GSM LCD Alarm System WL1014 User Manual Date Issued: 2011-01-08
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Thank you for purchasing this alarm system. For proper use and your safety, please read these instructions thoroughly and carefully before you put the system in use. Keep this manual carefully for your reference in the future. Warning Do not remove the front or back cover of the unit and keep it intact. There is no part that can be repaired by user. If repair is needed, please send it to seller or authorized service point.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Read this manual carefully before you Proper use put he system in use. Operate in accordance with the instructions herein. Water-proofness Qualified maintenance service The alarm system is not waterproof. Please keep it dry. Only those qualified maintenance professionals may repair the alarm system. Be sure to back up all important Backup information stored in the system.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Addition of other equipment Switch on safety Interference Before adding other equipment, please read the user manual for detailed safety instructions. Be sure not to connect incompatible products to the system. Do not switch the Device on when wireless phone use is prohibited or when it may cause interference or danger. All wireless devices may be susceptible to interference, which could affect performance.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Table of contents 1. 2. 3. 4. 5. 6. 7. Brief introduction ----------------------------------------------------6 Standard Packing list ----------------------------------------------6 Function Introduction ----------------------------------------------6 Alarm Host Diagram -----------------------------------------------7 Installation ------------------------------------------------------------9 5.
Well SEC Electronic Co., Ltd 8. 9. 10. 11. 12. 13. 14. Http://www.wellsecurityalarm.com 7.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 1. Brief introduction The WL1014 is an innovative safety solution for home, office and industry. It integrates GSM network, SMS Control, voice, wireless communication and proprietary technologies. It is suitable for a wide range of applications. 2.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Alarm Panel back schematic diagram: Wired terminal block: LCD display: Page ８ of 35 Ver 2.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 5. Installation 5.1 Insert SIM into Control Unit Please see the below photos: Please insert SIM card and plug in power adaptor, and then power on the system, all the LED lights will be on for 2 seconds and you will hear a long Page ９ of 35 Ver 2.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com beep; the system comes into initialization. After the time clock displays on the LCD screen, the [SGM] starts flashing and the main unit starts to detect the GSM network until a long beep. Then the [SGM] indicator goes out indicating the system comes into disarm status. Finally, turn on the backup battery switch. 5.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Installation: attach the larger half to the floor and attach (rivet or glue) the smaller half to the scroll steel door. An alarm is triggered when the halves are separated by more than three to 5.00 cm. Scroll Steel Door 5.3 Install the wireless PIR Motion Sensor The PIR sensor will detect a person since human temperature is different to ambient temperature. When triggered, the PIR will signal the Control Unit.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 5.4 Install other sensors For smoke, you can use wireless smoke sensor, for gas leakage detection, you can install gas leakage sensor below For temperature, you can install the temperature sensor below: 5.5 Install the Control Unit In order to avoid destruction of the Control Unit by intruders, please install it in a concealed location, convenient to the operator.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 2) Wired strobe siren 3) wireless outdoor siren Wiring Diagram of Outdoor siren for WL1014 6. Settings 6.1 Enter Settings In the state of disarm, input 4-digit password by the keypad on the main unit and press [#] button to confirm. You will hear a voice prompt: please enter instruction. At the same time, [SET] indicator is on without flashing and [0000] displays on the screen, indicating the system enters setting status.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 6.2 Exit Settings Press [*] and [#] buttons, the main unit emits a long beep and exits settings. The [SET] indicator goes out and the system returns to disarm state. Operating method: 【*】➩【#】 6.3 Factory Reset In disarm status, use keypad to input [95175308246] and press [#] to confirm, all the LED indicators will be on for 2 seconds and you will hear a long beep.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com remote controllers. LCD display: 4 6.4.2 Delete Remote Controller The remote controller can’t control the main unit after it’s deleted. In setup state, use keypad to input [21], then input the remote controller number [1-8], and then press [#] to confirm. The main unit emits a long beep and the [Signal] indicator flickers once. You will hear a voice prompt “delete completed”.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 6.5.2 Delete Defense Zone The wireless detector can’t control the main unit after it’s deleted. In setup state, use keypad to input [24], then input the defense zone number you want to delete [01~99], and then input [#] to confirm. The main unit emits a long beep and the defense zone indicator flickers once. You will hear a voice prompt “delete completed”. Operating method: [24]➩[XX]➩[#] XX indicates: 01 ~99 defense zones number 6.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com In setup status, use keypad to input [31], then input the 4-digit new password, and then press [#] to confirm. The main unit will make a long beep and you will hear a voice prompt “setting completed”.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 6.8 Timing Settings 6.8.1 Timely Arm In setup status, use keypad to input [33~35], then input the hour [AA] and minute [BB] of the time you want to set to arm, and finally input [#] to confirm. You will hear a long beep and a voice prompt “setting completed”.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 6.8.3 Timing Control In setup status, use keypad to input [39], then input the number indicating turning on timely arm/ disarm [1/0], and then input [#] to confirm. You will hear a long beep and a voice prompt “setting completed”. The factory default is off.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 6.9.2 Delete alert target phone number In setup state, input [51] ~ [56], and then press [#] to confirm, the main unit will make a long beep and the [Signal] indicator will flicker once and you will hear “delete completed”, which indicate the alarming user number is deleted successfully. Operating method: [XX]➩[#] XX indicates: the 1- 6 alarming user number [51] ~ [56] For example: Delete the third alarming user number from the system.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Operating method: [57]➩[138222222]➩[#] 6.10.1 Delete SMS Alert Target cell phone number In setup state, use keypad to input [57] ~ [59], and then press [#] button to confirm. The main unit will make a beep, the [Signal] indicator will flicker once and you will hear “delete completed”, which indicate SMS number is deleted successfully.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com For example: set defense zone 12 to be 24-hour, fire alarm and siren on Operating method: [60]➩[12]➩[3]➩[2]➩[1]➩[#] 6.12 Home Arm Defense Zone Setting If you want some detectors work and some do not, you can use [Home Arm] function. In setup state, use keypad to input [61], then choose the corresponding defense zone number [01~99], then choose [Home Arm], and then choose whether alarm [0/1] button, and finally press [#] to confirm.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 6.14 Siren Setting In setup state, use keypad to input [75]; in the operation of arm/ disarm by remote control, select if the siren sounds or not by [0/1] button, and then press [#] to confirm. The main unit will emit a long beep and a voice prompt “setting completed”.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com System status. There are 4 status as following: 1) Arm: defense zone 1~99 will alarm when detectors are triggered 2) Home Arm: in arm status, the defense zone which is set as [Home Arm] will alarm when detectors are triggered. 3) Disarm: defense zone 1~99 will not alarm when detector triggered (except 24 hours defense zone) 4) System setup status: In this status, all defense zones will not alarm when detectors are triggered. 7.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 7.1.2 Disarm It means to stop the alarm when the main unit sounds the alarm or make the alarm system in the state of non-warning. After disarming, even if you trigger the detector, the main unit would not sound alarm (excluding 24-hour defense areas). Use keypad to input system password, then press [#] button. [Out Home] or [At Home] lights will be off. It means disarm setting successful.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 7.1.4 Emergency Help Press [Emergency ] button on keypad, or [ ] button on remote controller or wireless panic button, the main unit will alarm and make call to the preset user numbers. 7.2 Answer Alarm Call When the main unit sounds alarm, it will dial the preset numbers. If no one answers the call, the system will call the next user number automatically. The system will call each preset numbers for 3 times in order.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Press [2]: disarm, if finished successfully, you will hear a voice prompt “System disarmed”. Press [3]: monitoring for 30 seconds, to continue monitoring, press [3] again to monitor for another 30 seconds. Press [4]: two-way intercom for 30 seconds. You can’t operate the main unit during this time. 7.4 System Dialing Function In disarm status, you can use the main unit to make any call just like a land-line telephone.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com GSM Signal Checking Before installing the main unit, you should check the signal of the installing place in order to ensure the unit can perform well. In setup state, input [81] ➩#, the main unit will make a long beep and display 00+XX (XX indicates the intensity of the signal). And the intensity should be within the range of 07-31; if it’s less than 07, you should change place.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com GSM Frequency 900/ 1800/ 1900MHz Back-up Battery NI-HI AAA*6 DC7.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 9. Care The alarm system has excellent design and uses advanced technologies. It shall be used with care. The following suggestions are required to maintain your obligations under the warranty terms, and for prolonging the service life of the system. 1) Place the control panel and all parts and accessories out of children’s reach. 2) Keep the alarm system dry.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 2) Make sure the PIN code verification of the SIM card is closed. 3) Please keep the password and SIM card number safe, in case that other people remote control the system illegally. a. Since the alarm system is continuously in operation or standby mode, the supply adaptor of the control panel shall be connected to a safe and reliable socket. b.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 5) Connect L and N is means 0, and connect H and N is means 1, connect neither L and N nor H and N is means 2 ; 6) According to below table, select the Zone and set the 3X4 PIN Wireless data bits code area according to selected zone. 7) Make sure the jumpers are correct. Then install the cover carefully. 8) Turn off the sensors’ power before setting . 9) Trigger the wireless sensor and test the setting result.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com 12.3 Install the system in a hidden place. 12.4 Avoid getting water into the Control Unit. 12.5 Have a secure connection to the main power supply and provide good ventilation.. 12.6 This product was designed for the indoor use. 12.7 Opening the control unit cover will void the warranty. 13. Maintenance 13.1 In case of failure, please contact the distributor or manufacturer. 13.
Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com Warranty Card Model ______________ Product ID ___________ Date of Purchase__________________ Date of Production___________________ Maintenance Record __________________________________________________ __________________________________________________ __________________________________________________ Dealer _____________________________ Page ３４ of 35 Ver 2.
