User`s manual

14
CABLE ASSEMBLY
22. Attach the Long Cable (23) to the Small “U”-
Bracket (67) with a 1/4” Nylon Locknut (2)
and a 1/4” Washer (10). Do not completely
tighten the Nylon Locknut. It should be
threaded onto the end of the Cable so only
a couple of threads are showing above the
Nylon Locknut, as shown in the inset
drawing.
Attach the Small “U”-Bracket (67) to the
Weight Tube (63) with the 5/16” x 1 3/4” Bolt
(72) and a 5/16” Nylon Locknut (3).
23. Attach the Backrest (41) to the Front Upright
(42) with two 1/4” x 2 1/2” Screws (43) and
two 1/4” Washers (10).
24. Press a 1 1/2” Square Inner Cap (32) into the
Seat Frame (36).
Insert the 1/4” x 2” Carriage Bolt (38) through
the centre hole in the Seat Plate (37). Attach
the Seat Plate to the Seat (13) with two 1/4” x
1/2” Screws (18).
Insert the 1/4” x 2” Carriage Bolt (38) into the
indicated hole in the Seat Frame (36).
Tighten a 1/4” Nylon Locknut (2) with a 1/4”
Washer (10) onto the Carriage Bolt.
Attach the other end of the Seat (13) to the
Seat Frame (36) with the 1/4” x 2” Screw (24)
and a 1/4” Washer (10).
24
22
23
23
3
42
41
10
13
10
2
18
38
37
36
32
24
72
67
2
10
63
43
SEAT ASSEMBLY
23
57
10
2
CABLE ASSEMBLY
17
15
50
20
21
57
15
23
6
66
48
7
16
23
68
16. Route the Long Cable (23) around the “V”-
Pulley (6) on the Right Arm (48). Be sure that
the Cable is in the groove of the “V”-Pulley
and that the Long Cable Trap (50) is turned
to hold the Cable in place. Tighten the 3/8” x
2 1/2” Bolt (7) and the 3/8” Nylon Locknut (not
shown).
Route the Long Cable (23) around the 3 1/2”
Pulley (15) attached to the Pulley Bracket (20).
Be sure that the Cable is in the groove of
the Pulley and that the Cable Trap (66) is
turned to hold the Cable in place. Tighten
the 3/8” Nylon Locknut (21) and the 3/8” x 2”
Bolt (not shown).
Be sure that the 5/16” x 5” Bolt (68) is tight-
ened.
17. Refer to the inset drawing. If the 3 1/2” Pulley
(15) is pre-attached to the Long “U” Bracket
(57), remove it. Wrap the Long Cable (23)
around the 3 1/2” Pulley. Attach the Pulley and
two Pulley Covers (89) to the indicated hole in
the Long “U”-Bracket (57) with a 3/8” x 2” Bolt
(12) and a 3/8” Nylon Locknut (21). Make sure
that the Pulley Covers are turned so the
wide tabs are on the indicated side.
Be sure that the Cable is in the groove of
the Pulley and that the Cable and Pulley
move smoothly.
11
23
21
12
89
Wide
Tabs
15
57