User Documentation

ManualsBrandsWeidmueller ManualsAutomation & SoftwareUC20-SL2000-EC Currently only available in combination with Runtime-License (2638920000).

Table Of Contents

Table of contents
1 Introduction
- 1.1 Purpose of the document
- 1.2 Requirements
- 1.3 Intended use
- 1.4 Notes on this document
  - 1.4.1 Contents of the document
  - 1.4.2 Not contained in this document
- 1.5 Further documentation
- 1.6 Relevant countries and registrations
2 Safety instructions
- 2.1 Representation
- 2.2 General safety information
- 2.3 Personnel safety
- 2.4 Safety instructions for projecting
3 System overview
- 3.1 Hardware architecture
- 3.2 Software structure
- 3.3 Network design
- 3.4 u-control - CPU modules
- 3.5 Buses
- 3.6 u-create studio Toolsuite
- 3.7 Libraries and interfaces
4 Operating behavior
- 4.1 Start-up
5 Software installation
- 5.1 Install firmware of the control
6 Configuration
- 6.1 Data exchange between control and visualization
7 Program development
- 7.1 Task priorities
- 7.2 Fast control
- 7.3 Device Service
8 Licensing
- 8.1 Trial license
  - 8.1.1 Activation of a trial license (single user license)
  - 8.1.2 Activation of a trial license (runtime license)
- 8.2 Activating a single-user license (software on the PC)
- 8.3 Activating a runtime license (software on the device)
- 8.4 License status and license overview
- 8.5 Device replacement
  - 8.5.1 PC replacement (single-user license)
  - 8.5.2 Device replacement (runtime license)
- 8.6 Reset the license information
9 Device Administration (DevAdmin)
- 9.1 Tab "Diag."
- 9.2 Tab "Config."
- 9.3 Tab "Backup/Restore"
- 9.4 Tab "Plugins"
  - 9.4.1 Add plugin to DevAdmin
- 9.5 Change password for DevAdmin
10 Software units
- 10.1 Creating a software unit
- 10.2 Example meta.xml
11 OPC UA Server
- 11.1 Overview of variants
- 11.2 Establishing a connection
- 11.3 Server configuration
- 11.4 Generic variable tree
- 11.5 Creating an information model
- 11.6 Logging of server operation
12 Node-RED
13 LongtermDiagnosticMonitor
- 13.1 Monitor
14 Data recorder
- 14.1 Configuration
- 14.2 Data recording
- 14.3 Reading out the buffer
- 14.4 Recording callback from the application
- 14.5 Data locality and real-time
- 14.6 Size limitations
- 14.7 Appendix: C interface
15 Diagnostics
- 15.1 Control diagnosis
  - 15.1.1 Error codes
- 15.2 Diagnosis data for Weidmüller
  - 15.2.1 Status report
  - 15.2.2 Access to flash storage medium
- 15.3 USB via Ethernet adapter
16 Maintenance
- 16.1 Executing a firmware update of the system components
  - 16.1.1 Firmware-Update for devices
  - 16.1.2 Automatic update during boot-up
17 Technical data
18 Directives and standards
19 Appendix: Tutorial - creating an IEC project
- 19.1 Creating a new project
- 19.2 Creating a simple program
- 19.3 Saving u-create studio project
- 19.4 Load firmware onto device
- 19.5 Configuration of the control
- 19.6 Compiling project and uploading onto control
- 19.7 Starting the project
20 Appendix: Addressing in the Ethernet (basics)
21 Appendix: Tutorial FoE
22 Appendix: Tutorial - call C function from IEC
- 22.1 Preconditions and needed components
- 22.2 Task
- 22.3 Creating the C function and download
- 22.4 Calling the IEC funtion in the IEC application and download
Index

Safety instructions

System manual

2696790000/02/04.2020

2.2 General safety information

The documentation contains the information required to plan the use of u-

create studio with UC20-SL2000-EC or UC20-SL2000-EC-CAN.

Familiarity with and correct application of the information contained in these

manuals is a prerequisite for successful planning and safe installation, com-

missioning and maintenance of automation systems. Only qualified persons

have the required technical expertise for correct interpretation and imple-

mentation of the instructions in these documents.

For reasons of clarity, not every single detail of every version of the products

described is listed nor can every practical situation be taken into considera-

tion. If you need further information, please request this from Weidmüller.

When installing, commissioning and servicing u-create products, the instruc-

tions given in the relevant part of the documentation must be observed.

2.3 Personnel safety

WARNING!

Unqualified interventions in the control may cause abnormal behavior of the

machine/plant or personal injury or damage to the equipment. Only specially

qualified staff may carry out activities on the control system.

2.4 Safety instructions for projecting

CAUTION!

● The instructions contained in the further delivered must be precisely fol-

lowed in all circumstances. Failure to do so could result in the creation of

potential sources of danger or the disabling of protective circuits inte-

grated in the u-create system.

● Apart from the safety instructions given in these manuals, safety precau-

tions and accident prevention measures appropriate to the situation in

question must also be observed.

● Measures must be taken to ensure that in the event of power dips or

power failures, an interrupted program can be properly restarted. In such

situations, dangerous operating conditions must not be allowed to occur

even temporarily.

● In all situations where faults occurring on the automation system could

cause personal injury or significant damage to machinery and equip-

ment, additional external safety measures must be taken in order to en-

sure the system as a whole remains in a safe operating condition even

in the event of a fault.