description Indicates the network status. ③ Network Status LED Slow flashes green when the network is unavailable. Illuminates solid green when the network is ready. Indicates the power status of the base station. Slow flashes green when the base station is during the firmware upgrading process. ④ Power Indicator LED Slow flashes green when the base station is during the resetting process. Illuminates solid green when the base station is powered on.
Overview Hardware component instructions of the W52P/W52H handset are: Item ① Earpiece ② LCD Screen ③ Soft Keys Description Outputs audio during the earpiece call. Shows call information, handset status icons, prompt messages and so on. Label automatically to identity their context-sensitive features. Switches between the earpiece and speakerphone ④ Speakerphone Key modes. Answers an incoming call. ⑤ Headset Connector Connects a headset. Answers an incoming call.
User Guide W52P IP DECT Phone Displaying Information on LCD Screen The idle screen may be shown as below: Status Line Text Line Soft Key Line The LCD screen is divided into three parts: status line, text line and soft key line. The information shown in the status line: On hook (idle) — displays signal strength indicator, internal handset number and battery status. Off hook — displays line ID.
Overview Icon Instructions Icons appear on the LCD screen are described in the following table: Icon Description Anonymous Call Anonymous Call Rejection Missed Call Voice Mail Keypad Lock Silent Mode Do Not Disturb Call Forward Call Hold Call Mute Unassigned Outgoing Line Unusable Line Loudspeaker On Headset Mode On 11
User Guide W52P IP DECT Phone 12
Basic Operations Basic Operations This chapter provides you with the basic operating instructions of the W52P IP DECT phone. The topics include: Handset Registration Basic Network Settings Checking System Status Account Registration Checking Line Status Turning Handset On/Off Adjusting Ringer Volume Locking/Unlocking Keypad Locating a Handset Switching Silent Mode On/Off Menu Guidance If you require additional information or assistance with your new phone, contact your system administrator.
User Guide W52P IP DECT Phone The handset plays a warning tone and prompts the message “Handset Subscribed” on the LCD screen, which indicates the registration has finished. After successful registration, the internal handset number and handset name appear on the LCD screen. To de-register a handset: 1. Press to enter the main menu. 2. Select 3. Enter the system PIN (default: 0000). 4. Press the Done soft key. ->Registration->De-reg. Handset.
Basic Operations 4. Press the Done soft key. 5. Press 6. Enter the valid values in the IP Address, Subnet Mask, Default Gateway, Primary DNS or to select Static from the IP Address Type field. and Secondary DNS fields. 7. Press the Save soft key to accept the change. If you are using an xDSL modem, you can connect your base station to the Internet via PPPoE mode. The PPPoE port will perform a PPP negotiation to obtain the IP address.
User Guide W52P IP DECT Phone To check the network status: 1. Press 2. Select to enter the main menu. ->System Status. The LCD screen displays the general information and the More… option. 3. Select More …->Network. The LCD screen displays the network status. 4. Press or to scroll through the list and view the specific information. To check the handset status: 1. Press 2. Select to enter the main menu. ->System Status. The LCD screen displays the general information and the More… option. 3.
Basic Operations Checking Line Status You can register up to 5 lines to one base station. The status of each registered line can be checked using the menu of the handset. To check the line status: 1. Press 2. Select to enter the main menu. ->Line Status. The LCD screen displays all lines registered to the base station with icons for indicating line status. For example, the icon in the bottom of a line indicates that the handset has no privilege to place a call using this line.
User Guide W52P IP DECT Phone Locking/Unlocking Keypad You can lock the handset keypad to prevent keys from being accidentally pressed. To lock the keypad: 1. Long press when the handset is idle until the LCD screen prompts the message “Keypad Locked, Press and hold ‘#’ to unlock!”. The keypad is locked and the icon appears on the idle screen. You can still answer or reject incoming calls as usual. You can also end the answered call by pressing . To unlock the keypad: 1.
Basic Operations To switch the silent mode on: 1. Long press until the LCD screen prompts the message “All Ring Tones Off”. The silent mode is on. The icon appears on the idle screen. To switch the silent mode off: 1. Long press again until the LCD screen prompts the message “All Ring Tones On”. icon disappears from the idle screen. The silent mode is off. The Menu Guidance The handset provides a variety of features that are grouped into menu.
User Guide W52P IP DECT Phone 20
Basic Operations To access a submenu feature: 1. Press 2. Press or to highlight the desired submenu. or the OK soft key to access the next menu level. You can cancel the current operation and return to the previous menu level by pressing or the Back soft key. Returning to Idle Screen To return to the idle screen: 1. Long press to quickly exit the menu and return to the idle screen.
User Guide W52P IP DECT Phone Phone Settings This chapter provides you with some instructions to change the settings of your phone.
Phone Settings Handset Name The handset will be assigned a name by default if successfully registered to the base station. You can personalize the handset name. To rename the handset: 1. Press to enter the main menu. 2. Select 3. Edit the current value in the Rename field. 4. Press the Save soft key to accept the change. ->Handset Name. Language The handset supports displaying text in different languages. The default language of the handset is English.
User Guide W52P IP DECT Phone You can also enter the menu ->Audio->Ring Tones->Volume, press or to decrease/increase the ringer volume. Advisory Tones Advisory tones are acoustic signals of your handset, which inform you of different actions and states. The following advisory tones can be configured independently of each other: Keypad Tone: plays when a user presses any key of the keypad. Confirmation: plays when a user saves settings or places the handset in the charger cradle.
Phone Settings Screen Saver You can enable the screen saver to protect the LCD screen if you do not use your handset for a long time. The screen saver of the handset is designed to protect your LCD screen by filling it with an analog clock. When the screen saver is enabled, an analog clock will be activated and displays on the LCD screen if no user activity is sensed for approximately 10 seconds. To configure the screen saver: 1. Press to enter the main menu. 2. Select 3.
User Guide W52P IP DECT Phone To configure the notification light: 1. Press 2. Select 3. Press to enter the main menu. ->Display->Notification Light. or to select the desired value from the Voice Mail field. If Enabled is selected, the message key LED flashes red when the handset receives a new voice mail. 4. Press or to select the desired value from the Missed Call field. If Enabled is selected, the message key LED flashes red when the handset receives a new missed call. 5.
Phone Settings To configure the time format: 1. Press 2. Select 3. to enter the main menu. ->Display->Time Format. Press or to highlight the desired time format, and press the Change soft key. The radio box of the selected time format is marked. The format of the display time on the LCD screen will be changed accordingly. To configure the date format: 1. Press 2. Select 3. Press to enter the main menu. ->Display->Date Format.
User Guide W52P IP DECT Phone Contact Management This section provides the operating instructions for managing contacts. The topics include: Local Directory Blacklist Remote Phonebook Network Directory Local Directory You can store the frequently used contacts in the handset’s local directory, where names and numbers can be freely added, deleted and edited. This allows you to make calls without having to dial the number manually.
Phone Settings To enter a character: You can press the key which contains your desired character a certain number of times to enter the character. To switch the input method: 1. Press . The current input method is indicated on the top right-hand corner of the LCD screen. For example, “ABC” represents the upper-case input method, “abc” represents the lower-case input method and “123” represents the digital input method. To make a space: 1. Press when the input method is not “123”.
User Guide W52P IP DECT Phone Note 6. Enter the name of the new entry. 7. Press the Save soft key to accept the change or the Back soft key to cancel. When you are adding a contact, both the office number and the mobile number cannot be left blank at the same time. When the contact name is left blank, the handset sets the office number or the mobile number as the contact name.
Phone Settings filtered and display on the LCD screen. To search for contacts in the local directory: 1. Press to enter the main menu. 2. Select 3. Enter a few continuous characters of the desired contact name or number using . the keypad. The contacts whose name or number matches the search will appear on the LCD screen after a timeout or when the Search soft key is pressed. You can dial a contact from the result list.
User Guide W52P IP DECT Phone To delete an entry from the blacklist: 1. Press to enter the main menu. 2. Select 3. Press 4. Press the Options soft key, and select Delete. ->Telephony->Caller Blacklist. or to highlight the desired entry. The selected entry will be deleted successfully. To delete all entries from the blacklist: 1. Press to enter the main menu. 2. Select 3. Press the Options soft key, and select Delete All. ->Telephony->Caller Blacklist.
Phone Settings 1. Press 2. Select 3. Press to enter the main menu. . or to highlight the name of your corporate directory, and press the Enter soft key. 4. Select the desired contact from the corporate directory. 5. Do one of the following: - If only one number of the contact is stored in the local directory, press to dial out the number. - If both the office number and the mobile number of the contact are stored in the local directory, press the View soft key to display the two numbers.
User Guide W52P IP DECT Phone The handset connects to load the network directory, and then displays the desired network contact list on the LCD screen. To place a call from the network directory: 1. Press 2. Select 3. Press to enter the main menu. ->Network Dir. or to highlight the desired group, and press the Enter soft key. The LCD screen displays the desired network contact list. 4. Press 6. Do one of the following: - or to highlight the desired entry.
Phone Settings The LCD screen displays all entries of the selected list. 3. Press or to highlight the desired entry, and press the View soft key. The LCD screen displays the detail information of the entry. To add an entry to the blacklist from the call history: You can block phone calls from a number by adding this number to the blacklist. For more information on blacklist, refer to Blacklist on page 32. 1. Press the History soft key when the handset is idle.
User Guide W52P IP DECT Phone 1. Press the History soft key when the handset is idle. The LCD screen displays 4 call history lists: All Calls, Outgoing Calls, Missed Calls and Accepted Calls. 2. Press or to highlight the desired list, and press the OK soft key. The LCD screen displays all entries of the selected list. 3. Press 4. Press or to highlight the desired entry. . Network Call Call Log You can access the network call log on the handset.
Phone Settings The LCD screen displays all entries of the selected list. 3. Press 4. Press or to highlight the desired entry. . Dial Plan Dial plan is a string of characters that governs the way your handset processes the inputs received from your handset keypad. The handset supports the following dial plan features: Replace Rule Area Code Block Out The basic expression syntax you need to know: The dot “.” can be used as a placeholder or multiple placeholders for any . character. Example: “12.
User Guide W52P IP DECT Phone Replace Rule You can configure one or more replace rules to remove the specified string and replace it with another string. You can configure a pattern with wildcards (refer to the expression syntax in the table above), so that any string that matches the pattern will be replaced. This feature is convenient for you to dial out a long number.
Phone Settings To configure the area code via web user interface: 1. Click on Phone->Dial Plan->Area Code. 2. Enter the desired values in the Code, Minimum Length (1-15) and Maximum Length (1-15) fields. Note 3. Enter the desired line ID in the Account field or leave it blank. 4. Click Confirm to accept the change. The default values of minimum and maximum length are 1 and 15 respectively. Block Out You can block the dialing of specific numbers.
User Guide W52P IP DECT Phone Outgoing Lines After the handset is registered to the base station, you can assign one or more outgoing lines for the handset. The handset can only use the assigned outgoing line(s) to place calls. When multiple outgoing lines are assigned to the handset, the handset uses the first line as the outgoing line by default. You can change the default outgoing line of the handset. To change the default outgoing line of the handset: 1. Press 2. Select to enter the main menu.
Phone Settings Speed Dial Speed dial allows you to perform single-digit dialing to predefined numbers. This feature is particular useful to users who dial certain numbers on regular basis. A maximum of 8 speed dial numbers are allowed. Assigning a Speed Dial Number You can assign the important numbers of your directory (including local directory, remote phonebook and network directory) to the speed dial keys of your handset.
User Guide W52P IP DECT Phone Placing a Call Using Speed Dial Key To place a call using the speed dial key: 1. Long press the speed dial key (digit key) when the handset is idle. The number assigned to this speed dial key is dialed out. Auto Answer When the auto answer feature is enabled, you can simply answer the incoming calls by lifting the handset from the charger cradle without having to press the off-hook key. The auto answer feature works only if the handset is placed in the charger cradle.
Phone Settings Handset Reset You can reset any individual settings that you have made on the handset. Resetting your handset will not affect the entries of the directory, the call history, the voice mail and the handset’s registration to the base station. But you need to note that other customized settings on the handset will be reset to factory settings after resetting. We recommend that you ask your system administrator for advice before resetting your handset. To reset the handset: 1. Press 2.
User Guide W52P IP DECT Phone To trigger the auto provisioning: 1. Press to enter the main menu. 2. Select 3. Enter the system PIN (default: 0000) and press the Done soft key. 4. Enter the valid value in the Username field and press the OK soft key. 5. Enter the valid value in the Password field and press the OK soft key. ->System Settings->Auto Provision. The LCD screen prompts the warning “Update now?”. 6. Press the Yes soft key to perform an update or press the No soft key to cancel.
Phone Settings If the Eco Mode checkbox is checked, the eco mode is enabled. The color of the signal strength indicator on the idle screen will change to green. Note If the eco mode is enabled, the range of the base station will be reduced.
User Guide W52P IP DECT Phone Call Features The W52P IP DECT phone is designed to be easily used like a regular phone on a public switched telephone network (PSTN). You can place internal and external calls, answer calls, transfer a call to someone else, or conduct a conference call. This chapter provides operating instructions of the call features.
Call Features conversation, you can press the left and right navigation keys to adjust the volume of the currently used audio devices (earpiece, headset or loudspeaker). The call duration displays on the LCD screen while the call is in progress. Placing Internal Calls Calls You can make free internal calls between the handsets registered to the same base station. You can place an internal call to one handset or all handsets registered to the same base station. To place an internal call to one handset: 1.
User Guide W52P IP DECT Phone To place a new call during an active call: You can have at most two calls on your handset. 1. Press the Ext.Call soft key. The active call is placed on hold. 2. Enter the desired number in the Call To field using the keypad. 3. Press or to dial out. You can also make an IP call by directly dialing the IP address of any IP phone. For example, IP: 192.168.1.15.
Call Features Ending Calls To end a call: Do one of the following: - Press - Place the handset in the charger cradle. . Redialing Calls The redial number list stores the twenty last dialed phone numbers. When the memory of the redial number list is full, the handset will automatically erase the oldest dialed number when a new number is dialed. You can redial a call from the redial number list. To redial the last dialed number: 1. Press when the handset is idle. 2. Press again.
User Guide W52P IP DECT Phone To un-mute a call: 1. Press The again. icon disappears from the LCD screen. Call Hold/Resume You can place an active call on hold. At any time, at most one active call can be in progress on your handset. Another call can be answered and made while placing the original call on hold. To place a call on hold: 1. Press the Options soft key during a call, and select Hold. The call is placed on hold and the icon displays on the LCD screen.
Call Features Note 4. Press 5. Press the Save soft key to accept the change or the Back soft key to cancel. or to select the desired value from the Tone field. The call waiting tone works only if the call waiting feature is enabled. To answer a new incoming call during a call: If call waiting feature is enabled, a new incoming call can be answered during a call. 1. Press the Accept soft key to answer the new incoming call. The original call is placed on hold.
User Guide W52P IP DECT Phone To enable the call forward feature for a specific line: 1. Press 2. Select to enter the main menu. ->Call Forward. The LCD screen displays the incoming lines currently assigned to the handset. 3. Press or to highlight the desired line, and press the OK soft key. 4. Press or to highlight the desired forwarding type, and press the OK soft key. or to select Enabled from the Status field. 5. Press 6.
Call Features To perform a semi-attended transfer: 1. Press the Options soft key during a call, and select Transfer. 2. Do one of the following: - Enter the number or select the handset you want to transfer the call to. Press - or the Transfer soft key to dial out. Press the Directory soft key, and select the desired contact. Press the Call soft key. If both the office number and the mobile number of the contact are stored, select the desired number and press 3.
User Guide W52P IP DECT Phone - Press the Directory soft key, and select the desired contact. Press the Call soft key. If both the office number and the mobile number of the contact are stored, select the desired number and press 4. or the OK soft key to dial out. When the second party answers the call, you can consult with him or her before adding to the conference. 5. Press the Conf. soft key again to join all parties in the conference. To join two calls in a conference: 1.
Call Features Anonymous Call Rejection You can use anonymous call rejection feature to reject incoming calls from anonymous callers. Anonymous call rejection automatically rejects incoming calls from callers who deliberately block their identities and numbers from showing up. You can configure the anonymous call rejection feature on a per-line basis. To enable the anonymous call rejection feature for a specific line: 1. Press 2. Select to enter the main menu. ->Anon.Call Rejection.
User Guide W52P IP DECT Phone To configure fast access for voice mail: You can configure fast access to connect straight to the voice mails of the desired line by long pressing the digit key 1, when the handset is idle without having to scroll through the menu. 1. Press 2. Select to enter the main menu. ->Set Key 1. The LCD screen displays the lines assigned to the handset as incoming lines and outgoing lines simultaneously, and the number of voice mails of each line. 3.
Call Features 57
User Guide W52P IP DECT Phone Troubleshooting This chapter provides some general troubleshooting information to help you solve the problems you might encounter when using your W52P IP DECT phone. If you require additional information or assistance with your new phone, contact your system administrator. Why doesn’t the handset ring? Ensure the ringer volume of your handset is not adjusted to the minimum. Refer to Adjusting Ringer Volume on page 17. Make sure the silent mode is not switched on.
Troubleshooting Why can’t I turn the handset on? Ensure the batteries are inserted into the handset. If the batteries are already inserted into the handset, place the handset into the charger cradle. Why do I hear some noise during a call? Ensure you are not using the handset or base station in an area with high electrical interference.
User Guide W52P IP DECT Phone Appendix Firmware Upgrading You can upgrade your base station or handset to the latest firmware version. The latest firmware version not only improves the performance of the base station or handset, but also provides more features compared to the previous versions. Upgrading the Base Station You can upgrade the base station firmware via auto provisioning or via the web user interface.
Appendix firmware file and the firmware upgrading tool (W52P-HS-Flasher.exe), and store them on your local system. To connect the handset to the PC using the USB cable: Before upgrading the handset, you need to connect the handset to the computer. 1. Open the battery cover of the handset. A USB mini port is located underneath the battery cover. 2. Connect the USB cable to the computer. 3. Connect the other end of the USB cable to the USB port on the handset. To upgrade the handset firmware: 1.
User Guide W52P IP DECT Phone Menu Structure System Sta tus Line Sta tus Pla y M essag e Set Voice M a il Set Key 1 Call Forw ard Alw ays Busy No Answ er Do Not Disturb Ca ll Wa iting Anon.
Appendix 63
User Guide W52P IP DECT Phone Regulatory Notices Important Safety Information To reduce risk of fire, severe personal injury and damage to property, read the following safety information carefully before using the product. Environmental Requirements Place the product on a stable, level and non-slip surface. Do not place the product close to heat sources, in direct sunlight or next to any household appliance with strong magnetic field or electromagnetic field, such as a microwave oven or a refrigerator.
Regulatory Notices When there is smoke emitted from the product, or some abnormal noise or smell, disconnect the product from the power supply, and unplug the power adapter immediately. Remove the electrical cord from an outlet by pulling gently on the power adapter, not by pulling the cord. Battery Precautions Do not immerse the battery into water, which could short-circuit and damage the battery.
User Guide W52P IP DECT Phone Index 66
A About This Guide lxxvii Account Registration Adding Contacts 16 30 Adjusting Ringer Volume 17 24 Advisory Tones Always Forward 52 Anonymous Call 55 Anonymous Call Rejection Answering Calls 56 49 61 Appendix Area Code 39 Assigning a Speed Dial Number Attended Transfer Auto Answer 42 53 43 Auto Intercom 43 Auto Provision 44 AC Power 4 B Backlight 24 Base Reset 44 Base Station Description Basic Network Settings Basic Operations 7 14 13 Battery Charging Status Battery Inform
Conference Call 54 Charging the Handset 6 Checking Line Status 17 Checking System Status Copyright 15 lxxii Color Schemes 25 D Date and Time 26 Deleting Contacts 31 Deleting a Speed Dial Number Declaration of Conformity Dial Plan 42 lxxii 38 Displaying Information on LCD Screen Do Not Disturb (DND) 52 E 45 Eco Mode+ Eco Mode 45 31 Editing Contacts Emergency Numbers Ending Calls 40 50 F Firmware Upgrading 61 G Getting Started 1 GNU GPL Information lxxv H Handset Description
Information for DECT Product lxxiv Important Safety Information 65 In This Guide Index lxxvii 67 K Keypad Light 25 L Language 23 Local Directory 28 Locating a Handset 18 Locking/Unlocking Keypad 18 M Main Menu 19 Menu Guidance 19 63 Menu Structure N No Answer Forward 52 25 Notification Light O Overview 7 Outgoing Lines 41 P Packaging Contents Phone Settings 1 22 Placing a Call from Local Directory Placing a Call Using Speed Dial Key Placing Calls 32 43 47 Placing External
Regulatory Notices 65 Remote Phonebook Replace Rule 33 39 Returning to Idle Screen 21 23 Ring Tones S Screen Saver 25 Searching for Contacts 31 Semi-Attended Transfer 53 Setting up the Charger Cradle 5 Setting up the W52P/W52H Handset Shortcuts 27 Signal Strength Speed Dial Submenu 5 10 42 19 Switching Silent Mode On/Off 18 T Table of Contents lxxix Turning Handset On/Off 17 U Upgrading the Base Station 61 Upgrading the Handset via USB Port Using Alphanumeric keys V Voice Mai
WELL W52P IP DECT Phone User Guide Version 1.
Copyright Copyright © 2013 YEALINK NETWORK TECHNOLOGY CO., LTD. Copyright © 2013 Yealink Network Technology CO., LTD. All rights reserved. No parts of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, photocopying, recording, or otherwise, for any purpose, without the express written permission of Yealink Network Technology CO., LTD. Under the law, reproducing includes translating into another language or format.
Part 15 FCC Rules This device is compliant with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Class B Digital Device or Peripheral This equipment is tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RF exposure guidelines. Information for DECT Product This telephone is compliant with the DECT 6.0 standard which operates in the 1.92GHz to 1.93GHz frequency range. Installation of this equipment is subject to notification and coordination with UTAM. Any relocation of this equipment must be coordinated through and approved by UTAM. UTAM may be contacted at 1-800-429-8826.
GNU GPL INFORMATION W52P firmware contains third-party software under the GNU General Public License (GPL). Yealink uses software under the specific terms of the GPL. Please refer to the GPL for the exact terms and conditions of the license. The original GPL license, source code of components licensed under GPL and used in Yealink products can be downloaded from Yealink web site: http://www.yealink.com/GPLOpenSource.aspx?BaseInfoCateId=293&NewsCateId=293&CateId=293. Version 1.
lxxvi
About This Guide About This Guide The WELL W52P IP DECT phone is a full-featured mobile device, which can provide reliable and convenient wireless voice communications. In addition, it provides many widely accepted benefits of the DECT standard, including high security, scalability, and low power consumption to better meet your requirements. This guide provides everything you need to quickly use your new phone.
User Guide W52P IP DECT Phone lxxviii
Table of Contents Table of Contents About This Guide .................................................................. lxxvii In This Guide .......................................................................................................................... lxxvii Table of Contents .................................................................. lxxix Getting Started ............................................................................ 1 Packaging Contents .................................
User Guide W52P IP DECT Phone Phone Settings ........................................................................... 22 Handset Name .........................................................................................................................23 Language ..................................................................................................................................23 Ring Tones .................................................................................................
Table of Contents Answering Calls ........................................................................................................................49 Ending Calls ...............................................................................................................................50 Redialing Calls ..........................................................................................................................50 Call Mute ............................................................
User Guide W52P IP DECT Phone lxxxii
Getting Started Getting Started This chapter provides basic installation instructions and information for obtaining the best performance with the W52P IP DECT phone. The topics include: Packaging Contents Connecting the W52P Base Station Setting up the W52P/W52H Handset Setting up the Charger Cradle Charging the Handset If you require additional information or assistance with your new phone, contact your system administrator.
User Guide W52P IP DECT Phone W52P/W52H Handset Charger Cradle Power Adapter Two Rechargeable Batteries 2
Getting Started Ethernet Cable Belt Clip Quick Installation Guide & Quick Reference Guide CD-ROM Check the list before installation. If you find anything missing, contact your system administrator. Connecting the W52P Base Station You have two options for power and network connection of the base station. Your system administrator will advise you which one to use. AC power Power over Ethernet (PoE) Note Please pay attention to the range of the base station.
User Guide W52P IP DECT Phone AC Power To connect the AC power: 3. Connect the DC plug on the power adapter to the DC5V port on the base station and connect the other end of the power adapter into an electrical power outlet. 4. Connect the supplied Ethernet cable between the Internet port on the base station and the Internet port in your network or the switch/hub device port. Power over Ethernet Using a regular Ethernet cable, the base station can be powered from a PoE (IEEE 802.
Getting Started Setting up the W52P/W52H W52P/W52H Handset To insert batteries into the handset: 4. Open the battery cover. 5. Insert the batteries in the correct polarity. 6. Close the battery cover. Note Do not short-circuit the batteries, as short-circuiting the terminals may damage the batteries or the handset. Do not use damaged batteries, as using damaged batteries may cause an explosion. Battery Information Technology: Nickel Metal Hydride (NiMH) Size: AAA Voltage: 1.
User Guide W52P IP DECT Phone Charging the Handset To charge the handset: 2. After setting up the handset and charger cradle, place the handset in the charger cradle. The original handset included in the W52P package is pre-registered to the base station. After charging, the handset is ready to use.
Overview Overview This chapter provides the overview of the W52P IP DECT phone. The topics include: Base Station Description Handset Description Displaying Information on LCD Screen Icon Instructions If you require additional information or assistance with your new phone, contact your system administrator. Base Station Description After the base station starts up successfully and the handset is registered to the base station, all LEDs on the base station illuminate solid green.
User Guide W52P IP DECT Phone Item Description Indicates the network status. ③ Network Status LED Slow flashes green when the network is unavailable. Illuminates solid green when the network is ready. Indicates the power status of the base station. Slow flashes green when the base station is during the firmware upgrading process. ④ Power Indicator LED Slow flashes green when the base station is during the resetting process. Illuminates solid green when the base station is powered on.
Overview Hardware component instructions of the W52P/W52H handset are: Item ① Earpiece ② LCD Screen ③ Soft Keys Description Outputs audio during the earpiece call. Shows call information, handset status icons, prompt messages and so on. Label automatically to identity their context-sensitive features. Switches between the earpiece and speakerphone ④ Speakerphone Key modes. Answers an incoming call. ⑤ Headset Connector Connects a headset. Answers an incoming call.
User Guide W52P IP DECT Phone Displaying Information on LCD Screen The idle screen may be shown as below: Status Line Text Line Soft Key Line The LCD screen is divided into three parts: status line, text line and soft key line. The information shown in the status line: On hook (idle) — displays signal strength indicator, internal handset number and battery status. Off hook — displays line ID.
Overview Icon Instructions Icons appear on the LCD screen are described in the following table: Icon Description Anonymous Call Anonymous Call Rejection Missed Call Voice Mail Keypad Lock Silent Mode Do Not Disturb Call Forward Call Hold Call Mute Unassigned Outgoing Line Unusable Line Loudspeaker On Headset Mode On 11
User Guide W52P IP DECT Phone 12
Basic Operations Basic Operations This chapter provides you with the basic operating instructions of the W52P IP DECT phone. The topics include: Handset Registration Basic Network Settings Checking System Status Account Registration Checking Line Status Turning Handset On/Off Adjusting Ringer Volume Locking/Unlocking Keypad Locating a Handset Switching Silent Mode On/Off Menu Guidance If you require additional information or assistance with your new phone, contact your system administrator.
User Guide W52P IP DECT Phone The handset plays a warning tone and prompts the message “Handset Subscribed” on the LCD screen, which indicates the registration has finished. After successful registration, the internal handset number and handset name appear on the LCD screen. To de-register a handset: 7. Press to enter the main menu. 8. Select 9. Enter the system PIN (default: 0000). ->Registration->De-reg. Handset. 10. Press the Done soft key.
Basic Operations 11. Press the Done soft key. 12. Press or to select Static from the IP Address Type field. 13. Enter the valid values in the IP Address, Subnet Mask, Default Gateway, Primary DNS and Secondary DNS fields. 14. Press the Save soft key to accept the change. If you are using an xDSL modem, you can connect your base station to the Internet via PPPoE mode. The PPPoE port will perform a PPP negotiation to obtain the IP address.
User Guide W52P IP DECT Phone To check the network status: 5. Press 6. Select to enter the main menu. ->System Status. The LCD screen displays the general information and the More… option. 7. Select More …->Network. The LCD screen displays the network status. 8. Press or to scroll through the list and view the specific information. To check the handset status: 5. Press 6. Select to enter the main menu. ->System Status. The LCD screen displays the general information and the More… option. 7.
Basic Operations Checking Line Status You can register up to 5 lines to one base station. The status of each registered line can be checked using the menu of the handset. To check the line status: 3. Press 4. Select to enter the main menu. ->Line Status. The LCD screen displays all lines registered to the base station with icons for indicating line status. For example, the icon in the bottom of a line indicates that the handset has no privilege to place a call using this line.
User Guide W52P IP DECT Phone Locking/Unlocking Keypad You can lock the handset keypad to prevent keys from being accidentally pressed. To lock the keypad: 2. Long press when the handset is idle until the LCD screen prompts the message “Keypad Locked, Press and hold ‘#’ to unlock!”. The keypad is locked and the icon appears on the idle screen. You can still answer or reject incoming calls as usual. You can also end the answered call by pressing . To unlock the keypad: 2.
Basic Operations To switch the silent mode on: 2. Long press until the LCD screen prompts the message “All Ring Tones Off”. The silent mode is on. The icon appears on the idle screen. To switch the silent mode off: 2. Long press again until the LCD screen prompts the message “All Ring Tones On”. icon disappears from the idle screen. The silent mode is off. The Menu Guidance The handset provides a variety of features that are grouped into menu.
User Guide W52P IP DECT Phone 20
Basic Operations To access a submenu feature: 3. Press 4. Press or to highlight the desired submenu. or the OK soft key to access the next menu level. You can cancel the current operation and return to the previous menu level by pressing or the Back soft key. Returning Returning to Idle Screen To return to the idle screen: 2. Long press to quickly exit the menu and return to the idle screen.
User Guide W52P IP DECT Phone Phone Settings This chapter provides you with some instructions to change the settings of your phone.
Phone Settings Handset Name The handset will be assigned a name by default if successfully registered to the base station. You can personalize the handset name. To rename the handset: 5. Press to enter the main menu. 6. Select 7. Edit the current value in the Rename field. 8. Press the Save soft key to accept the change. ->Handset Name. Language The handset supports displaying text in different languages. The default language of the handset is English.
User Guide W52P IP DECT Phone You can also enter the menu ->Audio->Ring Tones->Volume, press or to decrease/increase the ringer volume. Advisory Tones Tones Advisory tones are acoustic signals of your handset, which inform you of different actions and states. The following advisory tones can be configured independently of each other: Keypad Tone: plays when a user presses any key of the keypad. Confirmation: plays when a user saves settings or places the handset in the charger cradle.
Phone Settings Screen Saver You can enable the screen saver to protect the LCD screen if you do not use your handset for a long time. The screen saver of the handset is designed to protect your LCD screen by filling it with an analog clock. When the screen saver is enabled, an analog clock will be activated and displays on the LCD screen if no user activity is sensed for approximately 10 seconds. To configure the screen saver: 4. Press to enter the main menu. 5. Select 6.
User Guide W52P IP DECT Phone To configure the notification light: 6. Press 7. Select 8. Press to enter the main menu. ->Display->Notification Light. or to select the desired value from the Voice Mail field. If Enabled is selected, the message key LED flashes red when the handset receives a new voice mail. 9. Press or to select the desired value from the Missed Call field. If Enabled is selected, the message key LED flashes red when the handset receives a new missed call. 10.
Phone Settings To configure the time format: 4. Press 5. Select 6. to enter the main menu. ->Display->Time Format. Press or to highlight the desired time format, and press the Change soft key. The radio box of the selected time format is marked. The format of the display time on the LCD screen will be changed accordingly. To configure the date format: 4. Press 5. Select 6. Press to enter the main menu. ->Display->Date Format.
User Guide W52P IP DECT Phone Contact Management This section provides the operating instructions for managing contacts. The topics include: Local Directory Blacklist Remote Phonebook Network Directory Local Directory You can store the frequently used contacts in the handset’s local directory, where names and numbers can be freely added, deleted and edited. This allows you to make calls without having to dial the number manually.
Phone Settings 29
User Guide W52P IP DECT Phone To enter a character: You can press the key which contains your desired character a certain number of times to enter the character. To switch the input method: 2. Press . The current input method is indicated on the top right-hand corner of the LCD screen. For example, “ABC” represents the upper-case input method, “abc” represents the lower-case input method and “123” represents the digital input method. To make a space: 2. Press when the input method is not “123”.
Phone Settings 13. Enter the name of the new entry. 14. Press the Save soft key to accept the change or the Back soft key to cancel. Note When you are adding a contact, both the office number and the mobile number cannot be left blank at the same time. When the contact name is left blank, the handset sets the office number or the mobile number as the contact name.
User Guide W52P IP DECT Phone filtered and display on the LCD screen. To search for contacts in the local directory: 4. Press to enter the main menu. 5. Select 6. Enter a few continuous characters of the desired contact name or number using . the keypad. The contacts whose name or number matches the search will appear on the LCD screen after a timeout or when the Search soft key is pressed. You can dial a contact from the result list.
Phone Settings To delete an entry from the blacklist: 5. Press to enter the main menu. 6. Select 7. Press 8. Press the Options soft key, and select Delete. ->Telephony->Caller Blacklist. or to highlight the desired entry. The selected entry will be deleted successfully. To delete all entries from the blacklist: 5. Press to enter the main menu. 6. Select 7. Press the Options soft key, and select Delete All. ->Telephony->Caller Blacklist. The LCD screen prompts the warning “Delete All?”.
User Guide W52P IP DECT Phone 6. Press 7. Select 8. Press to enter the main menu. . or to highlight the name of your corporate directory, and press the Enter soft key. 9. Select the desired contact from the corporate directory. 10. Do one of the following: - If only one number of the contact is stored in the local directory, press to dial out the number.
Phone Settings The handset connects to load the network directory, and then displays the desired network contact list on the LCD screen. To place a call from the network directory: 5. Press 6. Select 7. Press to enter the main menu. ->Network Dir. or to highlight the desired group, and press the Enter soft key. The LCD screen displays the desired network contact list. 8. Press or to highlight the desired entry. 12.
User Guide W52P IP DECT Phone The LCD screen displays all entries of the selected list. 6. Press or to highlight the desired entry, and press the View soft key. The LCD screen displays the detail information of the entry. To add an entry to the blacklist from the call history: You can block phone calls from a number by adding this number to the blacklist. For more information on blacklist, refer to Blacklist on page 32. 6. Press the History soft key when the handset is idle.
Phone Settings 5. Press the History soft key when the handset is idle. The LCD screen displays 4 call history lists: All Calls, Outgoing Calls, Missed Calls and Accepted Calls. 6. Press or to highlight the desired list, and press the OK soft key. The LCD screen displays all entries of the selected list. 7. Press 8. Press or to highlight the desired entry. . Network Call Call Log You can access the network call log on the handset.
User Guide W52P IP DECT Phone The LCD screen displays all entries of the selected list. 7. Press 8. Press or to highlight the desired entry. . Dial Plan Dial plan is a string of characters that governs the way your handset processes the inputs received from your handset keypad. The handset supports the following dial plan features: Replace Rule Area Code Block Out The basic expression syntax you need to know: The dot “.” can be used as a placeholder or multiple placeholders for any . character.
Phone Settings Replace Rule You can configure one or more replace rules to remove the specified string and replace it with another string. You can configure a pattern with wildcards (refer to the expression syntax in the table above), so that any string that matches the pattern will be replaced. This feature is convenient for you to dial out a long number.
User Guide W52P IP DECT Phone To configure the area code via web user interface: 5. Click on Phone->Dial Plan->Area Code. 6. Enter the desired values in the Code, Minimum Length (1-15) and Maximum Length (1-15) fields. Note 7. Enter the desired line ID in the Account field or leave it blank. 8. Click Confirm to accept the change. The default values of minimum and maximum length are 1 and 15 respectively. Block Out You can block the dialing of specific numbers.
Phone Settings Outgoing Lines Lines After the handset is registered to the base station, you can assign one or more outgoing lines for the handset. The handset can only use the assigned outgoing line(s) to place calls. When multiple outgoing lines are assigned to the handset, the handset uses the first line as the outgoing line by default. You can change the default outgoing line of the handset. To change the default outgoing line of the handset: 4. Press 5. Select to enter the main menu.
User Guide W52P IP DECT Phone Speed Dial Speed dial allows you to perform single-digit dialing to predefined numbers. This feature is particular useful to users who dial certain numbers on regular basis. A maximum of 8 speed dial numbers are allowed. Assigning a Speed Dial Number You can assign the important numbers of your directory (including local directory, remote phonebook and network directory) to the speed dial keys of your handset.
Phone Settings Placing a Call Using Speed Dial Key To place a call using the speed dial key: 2. Long press the speed dial key (digit key) when the handset is idle. The number assigned to this speed dial key is dialed out. Auto Answer When the auto answer feature is enabled, you can simply answer the incoming calls by lifting the handset from the charger cradle without having to press the off-hook key. The auto answer feature works only if the handset is placed in the charger cradle.
User Guide W52P IP DECT Phone Handset Reset You can reset any individual settings that you have made on the handset. Resetting your handset will not affect the entries of the directory, the call history, the voice mail and the handset’s registration to the base station. But you need to note that other customized settings on the handset will be reset to factory settings after resetting. We recommend that you ask your system administrator for advice before resetting your handset. To reset the handset: 4.
Phone Settings To trigger the auto provisioning: 7. Press to enter the main menu. 8. Select 9. Enter the system PIN (default: 0000) and press the Done soft key. ->System Settings->Auto Provision. 10. Enter the valid value in the Username field and press the OK soft key. 11. Enter the valid value in the Password field and press the OK soft key. The LCD screen prompts the warning “Update now?”. 12. Press the Yes soft key to perform an update or press the No soft key to cancel.
User Guide W52P IP DECT Phone If the Eco Mode checkbox is checked, the eco mode is enabled. The color of the signal strength indicator on the idle screen will change to green. Note 46 If the eco mode is enabled, the range of the base station will be reduced.
Call Features Call Features The W52P IP DECT phone is designed to be easily used like a regular phone on a public switched telephone network (PSTN). You can place internal and external calls, answer calls, transfer a call to someone else, or conduct a conference call. This chapter provides operating instructions of the call features.
User Guide W52P IP DECT Phone conversation, you can press the left and right navigation keys to adjust the volume of the currently used audio devices (earpiece, headset or loudspeaker). The call duration displays on the LCD screen while the call is in progress. Placing Internal Calls Calls You can make free internal calls between the handsets registered to the same base station. You can place an internal call to one handset or all handsets registered to the same base station.
Call Features To place a new call during an active call: You can have at most two calls on your handset. 4. Press the Ext.Call soft key. The active call is placed on hold. 5. Enter the desired number in the Call To field using the keypad. 6. Press or to dial out. You can also make an IP call by directly dialing the IP address of any IP phone. For example, IP: 192.168.1.15.
User Guide W52P IP DECT Phone Ending Calls To end a call: Do one of the following: - Press - Place the handset in the charger cradle. . Redialing Calls The redial number list stores the twenty last dialed phone numbers. When the memory of the redial number list is full, the handset will automatically erase the oldest dialed number when a new number is dialed. You can redial a call from the redial number list. To redial the last dialed number: 3. Press when the handset is idle. 4. Press again.
Call Features To un-mute a call: 2. Press The again. icon disappears from the LCD screen. Call Hold/Resume You can place an active call on hold. At any time, at most one active call can be in progress on your handset. Another call can be answered and made while placing the original call on hold. To place a call on hold: 2. Press the Options soft key during a call, and select Hold. The call is placed on hold and the icon displays on the LCD screen.
User Guide W52P IP DECT Phone 9. Press or to select the desired value from the Tone field. 10. Press the Save soft key to accept the change or the Back soft key to cancel. Note The call waiting tone works only if the call waiting feature is enabled. To answer a new incoming call during a call: If call waiting feature is enabled, a new incoming call can be answered during a call. 2. Press the Accept soft key to answer the new incoming call. The original call is placed on hold.
Call Features To enable the call forward feature for a specific line: 9. Press to enter the main menu. 10. Select ->Call Forward. The LCD screen displays the incoming lines currently assigned to the handset. 11. Press or to highlight the desired line, and press the OK soft key. 12. Press or to highlight the desired forwarding type, and press the OK soft key. 13. Press or to select Enabled from the Status field. 14.
User Guide W52P IP DECT Phone To perform a semi-attended transfer: 4. Press the Options soft key during a call, and select Transfer. 5. Do one of the following: - Enter the number or select the handset you want to transfer the call to. Press - or the Transfer soft key to dial out. Press the Directory soft key, and select the desired contact. Press the Call soft key. If both the office number and the mobile number of the contact are stored, select the desired number and press 6.
Call Features - Press the Directory soft key, and select the desired contact. Press the Call soft key. If both the office number and the mobile number of the contact are stored, select the desired number and press 9. or the OK soft key to dial out. When the second party answers the call, you can consult with him or her before adding to the conference. 10. Press the Conf. soft key again to join all parties in the conference. To join two calls in a conference: 4. Place two calls on the handset. 5.
User Guide W52P IP DECT Phone Anonymous Call Rejection You can use anonymous call rejection feature to reject incoming calls from anonymous callers. Anonymous call rejection automatically rejects incoming calls from callers who deliberately block their identities and numbers from showing up. You can configure the anonymous call rejection feature on a per-line basis. To enable the anonymous call rejection feature for a specific line: 6. Press 7. Select to enter the main menu. ->Anon.Call Rejection.
Call Features To configure fast access for voice mail: You can configure fast access to connect straight to the voice mails of the desired line by long pressing the digit key 1, when the handset is idle without having to scroll through the menu. 4. Press 5. Select to enter the main menu. ->Set Key 1. The LCD screen displays the lines assigned to the handset as incoming lines and outgoing lines simultaneously, and the number of voice mails of each line. 6.
User Guide W52P IP DECT Phone 58
Troubleshooting Troubleshooting This chapter provides some general troubleshooting information to help you solve the problems you might encounter when using your W52P IP DECT phone. If you require additional information or assistance with your new phone, contact your system administrator. Why doesn’t the handset ring? Ensure the ringer volume of your handset is not adjusted to the minimum. Refer to Adjusting Ringer Volume on page 17. Make sure the silent mode is not switched on.
User Guide W52P IP DECT Phone Why can’t I turn the handset on? Ensure the batteries are inserted into the handset. If the batteries are already inserted into the handset, place the handset into the charger cradle. Why do I hear some noise during a call? Ensure you are not using the handset or base station in an area with high electrical interference.
Appendix Appendix Firmware Upgrading You can upgrade your base station or handset to the latest firmware version. The latest firmware version not only improves the performance of the base station or handset, but also provides more features compared to the previous versions. Upgrading the Base Station You can upgrade the base station firmware via auto provisioning or via the web user interface. This section provides you with the instruction of upgrading the base station via the web user interface.
User Guide W52P IP DECT Phone To upgrade the handset firmware, contact your system administrator for the latest firmware file and the firmware upgrading tool (W52P-HS-Flasher.exe), and store them on your local system. To connect the handset to the PC using the USB cable: Before upgrading the handset, you need to connect the handset to the computer. 4. Open the battery cover of the handset. A USB mini port is located underneath the battery cover. 5. Connect the USB cable to the computer. 6.
Appendix Menu Structure System Sta tus Line Sta tus Pla y M essag e Set Voice M a il Set Key 1 Call Forw ard Alw ays Busy No Answ er Do Not Disturb Ca ll Wa iting Anon.
User Guide W52P IP DECT Phone 64
Regulatory Notices Regulatory Notices Important Safety Information To reduce risk of fire, severe personal injury and damage to property, read the following safety information carefully before using the product. Environmental Requirements Place the product on a stable, level and non-slip surface. Do not place the product close to heat sources, in direct sunlight or next to any household appliance with strong magnetic field or electromagnetic field, such as a microwave oven or a refrigerator.
User Guide W52P IP DECT Phone When there is smoke emitted from the product, or some abnormal noise or smell, disconnect the product from the power supply, and unplug the power adapter immediately. Remove the electrical cord from an outlet by pulling gently on the power adapter, not by pulling the cord. Battery Precautions Do not immerse the battery into water, which could short-circuit and damage the battery.
Index Index A D About This Guide lxxvii Account Registration 16 30 Adding Contacts Adjusting Ringer Volume 17 Advisory Tones 24 Always Forward 52 Anonymous Call 55 Anonymous Call Rejection 56 Answering Calls 49 Appendix 61 Area Code 39 Assigning a Speed Dial Number 53 Attended Transfer Auto Answer 43 Auto Intercom 43 Auto Provision 44 AC Power 4 Date and Time 26 Deleting Contacts 31 42 Deleting a Speed Dial Number Declaration of Conformity lxxii Dial Plan 38 Displaying Information on LCD Screen Do Not
User Guide W52P IP DECT Phone WEEE Warning M Main Menu 19 Menu Guidance 19 Menu Structure 63 N No Answer Forward 52 Notification Light 25 O 7 Overview Outgoing Lines 41 P Packaging Contents 1 Phone Settings 22 Placing a Call from Local Directory Placing a Call Using Speed Dial Key Placing Calls 47 Placing External Calls 48 Placing Internal Calls 48 Power over Ethernet 4 32 43 R Redialing Calls 50 Regulatory Notices 65 Remote Phonebook 33 Replace Rule 39 21 Returning to Idle Screen Ring Tones 23 S Scre