Technical data

Pressure - PSIG Consumption - SCFH Drill Size
Tip Metal Thickness Cutting Oxygen Preheat Kerf Oxygen Fuel Speed Cutting
Number Inches mm Reg. Torch Oxy Acety. Width Cutting Preheat Preheat I.P.M. Jet Preheat
SC12-00 3/16" 5 20 20 10† 10 .050 24 7 6.5 26 68 75
SC12-0 1/4” 6 30 30 10† 10 .055 40 7.5 7 22 62 74
SC12-0 3/8” 10 35 35 10† 10 .055 50 7.5 7 20 62 74
SC12-1 1/2” 13 35 35 10† 10 .080 75 11 9.5 19 56 71
SC12-1 5/8” 16 40 40 10† 10 .080 85 11 9.5 17 56 71
SC12-2 3/4” 19 36 35 10† 10 .095 105 12 10.5 16 54 70
SC12-2 1” 25 41 40 10† 10 .095 115 12 10.5 14 54 70
SC12-2 1-1/4” 32 51 50 10† 10 .095 135 12 10.5 13 54 70
SC12-3 1-1/2” 38 42 40 10† 10 .100 170 14 12 12 51 68
SC12-3 2” 51 47 45 10† 10 .100 180 14 12 10 51 68
SC12-4 2-1/2” 64 38 35 10† 10 .125 240 15 13 9 45 62
SC12-4 3” 76 44 40 10† 10 .125 265 15 13 8 45 62
SC12-4 4” 102 54 50 10† 10 .125 315 16 14 7 45 62
SC12-5 5” 127 56 50 10† 10 .150 420 30 26* 7 41 57
SC12-5 6” 152 67 60 10† 10 .150 485 30 26* 6 41 57
SC12-5 8” 203 78 70 10† 10 .150 550 30 26* 5.5 41 57
SC12-6 10” 254 83 70 10† 10 .230 750 32 28* 5 32 57
SC12-6 12” 305 125 90 10† 10 .230 975 32 28* 4.5 32 57
32
SC12 Series
Cutting Tips
Heavy Duty “SC” Acetylene
Heavy Duty “SC” Acetylene
SC12 Series Oxy-Acetylene
Six preheat cutting tips for general hand and machine cutting.
Provides excellent preheat characteristics required for machine cutting.
Oxy-Acetylene
SC56 Series Heavy Preheat
Heavy preheat cutting tips designed for cutting coated metals, heavy piercing, fast
preheating and cutting thick steel sections up to 24” (610mm).
USE IN: Cutting Attachments - DG200 & SC200 Series
(Maximum size SC56-5).
All SC & DG Series Hand Torches .
2-Hose Machine Cutting Torches (Maximum size SC56-7). 3-Hose Machine Cutting Torch.
† Listed pressure for 3-hose machine cutting torches only. * Minimum of one 350 cu. ft. cylinder required.
WARNING: High gas withdrawal rates will require cylinder manifolding. Consult your gas supplier.
† Listed pressure for 3-hose machine cutting torches only. Pressures shown are for 25’ (7.6m) or less of
3
/
8
” (10mm) I.D. hose. Increase pressures if longer
hose is used. Use
1
/
2
” (13mm) I.D. hose when hose length exceeds 100’ (31m). * Cylinders required, based on 350 cu. ft. cylinder
Tips
Heavy Duty Cutting
SC56 Series
Pressure - PSIG Consumption - SCFH Drill Size Recm’d
Tip Metal Thickness Cutting Oxygen Preheat PSI Kerf Oxygen Fuel Speed Cutting Preheat No. of
Number Inches mm Reg. Torch Oxy Fuel Width Cutting Preheat Preheat I.P.M. Jet Cylinders*
SC56-1 1/2” 13 35 35 10† 10 .080 75 33 30 19 56 65 1
SC56-1 5/8” 16 40 40 10† 10 .080 85 33 30 17 56 65 1
SC56-2 3/4” 19 36 35 10† 10 .095 105 33 30 16 54 60 1
SC56-2 1” 25 41 40 10† 10 .095 115 33 30 14 54 60 1
SC56-2 1-1/4” 32 51 50 10† 10 .095 135 33 30 13 54 60 1
SC56-3 1-1/2” 38 42 40 10† 10 .100 170 43 39 12 51 57 1
SC56-3 2” 51 47 45 10† 10 .100 180 50 45 10 51 57 1
SC56-5 2" - 5” 127 56 50 10† 10 .150 420 57 52 7 41 54 2
SC56-5 6” 152 67 60 10† 10 .150 485 66 60 6 41 54 2
SC56-5 8” 203 78 70 10† 10 .150 550 72 65 5.5 41 54 2
SC56-7 8" - 14” 356 100 85 10† 10 .250 1250 110 100 4 28 54 2
SC56-9 14" - 20” 508 110 70 14† 12 .350 2150 145 130 3 3 54 3
SC56-9 24” 610 130 85 15† 13 .360 2600 175 160 2.5 3 54 4
USE IN: Cutting Attachments - DG200 & SC200 Series
(Maximum size SC12-5).
All SC & DG Series Hand Torches . All Machine Torches .