User Documentation

ManualsBrandsWeidmueller ManualsAnalogue Signal ConditioningACT20P-PRO DCDC II-P

3 / 5

SPEC

custom

specic

SPEC

custom

specic

IN.LO OU.LOIN.HI OU.HI

-/+300 -/+10299 10.0300 10.0

9999

HZCURRCURR YESACTI

-/+200 -/+5298 9.99299 9.99

9998

KHZVOLTVOLT

NOPASV

-/+150 10-0

-/+100 5-0-299 -9.99-298 -9.99

0001

-/+20 0-10-300 -10.0-299 -10.0

0000

-/+10 2-10

-/+5 0-5

-/+1 1-5

-/+0.5

-/+0.1

300

200

100

0-60

0-30

0-10

2-10

SPEC

custom

specic

SPEC

custom

specic

IN.LO OU.LOIN.HI OU.HI

-/+100 -/+2099.9 20100 20

-/+50 -/+1099.8 19.999.9 19.9

-/+20 20-0

-/+10 20-4-99.9 -19.9-99.8 -19.9

-/+5 10-0-100 -20-99.9 -20

-/+1 0-20

-/+0.3 4-20

0-10

100

0-50

0-20

4-20

BWOUTIN E.PASMODE

N.PAS

OK OK

OK OKOK OKOK OK

OK OKOK OK

OK OK

OK OKOK OKOK OK

OK OKOK OK

OK OK

OK OKOK OKOK OK

OK OKOK OK

OKOK

OK OK

OK OKOK OKOK OK

OK OKOK OK

OKOKOK OKOK

OK OK

O.RNGI.RNG

999999991

5.00

999899982

4.99

00010001

-4.99

000000005

-5.00

PASSPASS

LIGH

TR.LO

TR.HI

correct

password

correct

password

incorrect

password

incorrect

password

if pass-

word was

selected

if pass-

word was

selected

if OK

pressed

≥ 2 s

if no

password

was se-

lected

if no

password

was se-

lected

OKOKOK

OKOK

OKOKOK

OKOK

down

YES

TRIM

TR.RS

LED-DISPLAY

START

Flussdiagramm / Flow diagram / Diagramme de ux / Diagramma di usso / Diagrama de ujo / 流程图

Display help text

Process value

("Start")

NB The display is normally OFF in

process state!

NO.CA

➨

DEVICE NOT CALIBRATED

DP.ER

➨

CHECK DIP SETTINGS

TR.ER

➨

CHECK TRIM PARAMETERS

EE.ER

➨

CHECK CONFIGURATION

RA.ER

➨

Conguration setup PASS

(any)

➨

SET CORRECT PASSWORD

(any)

➨

SELECT INPUT TYPE

read-only CONFIGURED INPUT TYPE

I.RNG

(any)

➨

SELECT INPUT RANGE

read-only CONFIGURED INPUT TYPE

IN.LO

(any)

➨

SET INPUT RANGE LOW

IN.HI

(any)

➨

SET INPUT RANGE HIGH

OUT

(any)

➨

SELECT OUTPUT TYPE

read-only CONFIGURED OUTPUT TYPE

MODE

(ACTI)

➨

SELECT ACTIVE OUTPUT

(PASV)

➨

SELECT PASSIVE OUTPUT

O.RNG

(any)

➨

SELECT OUTPUT RANGE

read-only CONFIGURED OUTPUT RANGE

OU.LO

(any)

➨

SET OUTPUT RANGE LOW

OU.HI

(any)

➨

SET OUTPUT RANGE HIGH

Bandwidth setup BW

(any)

➨

SET BANDWIDTH

Password setup E.PAS

(any)

➨

ENABLE PASSWORD PROTECTION

N.PAS

xxxx

➨

SET NEW PASSWORD

Display light

intensity

LIGH

➨

SET DISPLAY INTENSITY

TRIM functionality TRIM

(any)

➨

ENABLE OUTPUT TRIM

TR.RS

(any)

➨

RESET TRIM SETTINGS

TR.LO

(CURR)

➨

SET TRIM LO VALUE IN [µA]

(VOLT)

➨

SET TRIM LO VALUE IN [mV]

TR.HI

(CURR)

➨

SET TRIM HI VALUE IN [µA]

(VOLT)

➨

SET TRIM HI VALUE IN [mV]

Polarity invertion

info

Scolling help text

–

passive

➨

INVERT INPUT WIRE POLARITY

inverted

➨

INVERT OUTPUT WIRE POLARITY

NOTICE

• The display is switched o󰀨 until “OK” is pressed or

held for more than 1.5 s to set the display brightness.

• If the “OK” button is pressed for more than 2 s, the

conguration program returns to the previous menu

item.

• The conguration program is terminated if the buttons

are NOT pressed for more than 2 min.

*1) Both buttons must be pressed simultaneously.

*2) The password “1001” is always accepted.

*3) Only visible if password entry is enabled. (“E.PAS” = “YES”)

*4) If “TRIM” = “NO”, storeded values “TR.LO” and “TR.HI” will

be reset to “0”.

*5) Values are entered in “µA” or “mV”, depending on the ac-

tive conguration. They are reset to “0” if the conguration

is changed.

*6) If a DIP switch conguration has been selected, the menus

are displayed as “read only”.

*7) When set to “CURR” combined with “MODE” = “PASV” only

the range 4...20 mA can be selected.

*8) CURR unit VOLT unit condition

±999

µA

0.0

+99.9

Only displayed if

“I.RNG” = “SPEC”.

The displayed val-

ue is automatically

scaled.

±100

±999

±1.00

±9.99

±1.00

±9.99

Only displayed if

“O.RNG” = “SPEC”.

The displayed val-

ue is automatically

scaled.

±10.0

±99.9

±10.0

±99.9

±100

±300

*9) The display only shows the upper range value.

*10) When set to “MODE” = “PASV” or with an inverted output

range, a scrolling text display indicates that either the two

input cables or the two output cables need to be swapped

over.

Display

DIP switch

˄ Increment value / select next item

OK Proceed to next menu or return to

previous menu, when holding button

˅ Decrement value / select previous item

*3)

*1)

*2)

*4)

*5)

*3)

*2)

*8) *8)

*8)*8) *8) *8)

*8)

*10)

*7)

*6)

*6)*6)

*6)

down

Scrolling

info

text

*9)

(10 Hz)

(10 KHz)

INPUT OUTPUT OUTPUT MODE BANDWIDTH PASSWORD

2508060000/04/08-2020