Technical data

36
Tips
Cutting Tips
Heavy Duty “SC” / Propylene (Also propylene based fuel gases)
SC60 Series Oxy-Propylene
Two-piece medium preheat cutting tips designed to provide optimum
performance with propylene or propylene base fuel gases.
USE IN: Cutting Attachments - DG200 & SC200 Series
(Maximum size SC60-5).
All SC & DG Series Hand Torches .
2-Hose Machine Cutting Torches (Maximum size SC60-6).
All 3-Hose Machine Cutting Torches.
SC60 Series Medium Preheat
Two-Piece
General Gouging
SC2-2
Heating
SC112
Gouging
SC23-3
SC23-3M
General Gouging - SC2-2 & SC2-4 Oxy-Propane
For removing old welds or cracks, for veeing and groove cutting.
Heating - SC112 Oxy-Propane
Provides lots of heat fast with economical LP Gas and Oxygen.
Not recommended for use in cutting assemblies.
Gouging, Heavy Duty - SC23-3 Oxy-Propane
Gouging, Heavy Duty - SC23-3M Oxy-Propylene
For removing old welds or cracks, for veeing and groove cutting.
Use In: DG200 & SC200 Series Cutting Attachments (Except SC112). All SC & DG Series Hand Torches & Machine Torches.
Tip Oxy Fuel Gas Oxy Fuel Oxy Drill Fuel Gas
Number Purpose Capacity (inches) Capacity (mm) Fuel Gas Pressure Pressure Consumption Consumption Size Configuration
SC2-2 Gouging 5/16” wide 8 wide Propane 60 22 389 53 53 Slots
(General) x 1/8” deep x 3 deep 31
SC2-4 Gouging 3/8” wide 10 wide Propane 75 22 564 53 44 Slots
(General) x 1/4” deep x 6 deep 28
SC112 Heating 289,000 BTU’s N/A Propane 60 25 495 125 * N/A Slots
SC23-3 Gouging 3/8” wide 10 wide Propane 50-60 12-18 174 31 50 Slots
(Heavy) x 1/4” deep x 6 deep
SC23-3M Gouging 1/4” wide 6 wide Propylene 50-60 10-15 174 31 50 Slots
x 3/8” deep x 10 deep
* 2 cylinders required - based on 100 lb. cylinders.
Heavy Duty “SC” Special Purpose / LP Gas
Pressure - PSIG Consumption - SCFH Drill Size
Tip Metal Thickness Cutting Oxygen Preheat PSI Kerf Oxygen Propylene Speed Cutting
Number Inches mm Reg. Torch Oxy Propylene Width Cutting Preheat Preheat I.P.M. Jet
SC60-0 1/4” 6 30 30 10† 10 .053 40 38 9 22 62
SC60-0 3/8” 10 35 35 10† 10 .055 50 38 9 20 62
SC60-1 1/2” 13 35 35 10† 10 .080 75 38 9 19 56
SC60-1 5/8” 16 40 40 10† 10 .080 85 38 9 17 56
SC60-2 3/4” 19 36 35 10† 10 .095 105 38 9 16 54
SC60-2 1” 25.4 41 40 10† 10 .095 115 38 9 14 54
SC60-2 1 1/4” 32 51 50 10† 10 .095 135 38 9 13 54
SC60-3 1 1/2” 38 42 40 10† 10 .100 170 38 9 12 51
SC60-3 2” 51 47 45 10† 10 .100 180 38 9 10 51
SC60-4 2 1/2” 64 38 35 12† 10 .125 240 58 15 9 45
SC60-4 3” 76 44 40 12† 10 .125 265 58 15 8 45
SC60-4 4” 102 54 50 12† 10 .125 315 58 15 7 45
SC60-5 5” 127 56 50 12† 10 .150 420 58 15 7 41
SC60-5 6” 153 67 60 12† 10 .150 485 58 15 6 41
SC60-5 8” 203 78 70 12† 10 .150 550 58 15 5 41
SC60-6 10” 254 83 70 12† 10 .230 750 58 15 5 32
SC60-6 12” 305 125 90 12† 10 .230 975 58 15 4.5 32
† Listed pressure for 3-hose machine cutting torches only.