User Documentation

ManualsBrandsWeidmueller ManualsAutomation & SoftwareUC20-SL2000-EC Currently only available in combination with Runtime-License (2638920000).

Table Of Contents

Table of contents
1 Introduction
- 1.1 Purpose of the document
- 1.2 Requirements
- 1.3 Intended use
- 1.4 Notes on this document
  - 1.4.1 Contents of the document
  - 1.4.2 Not contained in this document
- 1.5 Further documentation
- 1.6 Relevant countries and registrations
2 Safety instructions
- 2.1 Representation
- 2.2 General safety information
- 2.3 Personnel safety
- 2.4 Safety instructions for projecting
3 System overview
- 3.1 Hardware architecture
- 3.2 Software structure
- 3.3 Network design
- 3.4 u-control - CPU modules
- 3.5 Buses
- 3.6 u-create studio Toolsuite
- 3.7 Libraries and interfaces
4 Operating behavior
- 4.1 Start-up
5 Software installation
- 5.1 Install firmware of the control
6 Configuration
- 6.1 Data exchange between control and visualization
7 Program development
- 7.1 Task priorities
- 7.2 Fast control
- 7.3 Device Service
8 Licensing
- 8.1 Trial license
  - 8.1.1 Activation of a trial license (single user license)
  - 8.1.2 Activation of a trial license (runtime license)
- 8.2 Activating a single-user license (software on the PC)
- 8.3 Activating a runtime license (software on the device)
- 8.4 License status and license overview
- 8.5 Device replacement
  - 8.5.1 PC replacement (single-user license)
  - 8.5.2 Device replacement (runtime license)
- 8.6 Reset the license information
9 Device Administration (DevAdmin)
- 9.1 Tab "Diag."
- 9.2 Tab "Config."
- 9.3 Tab "Backup/Restore"
- 9.4 Tab "Plugins"
  - 9.4.1 Add plugin to DevAdmin
- 9.5 Change password for DevAdmin
10 Software units
- 10.1 Creating a software unit
- 10.2 Example meta.xml
11 OPC UA Server
- 11.1 Overview of variants
- 11.2 Establishing a connection
- 11.3 Server configuration
- 11.4 Generic variable tree
- 11.5 Creating an information model
- 11.6 Logging of server operation
12 Node-RED
13 LongtermDiagnosticMonitor
- 13.1 Monitor
14 Data recorder
- 14.1 Configuration
- 14.2 Data recording
- 14.3 Reading out the buffer
- 14.4 Recording callback from the application
- 14.5 Data locality and real-time
- 14.6 Size limitations
- 14.7 Appendix: C interface
15 Diagnostics
- 15.1 Control diagnosis
  - 15.1.1 Error codes
- 15.2 Diagnosis data for Weidmüller
  - 15.2.1 Status report
  - 15.2.2 Access to flash storage medium
- 15.3 USB via Ethernet adapter
16 Maintenance
- 16.1 Executing a firmware update of the system components
  - 16.1.1 Firmware-Update for devices
  - 16.1.2 Automatic update during boot-up
17 Technical data
18 Directives and standards
19 Appendix: Tutorial - creating an IEC project
- 19.1 Creating a new project
- 19.2 Creating a simple program
- 19.3 Saving u-create studio project
- 19.4 Load firmware onto device
- 19.5 Configuration of the control
- 19.6 Compiling project and uploading onto control
- 19.7 Starting the project
20 Appendix: Addressing in the Ethernet (basics)
21 Appendix: Tutorial FoE
22 Appendix: Tutorial - call C function from IEC
- 22.1 Preconditions and needed components
- 22.2 Task
- 22.3 Creating the C function and download
- 22.4 Calling the IEC funtion in the IEC application and download
Index

Device Administration (DevAdmin)

System manual

2696790000/02/04.2020

Fig.9-7: DevAdmin - Diagnostics

Area "Device Information"

In this area the following information of the used control are displayed:

Information Description

Device Name Designation of the control

Ser.No. Serial number of the control

Part No. Material number of the control

Rev. Revision number of the control

Operating Hours Operating hours of the control

Workload Current utilization of the control

Temperature Current temperature of the control

Battery State of the battery

Area "Device State"

In this area the following information of the used control are displayed: