8820IP Phone User Manual_ SIP (V1.
8820IP Phone User Manual_ SIP (V1.44) 8820IP Phone User Manual_ SIP(V1.44) 8820IP PHONE USER MANUAL_ SIP(V1.44) ................................ 1 Ø Appearance:.......................................................................................................................4 Ø Features ...........................................................................................................................5 Ø Standard and Protocol..................................................................
8820IP Phone User Manual_ SIP (V1.44) PA168X SIP PHONE TELNET SETUP GUIDE............................. 35 Ø Telnet Configuration ......................................................................................................35 Ø PA168X Telnet Commands Explanation......................................................................36 Ø Command ?....................................................................................................................36 Ø Command get..................
8820IP Phone User Manual_ SIP (V1.44) Ø Appearance: ● PA168X SIP Phone Front Illustration (Refer to Fig 1.1): Fig 1.1 PA168X Phone Front Illustration ● PA168X SIP Phone Back Illustrations(Refer to Fig 1.
8820IP Phone User Manual_ SIP (V1.44) Power Jack To network To PC Fig 1.2 PA168X SIP Phone Back Illustration Ø Features Ø Hardware ● Main chip—PA1688 50MHz ● Data Memory—2MB SDRAM ● Program Memory—2 MB Flash memory ● Ethernet Port—2X 10/100M Connectors ● AC/DC adapter—Input AC100--- 230V，Output 9V DC, 1A Ø Software ● DHCP support for LAN or Cable modem ● PPPoE support for ADSL or Cable modem ● Set phone by HTTP web browser or Telnet ● Upgrade by FTP(TFTP optional) ● Support major G.
8820IP Phone User Manual_ SIP (V1.44) ● CNG (Comfort noise generation) ● Dynamic voice jitter buffer ● G.167/165 compliant 16ms echo cancellation ● Tone generation and Local DTMF re-generation according with ITU-T ● Support the Inband audio; RFC2833; SIP INFO etc DTMF transmission method ● E.
8820IP Phone User Manual_ SIP (V1.
820IP Phone User Manual_ SIP (V1.44) Ø Installation: 1． Connect handset to base: insert handset cord into handset cord jack at the left side of the base. 2． Connect IP phone to Internet: plug the RJ-45 Ethernet cable into the Ethernet Jack. Plug the other end of the cable into HUB or switch. 3． Power on IP phone: plug the power cord adapter into the Power Jack. Then plug the other end of the power cord adapter into the appropriate wall outlet.
8820IP Phone User Manual_ SIP (V1.44) Ø Suitable Uses of 8820IP phone 8820IP Phone is the ideal choice for those who always place international or long distance calls. If two parties both use 8820 serial IP Phone, they can communicate with each other even free.
8820IP Phone User Manual_ SIP (V1.44) Mis CALL With handset hung, press this key to review missed Calls VOLUME+ Increase the volumes of handset or speaker; turn over the record backward VOLUME- Decrease the volumes of handset or speaker; turn over the record forward 8820 IP Phone Front Illustration (Refer to Fig 1.0): When 8820IP phone has been installed properly, you can enter the menu through the keyboard and LCD, and then set each parameter accordingly.
8820IP Phone User Manual_ SIP (V1.44) Vol＋ Keypads Turn over menu backward Modify values Vol REDIAL Turn over menu forward; move cursor backward; Delete input Exit current menu; exit setting mode Ø Operate with the keys ● Enter the menu mode Press “H.F” key, and then use the keyboard to enter the password of the phone (when debug is not set as 0[disable], default password is 1234; when debug is set as 0[disable], please use super password 12345678), Secondly, Press “H.
8820IP Phone User Manual_ SIP (V1.44) If the errors come forth when you enter the settings, press “VOL-” key to delete it and enter the settings again ● Abort the settings If there is no need for the modified settings, press “Redial” key to return to the main menu, and press “VOL+” or “VOL-” to page the menu up or page the menu down; When “exit settings” submenu item is selected, press “H.F” key to confirm, 8820IP phone will reboot and be used the current settings.
8820IP Phone User Manual_ SIP (V1.44) Fig 1.1 Main Menu structure Illustration Ø Set the network submenu ● Network Submenu Structure Fig 1.
8820IP Phone User Manual_ SIP (V1.44) Fig 1.3 Audio submenu structure Illustration Ø Set the dial plan submenu ● Dial plan submenu Structure Fig 1.
8820IP Phone User Manual_ SIP (V1.44) Fig 1.5 Protocol submenu structure Illustration Ø Set the other menu ● Other Submenu Structure Fig 1.6 other submenu structure Illustration Ø Set the Advanced menu ● Advanced Submenu Structure Fig 1.
8820IP Phone User Manual_ SIP (V1.44) Keys Press Once Press Twice Press Thrice Press quartic Press quintic 1 1 . , ?/_ !// 2 2 A/a B/b C/c [ 3 3 D/d E/e F/f ] 4 4 G/g H/h I/i * 5 5 J/j K/k L/l 6 6 M/m N/n O/o # 7 7 P/p Q/q R/r S/s 8 8 T/t U/u V/v 9 9 W/w X/x Y/y * 0 # Z/z .
8820IP Phone User Manual_ SIP (V1.44) PA168X SIP Phone Http Setup Guide When PA168X SIP phone is properly installed, you can set each parameters through PC and Web browser. Details please refter to 《Pa168X SIP phone Spec and Install》 Ø Configured by WEB Double click icon to open the IE browser. Input the IP address of the phone into address bar ( ), and then input password of the phone into the following page.
8820IP Phone User Manual_ SIP (V1.44) Fig 1.1 Http Setting Default password 1234 is ordinary password and super password is 12345678. With Debug set 0[disable], please input super password; while Debug is not set as 0[disable], please input ordinary password. Then click button. The following configured page wills popup.
8820IP Phone User Manual_ SIP (V1.44) Fig 1.2 Network Setting ● iptype: Set how IP phone gets relevant network parameters by selecting corresponding item from drop down list. n static ip: Select this item to authorize users set IP address, subnet mask and router IP address of IP phone manually. n dhcp: Select this item to enable DHCP mode. With this system, your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on.
8820IP Phone User Manual_ SIP (V1.44) ● ppp id: With pppoe or modem selected in iptype drop down list, please enter the user name here. ● ppp pin: With pppoe or modem selected in iptype drop down list, please enter the password here. ● local ip: With static ip selected in iptype drop down list, please enter IP address of IP phone here. ● subnet mask: With static ip selected in iptype drop down list, please enter subnet mask of IP phone here.
8820IP Phone User Manual_ SIP (V1.44) Ø Audio settings: Fig 1.3 Audio Setting ● codec1: Set the priority 1 of the audio compression algorithm. The options are g729，g7231，g711u，g711a , gsm, ilbc and null. ● codec2: Set the priority 2 of the audio compression algorithm. The options are g729，g7231，g711u，g711a , gsm, ilbc and null. ● codec3: Set the priority 3 of the audio compression algorithm. The options are g729，g7231，g711u，g711a , gsm, ilbc and null.
8820IP Phone User Manual_ SIP (V1.44) ● agc: Enable/disable AGC. ● aec: Enable/disable VEC. ● audio frame: Set audio frames in RTP package. Minimum is 1 and maximum is 8. ● g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate is 6.3kbps, low rate is 5.3kbps. ● ilbc payload : Set the payload type of RTP package whne ILBC codec selected to DTMF delay. The value range is 96-255. ● jitter size : Set buffer size of RTP package. The value range is 0-32.
8820IP Phone User Manual_ SIP (V1.44) n Advanced: Set ring used the individualized tone provided by system (need system support). ● speaker out: Set the volume of handfree output. ● speaker in: Set the volume of handfree input. Ø Dial Plan settings: Fig 1.4 Dial Plan Setting ● use dialplan: Set whether use dial plan or use dial number by selecting the corresponding item in drop down list. n disable: Do not use dial plan or dial number by selecting this item.
8820IP Phone User Manual_ SIP (V1.44) please enter the dial prefix into this field according to requirement of log in server. ● ddd code: With enable or dialnum selected in use dialplan drop down list, set area code according to E.164 dial rule. For example, Beijing is 10; Shanghai is 21. ● idd code: With enable or dialnum selected in use dialplan drop down list, set country code according to E.164 dial rule. For example, China is 86; U.S.A is 1.
8820IP Phone User Manual_ SIP (V1.44) ● Call waiting: Enable/disable call waiting by checking/unchecking the box. ● forward number: Enter receiving forwarded calls phone number into this field; If the IP phone used with modem, with modem item selected in iptype list box, and then fill ISP number into this field. ● fwd noanswer: Forward calls without replying by checking this box. Please enter receiving forwarded calls phone number into fwd number field.
8820IP Phone User Manual_ SIP (V1.44) ● use service: Enable/disable service by checking/clearing this box. To make calls through SIP Proxy Server, please check this box; otherwise, phone can only make IP-to IP calls. ● register ttl : IP phone will send a keep-alive registration message to SIP proxy server every “register ttl” seconds. The minimum value is 10, maximum value is 65535. Default is 60. ● service type: This option is used to accommodate the miscellaneous requirements of the system providers.
8820IP Phone User Manual_ SIP (V1.44) § stanaphone: Use Stanaphone’s SIP system § net2phone: Use Net2phone’s SIP system § Fwd: Free SIP service; please visit www.freeworldialup.com for more information. § Inphonex: Free SIP service; please visit www.inphonex.com for more information. § sipphone: Free SIP service ; please visit www.sipphone.com for more information.
8820IP Phone User Manual_ SIP (V1.44) please select an item from dropdown list. n disable: Select this item when the sip proxy server and IP phone in the same LAN, or the sip proxy system supports the IP phone working behind the LAN. n enable: When the system does not support IP phone working behind the LAN, please select this item to search public IP address of the NAT device. With this item selected, “nat addr” field will be activated.
8820IP Phone User Manual_ SIP (V1.44) device alive. “nat ttl” is an integer between 10 and 65535, default value is 20. ● phone number: The local phone number or username of this phone, usually is allocated by system. ● account: With SIP system which requires authentication, please put the username/account into this field. ● pin: With SIP system which requires authentication, please put the password into this field.
8820IP Phone User Manual_ SIP (V1.44) ● dtmf: Set DTMF signal sending way by selecting inband audio, rfc 2833 and sip info from list box. ● dtmf payload : When DTMF select rfc 2833.This parameter can be used indicating type of RTP payload type. The value can be use integer 96-101. ● prack: Enable/disable support pre-ack(RFC3262) by checking/clearing this box. ● super password: Set the super password of the phone.(Default super password is 12345678). ● debug: Set the debug level of the phone.
8820IP Phone User Manual_ SIP (V1.44) Ø Other settings: Fig 1.6 Other Setting Page ● password: Set the password of the phone. (Default password is 1234). ● upgradetype: Set the auto-upgrade type of the phone. n disable : Disable auto-upgrade . n all: pa168X phone will find matching firmware binary file and configuration file of the hardware type only at the FTP server specify by upgradeaddr item .
8820IP Phone User Manual_ SIP (V1.44) and configuration file of the phone only at the FTP server specify by upgradeaddr item . ● upgrade addr: Put IP address or domain name obtained by ISP of FTP server supplying upgrade program into this field. ● sntp ip: Fill IP address of time server here. When network without Internet connect, Fill special IP address 255.255.255.255. ● use daylight: Enable/disable daylight. ● timezone: Select correct time zone in list box.
8820IP Phone User Manual_ SIP (V1.44) Fig 1.7 Setting Page using ordinary pin with Debug set as 0 [disable] ● Save Settings : Click this button to save the configuration and the phone will reboot. Once the phone reboots successfully, the new configuration is effective. Note After entering set page, if save settings button is not clicked within 10 minutes, then when you click it again, the index page asking for pin will pop up again.
8820IP Phone User Manual_ SIP (V1.44) Name field following 001, and then input 5989426454 into Phone number field. Then Jack’s number 5989426454 is saved in phone book. Then please click Save/Back button. In normal state, you can use speed dial to call numbers saved in phone book. Fig 1.8 Phone Book Illustration ● Upgrade Firmware: Click this button to update the program ,the settings and the digitmap of IP phone.
8820IP Phone User Manual_ SIP (V1.44) PA168X SIP Phone Telnet Setup Guide When PA168X SIP phone is properly installed, you can set each parameters through PC and Telnet commands. Details please refter to 《PA168X SIP phone Spec and Install》 Ø Telnet Configuration ● On the PC choose Start>Run, and then type telnet 192.168.1.100 into Run field in popuping Run dialog. Or input telnet 192.168.1.100 in the DOS window. Then the following information will be displayed. PA168X V1.
8820IP Phone User Manual_ SIP (V1.
8820IP Phone User Manual_ SIP (V1.44) P:\>? set get store x load x exit write list settings store current to xth settings load xth settings to current save settings Ø Command get Syntax description: No optional parameter of keywords Usage: Display basic parameters of the PA168X IP phone Relevant usage: None Detailed description: get Display basic running parameters of the PA168X IP phone.
8820IP Phone User Manual_ SIP (V1.44) dialplan 1[enable] dddcode 10 iddcode 86 iddprefix 00 dddprefix 0 innerline 1[enable] innerlineprefix 0 callwaiting 1[disable] fwdnumber 82378009 fwdpoweroff 1[enable] fwdalways 1[enable] fwdbusy 1[enable] fwdnoanswer 1[enable] answer 30 digitmap 1[enable] ***************Protocol Settings*************** service 1[enable] registerttl 60 servicetype 0[common] sipproxy 203.93.9.57 domain/realm 203.93.9.
8820IP Phone User Manual_ SIP (V1.44) dialplan 1[enable] dddcode 10 iddcode 86 iddprefix 00 dddprefix 0 innerline 1[enable] innerlineprefix 0 callwaiting 1[disable] fwdnumber 82378009 fwdpoweroff 1[enable] fwdalways 1[enable] fwdbusy 1[enable] fwdnoanswer 1[enable] answer 30 digitmap 1[enable] ***************Other Settings*************** password 1234 upgradetype 0[disable] upgradeaddr [empty] sntpip 0.0.0.
8820IP Phone User Manual_ SIP (V1.44) or router and powered up; 2: use PPPoE mode. Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them. With this system, ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on; 3: use modem mode. Those who use IP phone with modem, please set the value as 3.
8820IP Phone User Manual_ SIP (V1.44) With iptype set as 0, use this command to set IP address of DNS server. set dns2 XXX.XXX.XXX.XXX With iptype set as 0, use this command to set IP of backup DNS server. set mac XX-XX-XX-XX-XX-XX Set MAC address of the PA168X IP phone. Parameter xx-xx-xx-xx-xx-xx must be an HEX number. set codec1 X Set the priority 1of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5: ilbc; 6: null.
8820IP Phone User Manual_ SIP (V1.44) Set the priority 4 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5: ilbc; 6: null. set codec5 X Set the priority 5 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5: ilbc; 6: null. set codec6 X Set the priority 6 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5: ilbc; 6: null.
8820IP Phone User Manual_ SIP (V1.44) 0 and 7. set 6.3k X With G.7231, set PA168X IP phone to use 6.3K rate or not. X is ranged from 0 through 1: 0: use 6.3K rate; 1: use 5.3K rate. set jittersize X Set buffer size of RTP package. X is range from 0-32. set ilbcpayload X Set the payload type of RTP package whne ILBC codec selected to DTMF delay.X is range from 96-255. set handsetin X Set initial volume of handset. X is ranged from 0 through 15. set handsetout X Set initial volume of handout.
8820IP Phone User Manual_ SIP (V1.44) Set initial volume of speaker out. X is ranged from 0 through 31. set dialplan X Enable/disable dial plan and dial number. Parameter X ranged from 0 through 4: 0: disable dial plan; 1: enable dial plan; 2: use dial number; 3: use 179XX service.;4: use hotline function. set dialnumber XX When set dialplan value set as 2, please use this command to set dial number. For example, with eTalk card used, please set it as 00.
8820IP Phone User Manual_ SIP (V1.44) Set IDD service prefix number when set dialplan value set as 1 or 2. For example, IDD service prefix number of china is 00; IDD service prefix number of USA is 1, etc. Parameter xxx must be an Arabic numeral and no longer than 3 characters. set dddprefix XX Set DDD service prefix number when set dialplan value set as 1 or 2. For example, DDD service prefix number of china is 0; DDD service prefix number of USA is 1, etc.
8820IP Phone User Manual_ SIP (V1.44) set fwdalways X Enable/disable forward all calls. X is ranged from 0 through 1. 0: do not forward all calls; 1: forward all calls. set fwdbusy X Enable/disable forward calls if busy. X is ranged from 0 through 1. 0: do not forward calls if busy; 1: forward call if busy. set fwdnoanswer X Enable/disable forward calls without replying. X is ranged from 0 through 1. 0: do not forward calls without replying; 1: forward call without replying.
8820IP Phone User Manual_ SIP (V1.44) value is 60 Sec. set service type X Enable/disable the prepaid and service system .choose the repaid server provider.
8820IP Phone User Manual_ SIP (V1.44) set sipproxy XXXX Set IP address or domain name of SIP Proxy Server. set domain/realm XXXXX Set the domain name of SIP proxy server. set nattraversal X X ranged from 0 through 2: 0: do not use NAT traversal. When the log in server and IP phone in the same LAN, or the log in system supports the IP phone working behind the LAN; 1: Use NAT traversal.
8820IP Phone User Manual_ SIP (V1.44) www.whatismyipaddress.net;checkip.dyndns.org set natttl XX Set NAT TTL XX is an integer between 10 and 65535 sec. default value is 20 sec. set phonenumber XXXXXXXX Set a local ID of PA168X IP phone. Value xxxxx must be an Arabic numeral and no longer than 16 characters. set account XXXXXX Set the account; Value xxxxxx must be an Arabic numeral and no longer than 32 characters.
8820IP Phone User Manual_ SIP (V1.44) Set DTMF relay type. X is ranged form 0 through 2: 0: inband audio；1: rfc 2833；2: sip info. set dtmf payload X When dtmf X select 1(rfc 2833).This parameter can be used indicating type of RTP payload type. The value can be use integer 96-101. set prack X Set enable/disable support pre-ack(RFC3262) . X is ranged form 0 through 1: 0: disable；1: enable. set outboudproxy X Set enable/disable Outbound proxy support. X is ranged form 0 through 1: 0: disable；1: enable.
8820IP Phone User Manual_ SIP (V1.44) Set open debugging message output grade for special tool. X is ranged from 0 through 5: 0: close debugging output; 1: output the operation information to the window; 2: output all the bug information and data in test window; 3: save the bug information into SDRAM; 4: disable checks the mark. set password XXXX Set password of the PA168X IP phone. XXX must be ASCII characters.
8820IP Phone User Manual_ SIP (V1.44) set timezone XX Set time zone. Ø Command store Syntax description: no keyword. Parameter ranged from 0 through 4. Usage: Save the current settings to the designated position. Relevant Usage: store 1 Ø Command load Syntax description: no keyword. Parameter ranged from 0 through 4. Usage: Load the designated settings to the current position.
8820IP Phone User Manual_ SIP (V1.44) Ø Command ping Syntax description: ping IP address Usage: ping IP address of other NAT device Relevant usage: In telnet window, input ping xx.xxx.xx.xx（an IP address） and return, then the result will be displayed. If the address is effective, “ping OK” will be seen; if the address is ineffective, nothing will be seen. Fox example: P:\>ping 203.93.9.57 P:\> ping OK P:\>ping 27.56.120.56 P:\> Note Usually, the echo time of ping command is no more than 1 second.
8820IP Phone User Manual_ SIP (V1.44) PalmTool. This operation aims at testing. X-1: Connect to FTP Server to get the file of updating program and update program Flash. This operation aims at updating program. X-2: Connect to FTP Server to get the file of updating dial rules and update program Flash. This operation aims at updating dial rule.
