Document of Conformity

ManualsBrandsWeidmueller ManualsAutomation & SoftwareIE-SW-BL08-7TX-1SC

[13]

Schedule

[14] TYPE EXAMINATION CERTIFICATE No.

DEMKO 11 ATEX 150193X Rev. 7

00-IC-F0060-1 – Issue 14.0

This certificate may only be reproduced in its entirety and without any change, schedule included. Page 3 of 3

Electrical data

Model Nos.

Rated Supply Voltage and Current

IE-SW-BL05-5TX,

IE-SW-BL05T-5TX,

IE-SW-BL05-4TX-1SCS,

IE-SW-BL05T-4TX-1SCS,

IE-SW-BL05-4TX-1ST,

IE-SW-BL05T-4TX-1ST ,

IE-SW-BL05-4TX-1SC ,

IE-SW-BL05T-4TX-1SC

12/24/48 V dc, Maximum 0.25 A, Class 2, or

18-30 V ac, 50/60 Hz, Maximum 0.25 A, Class 2

IE-SW-BL08-8TX,

IE-SW-BL08T-8TX

12/24/48 V dc, Maximum 0.35 A, Class 2, or

18-30 V ac, 50/60 Hz, Maximum 0.35 A, Class 2

IE-SW-BL08-6TX-2SC,

IE-SW-BL08T-6TX-2SC,

IE-SW-BL08-6TX-2ST,

IE-SW-BL08T-6TX-2ST,

IE-SW-BL08-6TX-2SCS

IE-SW-BL08T-6TX-2SCS

12/24/48 V dc, Maximum 0.65 A, Class 2, or

18-30 V ac, 50/60 Hz, Maximum 0.65 A, Class 2

IE-SW-BL08-7TX-1SCS,

IE-SW-BL08T-7TX-1SCS,

IE-SW-BL08-7TX-1SC,

IE-SW-BL08-7TX-1ST,

IE-SW-BL08T-7TX-1SC,

IE-SW-BL08T-7TX-1ST

12/24/48 V dc, Maximum 0.5 A, Class 2, or

18-30 V ac, 50/60 Hz, Maximum 0.5 A, Class 2

For Alternate construction

of Model IE-SW-BL08(X)-7TX-1SC, IE-SW-

BL08(X)-7TX-1ST, IE-SW-BL08(X)-6TX-2SC,

IE-SW-BL08(X)-6TX-2ST, IE-SW-BL08(X)-

7TX-1SCS, IE-SW-BL08(X)-6TX-2SCS

12/24/48 VDC, 0.3/0.15/0.08A, Class 2 or

12-48 VDC, 0.3-0.08A, Class 2 or

12 VDC, 0.3A, Class 2 or

24 VDC, 0.15A, Class 2 or

48 VDC, 0.08A, Class 2 or

12-48 VDC, 0.3A max., Class 2

Routine tests:

No routine tests were considered necessary.

[16] Descriptive Documents

The scheduled drawings are listed in the report no. provided under item no. [ 8 ] on page 1 of this Type Examination Certificate.

[17] Special Conditions of Use:

• Devices are to be installed in an ATEX certified IP54 enclosure accessible only with use of a tool and used in an area of not more

than pollution degree 2 as defined by EN 60664-1.

• Provisions shall be made to provide the transient protection device to be set at a level not exceeding 140% of the peak rated voltage.

[18] Essential Health and Safety Requirements

The Essential Health and Safety Requirements (EHSRs) covered by the standards listed at item 9.

Additional information

The trademark will be used as the company identifier on the marking label.