Product Manual
Table Of Contents
- 1. Getting started
- 2. Recording an exercise ECG
- 2.1 The Real-time monitor
- 2.2 Record an exercise ECG
- 2.3 Real-time monitor
- 2.3.1. Select how you want to view leads
- 2.3.2. Measure blood pressure
- 2.3.3. Capture an event
- 2.3.4. Patient Perception Parameters
- 2.3.5. Duke Treadmill Score
- 2.3.6. Add a comment
- 2.3.7. Apply filters
- 2.3.8. Manual load change
- 2.3.9. Pacemaker pulse detection
- 2.3.10. Signal quality indication
- 2.3.11. Printing during recording
- 2.3.12. Target heart rate
- 2.3.13. Target Workload
- 3. Viewing an exercise ECG
- 3.1 About viewing exercise ECGs
- 3.2 View an exercise ECG
- 3.3 Work with the Summary view
- 3.4 Work with the Averages view
- 3.5 Work with the Full disclosure view
- 3.6 Work with the 2x6 and 4x3 view
- 3.7 Work with the Trends view
- 3.8 Work with the ST table view
- 3.9 Work with the Heart rate view
- 3.10 Work with the ST/HR view
- 4. Interpreting an exercise ECG
- 5. Printing an exercise ECG
- 6. Maintaining the recorder
- 7. Customizing the Exercise ECG module
- 8. Customize exercise protocols
- 9. Troubleshooting
- 10. Before installing the Exercise ECG software
- 11. Installing the Exercise ECG Module
- 12. Safety and precautions
- 13. Guidance and Manufacturer’s Declarations
- 14. Function keys
- 15. Additional information
CardioPerfect Workstation
Exercise ECG Module - User Manual
To replace the battery of Welch Allyn CardioPerfect MD models:
The battery compartment is located at the bottom of the unit.
1. Place your fingers in the two recesses of the battery compartment.
2. Remove the lid by squeezing it.
3. Unfasten and remove the battery.
4. Insert a new 9V alkaline battery.
5. Click the lid back into place.
After you have replaced the batteries, let the Welch Allyn CardioPerfect software run in
Monitor mode for a few seconds. This verifies that the recorder functions properly and the
optical cable is undamaged.
Warning
It is strictly forbidden to use a non-medical approved 9V AC
mains adapter, because of patient safety.
Caution
Please observe the following:
We advise you not to use rechargeable batteries, because their
voltage can drop steeply without warning. This can stop the ECG
monitoring during a test.
6.3.2. Welch Allyn CardioPerfect Pro recorders
The Welch Allyn CardioPerfect Pro recorders get their power either via a USB connection or
via a rechargeable battery. If a USB-Prolink is used, the Welch Allyn CardioPerfect Pro
recorder gets its power from the USB port of the computer, the battery pack supplied with the
recorder is then a so-called dummy.
If the recorder is connected to the computer by means of an RS232 Prolink, the power is
supplied by a battery-pack in the bottom of the recorder, this battery pack needs to be
recharged (charger is supplied with the system) when the indicator turns red.
Caution
If the recorder is powered from the USB port, but also has a
battery pack, this battery will be drained slowly as well and if the
recorder detects an empty battery it will not function until the
battery is recharged or removed.
After you have replaced or charged (Pro) the batteries, let the Welch Allyn CardioPerfect
software run in Monitor mode for a few seconds. This verifies that the recorder functions
properly.
DIR 80012335 Ver. D 46 / 83