Approval/Certificate/Document of Conformity

Job Id: 262.1-024252-2
Certificate No: TAA000016Z
Revision No: 3
Form code: TA 251
Revision: 2016-12
www.dnvgl.com
Page 3 of 4
1527940000
ZQV 4N/3
Cross-connector, No. of poles: 3
58452 1
-
1528080000
ZQV 4N/3 BL
Cross-connector, No. of poles: 3
58452 1
-
2460810000
ZQV 4N/3 RD
Cross-connector, No. of poles: 3
58452 1
-
1527970000
ZQV 4N/4
Cross-connector, No. of poles: 4
58452 1
-
1528120000
ZQV 4N/4 BL
Cross-connector, No. of poles: 4
58452 1
-
2460800000
ZQV 4N/4 RD
Cross-connector, No. of poles: 4
58452 1
-
1527980000
ZQV 4N/5
Cross-connector, No. of poles: 5
58452 1
-
1528140000
ZQV 4N/5 BL
Cross-connector, No. of poles: 5
58452 1
-
2460790000
ZQV 4N/5 RD
Cross-connector, No. of poles: 5
58452 1
-
1528130000
ZQV 4N/50
Cross-connector, No. of poles: 50
63074 2
-
1528240000
ZQV 4N/50 BL
Cross-connector, No. of poles: 50
63074 2
-
2426730000
ZQV 4N/50RD
Cross-connector, No. of poles: 50
63074 2
-
1527990000
ZQV 4N/6
Cross-connector, No. of poles: 6
58452 1
-
1528170000
ZQV 4N/6 BL
Cross-connector, No. of poles: 6
58452 1
-
2460780000
ZQV 4N/6 RD
Cross-connector, No. of poles: 6
58452 1
-
1528020000
ZQV 4N/7
Cross-connector, No. of poles: 7
58452 1
-
1528180000
ZQV 4N/7 BL
Cross-connector, No. of poles: 7
58452 1
-
2460770000
ZQV 4N/7 RD
Cross-connector, No. of poles: 7
58452 1
-
1528030000
ZQV 4N/8
Cross-connector, No. of poles: 8
58452 1
-
1528190000
ZQV 4N/8 BL
Cross-connector, No. of poles: 8
58452 1
-
2460760000
ZQV 4N/8 RD
Cross-connector, No. of poles: 8
58452 1
-
1528070000
ZQV 4N/9
Cross-connector, No. of poles: 9
58452 1
-
1528220000
ZQV 4N/9 BL
Cross-connector, No. of poles: 9
58452 1
-
2460750000
ZQV 4N/9 RD
Cross-connector, No. of poles: 9
58452 1
-
Application/Limitation
The Type Approval covers hardware listed under Product description.
When the hardware is used in applications to be classed by DNV GL, documentation for the actual
application is to be submitted for approval by the manufacturer of the application system in each case.
Reference is made to DNV GL RU SHIP Pt.4 Ch.9 Sec. 1.
The installation instructions are to be observed.
The system must be operated with 24 V DC (18...30 V DC) safety extra-low voltage (SELV) or protective
extra-low voltage (PELV).
Ex-certification is not covered by this certificate. Application in hazardous area to be approved in each
case according to the Rules and Ex-Certification/ Special Condition for Safe Use listed in valid Ex-
Certificates issued by a notified/recognized Certification Body.
Safe Distance to the
Reduced Safe Distance to the
Standard-Magnetic-Compass
1.60m
1.00m
Steering-Magnetic-Compass
1.00m
0.60m
Product certificate
If specified in the Rules, ref. Pt.4 Ch.9 Sec.1, the control and monitoring system in which the above
listed hardware is used shall be delivered with a product certificate. For each such delivery the
certification test is to be performed at the manufacturer of the application system before the system is
shipped to the yard. The test shall be done according to an approved test program. After the certification
the clause for application software control will be put into force.
Clause for application software control
All changes in software are to be recorded as long as the system is in use on board. The records of all
changes are to be forwarded to DNVGL for evaluation and approval. Major changes in the software are to
be approved before being installed in the computer.