User Documentation

4 5 6 V1.0 / 2020-11-02
8. Wiring Redundant Power Inputs
The switch supports redundant power supply inputs. For wiring via 6-pin terminal
connector please refer to below illustration.
Warning / Avertissement
 Take into consideration the following guidelines before wiring the device
o Tenez compte des directrices suivantes avant de câbler l’appareil.
 Terminal block is mating with Plug and suitable for 12-24AWG. Torque
value 4.5 lb-in.
o Le bornier est compatible avec les connecteurs et convient pour 12-
24AWG. Valeur de couple 4,5 lb-in.
 The temperature rating of the input connection cable should higher than
105°C.
o La température de service nominale du câble d’entrée doit être
supérieure à 105 °C.
 Supplied by SELV source evaluated by UL 61010-1 or 61010-2-201
power supply only.
o Fourni par la source SELV évaluée uniquement par l'alimentation UL
61010-1 or 61010-2-201.
9. Communication Connections
Switch IE-SW-EL16-14TX-2FESFP is equipped with following communication interfaces:
14x 10/100Base-T(X) ports
2x 100Base-FX SFP slots to be used with SFP Transceivers (mini-GBIC
Please only use cables suitable for the respective type of communication and ensure that
signals are protected from possible interference.
9.1 10/100Base T(X) RJ45 Ports
The 10/100BaseT(X) ports located on Ethernet Switch’s front panel are used to connect
to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type) ports and
MDI-X (HUB/Switch-type) ports. Auto MDI-X ensures that both wiring-schemes are
supported (Automatic crossover function).
10/100Base T(X) RJ45 Pinouts
MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45
Pin Signal Pin Signal
1 Tx+ 1 Rx+
2 Tx- 2 Rx-
3 Rx+ 3 Tx+
6 Rx- 6 Tx-
9.2 100Base-FX SFP (mini-GBIC) Fiber Port
The 100Base-FX type slots, require 100Base-FX SFP (mini-GBIC) fiber transceivers to
work properly. Weidmüller provides transceiver models for various distance requirements.
Please only use SFP modules and cables that are compatible with each other to establish
an optical connection.
LC-Port with separate Transmit and Receive Port:
Remember to connect the Tx (transmit) port of device I to the Rx (receive) port of device
II, and the Rx (receive) port of device I to the Tx (transmit) port of device I
LC-Port Pinouts LC-Port to LC-Port Cable Wiring
Note about possible loss of data packages in case of “Duplex mismatching”
If the switch’s auto-negotiation port is connected to a non-negotiating device,
then the switch will set its port transmission speed same as the connected
device but is unable to correctly detect the duplex mode.
As result the port is set to the correct speed but is using always the half duplex
mode as required by the IEEE 802.3u standard in such cases.
For correct transmission, the non-negotiating port must be set to half-duplex
mode (speed can be either 10 Mbps or 100 Mbps, it always will be recognized
automatically by an Auto-Negotiation-Device).
10. LED Indicators
The front panel of the Ethernet Switch contains several LED indicators. The function of
each LED is described in the table below.
LED Color Status Description
PWR1 Green
On
Power is being supplied to power input
PWR1.
Off
Power is not being supplied to power input
PWR1.
PWR2 Green
On
Power is being supplied to power input
PWR2.
Off
Power is not being supplied to power input
PWR2.
LNK/ACT
(RJ45 LAN
Ports)
Green
On Port link is active.
Off Port link is inactive.
Blinking Transmitting data.
10/100M
(RJ45 LAN
Ports)
Amber
On Port speed is 100 Mbps.
Off Port speed is 10 Mbps.
100M
(Fiber Port 15-
16)
Green
On Port link is active.
Off Port link is inactive.
Blinking Transmitting data.
11. Specifications
Technology
Standards
IEEE 802.3 for 10Base-T,
IEEE 802.3u for 100BaseTX and 100BaseFX
IEEE 802.3x flow control
Processing Type Store and Forward
MAC Table size 4K
Packet buffer size 2.75 Mbit
Backplane bandwidth 3.2 Gbps
Interfaces
RJ45 Ports
10/100BaseT(X) auto negotiation speed, Full/Half duplex
mode and auto MDI/MDI-X connection
Fiber optic Port 100BaseSFP slot
LED Indicators
PWR1, PWR2 (Power), LAN Port Link/Activity and Port
speed, SFP Port Link/Activity
Power
Input Voltage 24 V DC (12 - 48 V DC) ,2 redundant inputs
Input Current @24 VDC 0.34 A
Connection One removable 6-pin terminal block, Wiring cable 12-24AWG
Overload Current
Protection
Present
Reverse Polarity
Protection
Present
Physical Characteristics
Housing IP30 protection, metal
Dimension (W x H x D) 74 x 170 x 140 mm (2.91 x 6.69 x 5.51 in)
Weight 1120 g
Installation DIN-rail
Environmental conditions
Operating Temperature -40 to 75°C (-40 to 167°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity
5 to 95% (non-condensing)
Altitude up to 2000 m
Regulatory Approvals
Safety UL 61010-1; UL 61010-2-201
EMC
EN 55032, EN 55024, FCC Part 15 Subpart B Class A
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV,
IEC 61000-4-3 RS: 80 MHz to 1 Ghz: 3 V/m,
IEC 61000-4-4 EFT: Power: 0.5 kV; Signal: 0.5 kV,
IEC 61000-4-5 Surge: Power: 0.5 kV; Signal: 1 kV,
IEC 61000-4-6 CS: 3 Vrms
Shock IEC 60068-2-27
Free Fall IEC 60068-2-31
Vibration IEC 60068-2-6
MTBF
Time 719.800 hrs
Database Telcordia SR332
Warranty
Time Period 5 years
Contact Information
Weidmüller Interface GmbH & Co. KG
Klingenbergstraße 26, 32758 Detmold / Germany
Phone [phone], Fax [phone]
E-Mail [e-mail], Internet www.weidmueller.com