User Documentation

4 5 6 V1.0 / 2020-10-29
8. Power Input Wiring
The PoE Injector supports a single power supply input via the 4-pin terminal located on top
side of the device. For each power input V+ and V- there are 2 internally connected pins
available. Refer to illustration below for correct wiring.
Warning / Avertissement
 Take into consideration the following guidelines before wiring the device
o Tenez compte des directrices suivantes avant de câbler l’appareil.
 Terminal block is mating with Plug and suitable for 12-24AWG (15A).
Torque value 4.5 lb-in.
o Le bornier est compatible avec les connecteurs et convient pour 12-
24AWG (15A). Valeur de couple 4,5 lb-in.
 The temperature rating of the input connection cable should higher than
105°C.
o La température de service nominale du câble d’entrée doit être
supérieure à 105 °C.
 Supplied by SELV source evaluated by UL 61010-1 or 61010-2-201
power supply only.
o Fourni par la source SELV évaluée uniquement par l'alimentation UL
61010-1 or 61010-2-201.
9. Communication Connections
The PoE Injector is equipped with the following Ethernet interfaces:
2 x 10/100/1000 Base-T(X) ports
2 x 10/100/1000 Base-T(X) PoE ports (P.S.E)
Both port groups (Eth 1 and Eth 2) are working completely independent from each other.
By design the device behaves as being 2 x 1-Port-PoE-Injectors.
Please only use cables suitable for the respective type of communication and ensure that
signals are protected from possible interference.
9.1 10/100/1000Base T(X) PoE Ports (P.S.E.)
In case of active PoE sourcing the Injector uses the pinout of “Alternative A, MDI-X
mode” of 802.3af/802.3at standards. Please see the details in the following tables.
For pin assignments for different types of cables, please refer to the following tables.
Pinout for 10/100Base-T(X)
RJ-45 Input (Data Only) RJ-45 Output (Data and PoE Power)
Pin
No.
Symbol Description Symbol Description
1 RX+ Data Receive RX+ (Vdc+) Data Receive and Feeding power (+)
2 RX- Data Receive RX- (Vdc+) Data Receive and Feeding power (+)
3 TX+ Data Transmit TX+ (Vdc-) Data Transmit and Feeding power (-)
4 NC Not connected NC Not connected
5 NC Not connected NC Not connected
6 TX- Data Transmit TX- (Vdc-) Data Transmit and Feeding power (-)
7 NC Not connected NC Not connected
8 NC Not connected NC Not connected
Pinout for 100Base-T
RJ-45 Input (Data Only) RJ-45 Output (Data and PoE Power)
Pin
No.
Symbol Description Symbol Description
1 BI_DA+ Data BI_DA+ BI_DA+ (Vdc+) Data BI_DA+ and Feeding power (+)
2 BI_DA- Date BI_DA- BI_DA- (Vdc+) Date BI_DA- and Feeding power (+)
3 BI_DB+ Data BI_DB+ BI_DB+ (Vdc-) Data BI_DB+ and Feeding power (-)
4 BI_DC+ Data BI_DC+ BI_DC+ Data BI_DC+
5 BI_DC- Data BI_DC- BI_DC- Data BI_DC-
6 BI_DB- Data BI_DB- BI_DB- (Vdc-) Data BI_DB- and Feeding power (-)
7 BI_DD+ Data BI_DD+ BI_DD+ Data BI_DD+
8 BI_DD- Data BI_DD- BI_DD- Data BI_DD-
10. LED Indicators
The front panel of the Ethernet PoE Injector contains following LED indicators:
LED Color Status Description
PWR Green
On Power is being supplied to power input.
Off Power is not being supplied.
PoE active Blue
On PoE injection is active.
Off No PoE device connected.
11. Specifications
Technology
Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX
IEEE 802.3ab for 1000Base-T
IEEE 802.3af/at for Power over Ethernet
Interfaces
RJ45 Ports
10/100/1000BaseT(X), auto negotiation, Full-/half-duplex
mode, MDI-X
LED Indicators PWR (Power), PoE active (PoE activity/detection)
Power
Input Voltage 12/24/48 V DC (12 - 57 V DC), 1 single input
(no redundancy)
Input Current (max.) 3.12 A @ 12 VDC
2.81 A @ 24 VDC
1.30 A @ 48 VDC
Connection
One removable 4-pin terminal block, Wiring cable 12-
24AWG
Overload Current Protection
Present
Reverse Polarity Protection Present
PoE
Total power budget 30 W @ 12-23 V DC; 60 W @ 24-57 V DC
PoE Pinout Mode A: Pin 1, 2 (V+); Pin 3, 6 (V-); Alternative A; MDI-X
Physical Characteristics
Housing IP30 protection, metal
Dimension (W x H x D) 41 x 95 x 70 mm (1.61 x 2.75 x 3.74 inch)
Weight 370 g
Installation DIN-rail
Environmental conditions
Operating Temperature -40 to 75°C (-40 to 167°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Operating Altitude Up to 2000 m
Regulatory Approvals
Safety UL 61010-1, UL 61010-2-201
EMC
EN 55032, EN 55024, FCC Part 15 Subpart B Class A,
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV,
IEC 61000-4-3 RS: 80 MHz to 1 Ghz: 3 V/m,
IEC 61000-4-4 EFT: Power: 0.5 kV; Signal: 0.5 kV,
IEC 61000-4-5 Surge: Power: 0.5kV; Signal: 1 kV,
IEC 61000-4-6 CS: 3 Vrms
Shock IEC 60068-2-27
Free Fall IEC 60068-2-31
Vibration IEC 60068-2-6
MTBF
Time 3.165.390 hrs
Database Telcordia SR332
Warranty
Time Period 5 years
Contact Information
Weidmüller Interface GmbH & Co. KG
Klingenbergstraße 26, 32758 Detmold / Germany
Phone [phone], Fax [phone]
E-Mail [e-mail], Internet www.weidmueller.com