User Documentation

ManualsBrandsWeidmueller ManualsAutomation & SoftwareUC20-SL2000-EC Currently only available in combination with Runtime-License (2638920000).

101

102

103

104

105

106

107

108

109

110

Table Of Contents

Table of contents
1 Introduction
- 1.1 Purpose of the document
- 1.2 Requirements
- 1.3 Intended use
- 1.4 Notes on this document
  - 1.4.1 Contents of the document
  - 1.4.2 Not contained in this document
- 1.5 Further documentation
- 1.6 Relevant countries and registrations
2 Safety instructions
- 2.1 Representation
- 2.2 General safety information
- 2.3 Personnel safety
- 2.4 Safety instructions for projecting
3 System overview
- 3.1 Hardware architecture
- 3.2 Software structure
- 3.3 Network design
- 3.4 u-control - CPU modules
- 3.5 Buses
- 3.6 u-create studio Toolsuite
- 3.7 Libraries and interfaces
4 Operating behavior
- 4.1 Start-up
5 Software installation
- 5.1 Install firmware of the control
6 Configuration
- 6.1 Data exchange between control and visualization
7 Program development
- 7.1 Task priorities
- 7.2 Fast control
- 7.3 Device Service
8 Licensing
- 8.1 Trial license
  - 8.1.1 Activation of a trial license (single user license)
  - 8.1.2 Activation of a trial license (runtime license)
- 8.2 Activating a single-user license (software on the PC)
- 8.3 Activating a runtime license (software on the device)
- 8.4 License status and license overview
- 8.5 Device replacement
  - 8.5.1 PC replacement (single-user license)
  - 8.5.2 Device replacement (runtime license)
- 8.6 Reset the license information
9 Device Administration (DevAdmin)
- 9.1 Tab "Diag."
- 9.2 Tab "Config."
- 9.3 Tab "Backup/Restore"
- 9.4 Tab "Plugins"
  - 9.4.1 Add plugin to DevAdmin
- 9.5 Change password for DevAdmin
10 Software units
- 10.1 Creating a software unit
- 10.2 Example meta.xml
11 OPC UA Server
- 11.1 Overview of variants
- 11.2 Establishing a connection
- 11.3 Server configuration
- 11.4 Generic variable tree
- 11.5 Creating an information model
- 11.6 Logging of server operation
12 Node-RED
13 LongtermDiagnosticMonitor
- 13.1 Monitor
14 Data recorder
- 14.1 Configuration
- 14.2 Data recording
- 14.3 Reading out the buffer
- 14.4 Recording callback from the application
- 14.5 Data locality and real-time
- 14.6 Size limitations
- 14.7 Appendix: C interface
15 Diagnostics
- 15.1 Control diagnosis
  - 15.1.1 Error codes
- 15.2 Diagnosis data for Weidmüller
  - 15.2.1 Status report
  - 15.2.2 Access to flash storage medium
- 15.3 USB via Ethernet adapter
16 Maintenance
- 16.1 Executing a firmware update of the system components
  - 16.1.1 Firmware-Update for devices
  - 16.1.2 Automatic update during boot-up
17 Technical data
18 Directives and standards
19 Appendix: Tutorial - creating an IEC project
- 19.1 Creating a new project
- 19.2 Creating a simple program
- 19.3 Saving u-create studio project
- 19.4 Load firmware onto device
- 19.5 Configuration of the control
- 19.6 Compiling project and uploading onto control
- 19.7 Starting the project
20 Appendix: Addressing in the Ethernet (basics)
21 Appendix: Tutorial FoE
22 Appendix: Tutorial - call C function from IEC
- 22.1 Preconditions and needed components
- 22.2 Task
- 22.3 Creating the C function and download
- 22.4 Calling the IEC funtion in the IEC application and download
Index

Maintenance

System manual

2696790000/02/04.2020

104

16.1.1 Firmware-Update for devices

This chapter describes the creation of a storage medium to execute a

firmware update of the control.

To create a firmware update on a storage medium proceed as follows:

1) Start firmware update tool via double-clicking "u-create FirmwareUp-

date.exe".

2) Confirm the following dialogue with "Next".

3) Select the desired device from the list "devices".

Press "show components" to show all software components, for which

an update is available, in the list "components".

4) Select the desired update and transfer it to the list "selection" via >>.

5) Remove one or several updates from the list "selection" via << or "<<

unselect all devices".

6) To create updates for several devices, repeat step 4 and 5.

Confirm with "Next".

7) Select the root directory of the connected storage medium and confirm

with "Next".

8) The following configuration dialogue opens:

updateReference ... The update data will be additionally stored on the device.