Technical data

ST605
Heating Tips Used in Welding Handles
Smith’s multi-flame and single flame heating tips are designed to provide large
volumes of heat for applications such as: heat treating, bending, straightening,
pre-heating, brazing, shrinking, forming and many others. Smaller sizes are often
used for braze welding or for applying hard facing metal to large areas. Heating tips provide significant cost savings in many
applications. By providing great amounts of quick, concentrated heat, heating tips do the job faster and cut labor time to a minimum. For
proper performance, use the recommended pressures for each tip and with an adequate gas supply. Manifolding of cylinders is essential
for safe and efficient operation of large size heating tips.
Heating Tips
Heavy Duty / Oxy-Acetylene
43
Tips
MT605
Medium Duty / Oxy-Acetylene
Standard Duty Acetylene
Actual Size Tip
Actual Size Tips
CAUTION: Heating tips must be used in conjunction with high flow flashback arrestors. It may be necessary to increase outlet pressures
to compensate for flow restrictions that may be created by flashback arrestors.
AT605
Handy light duty multi-flame tip for heating, brazing and applying
hard facing metals. Uses medium pressure acetylene and oxygen.
USED IN:
Torch Handles - AW1A & AW10A.
MT603 MT605 MT610
Stock No. of Drill Pressures (PSIG) Consumption (SCFH) Average Fuel * Overall Length
No. Flames Size Oxygen Fuel Gas Oxygen Fuel Gas BTU Cylinders Required Inches/mm
AT605 6 #64 10 15 32 29 41,550 1 10”/254
NOTE: Tips may also be used with oxygen/hydrogen.
* Require minimum 200 cu. ft. acetylene cylinder size.
Versatile multi-flame heating tips for the popular medium duty torch handles. Used for
general heating of metals, brazing, hard surfacing, etc. Heads are manufactured from
solid copper.
USED IN:
Torch Handles - WH100, MW5A & CW5A.
Stock No. of Drill Pressures (PSIG) Consumption (SCFH) Average Fuel Overall Length
No. Flames Size Oxygen Fuel Gas Oxygen Fuel Gas BTU Cylinders Required Inches/mm
MT603 6 #64 10 15 31 28 40,125 1 10”/254
MT605 6 #56 10 15 57 51 73,085 **1 16”/406
MT610 12 #57 10 15 100 90 128,970 **2 18”/457
**NOTE: 350 cubic foot minimum cylinder @ 70˚ F. NOTE: Tips may also be used with oxygen/hydrogen.
WARNING! MANIFOLDING CYLINDERS: When required flows (cubic feet per hour - SCFH) exceed the
recommended withdrawal rate from one cylinder then additional cylinders must be manifolded to provide safe and efficient
operation. Acetylene must not be withdrawn at more than 1/7 of the cylinder capacity (50 SCFH for a 350 cu. ft. cylinder).
Consult your gas supplier for manifolding instructions for the gases and cylinders supplied to you. Refer to Technical Data
on website.
Stock No. of Drill Pressures (PSIG) Consumption (SCFH) Average Fuel ** Overall Length
No. Flames Size Oxygen Fuel Gas Oxygen Fuel Gas BTU Cylinders Required Inches/mm
ST602 6 #64 10 10 31 28 40,125 1 16” / 406
ST603 6 #56 15 15 55 50 71,750 1 16” / 406
ST605 12 #57 15 15 96 87 124,670 2 19” / 483
ST610 12 #54 15 15 150 136 194,890 3 19” / 483
**NOTE: 350 cubic foot minimum cylinder size @ 70˚ F. /
USED IN: Torch Handles - SW1A, SW1B & WH200.
ST603 ST605 ST610
Actual Size Tips