User`s manual

11. Attach the Leg Press Plate (11) to the
Adjustment Tube (10) with a 5/16” x 2 1/4”
Bolt (62), two 5/16” Washers (20), and a 5/16”
Nylon Locknut (40). Be sure that the Leg
Press Plate and Adjustment Tube are ori-
ented as shown.
Press a 1 3/4” Square Inner Cap (48) into the
Adjustment Tube (10).
12. Press two 2” Square Inner Caps (56) into the
Leg Press Arm (9).
13. Locate and open the parts bag labeled
“ARM ASSEMBLY.”
Attach the Leg Press Bumper (53) to the Front
Seat Frame (8) with the 1” Tap Screw (72).
Lubricate the 3/8” x 3 1/4” Bolt (71). Attach
the Leg Press Arm (9) to the Press Base (13)
with the Bolt and a 3/8” Nylon Locknut (42).
14. Press a 1” x 7/8” Plastic Bushing (54) onto
each welded spacer on the Press Frame (12).
Slide the Press Frame onto the Press Base
(13) so that the Plastic Bushings are aligned
with the indicated tube. Note: This will be a
tight fit. Make sure that the high pulley is
on the side shown.
Lubricate the 3/8” x 8” Bolt (52). Attach the
Press Frame (12) to the Press Base (13) with
the Bolt and a 3/8” Nylon Locknut (42).
14
11
12
13
52. Locate and open the parts bag labeled
“SEAT ASSEMBLY.”
Attach the Small Backrest (18) to the Ab
Upright (1) with two 1/4” x 2 1/2” Machine
Screws (64) and two 1/4” Washers (37).
53. Press a 1 1/2” Square Inner Cap (57) into the
Rear Seat Frame (16).
Insert a 1/4” x 2” Carriage Bolt (61) through
the centre hole in a Seat Plate (41). Attach
the Seat Plate to a Seat (17) with two 1/4” x
3/4” Screws (59).
Insert the 1/4” x 2” Carriage Bolt (61) through
the indicated hole in the Rear Seat Frame
(16). Tighten a 1/4” Nylon Locknut (44) with a
1/4” Washer (37) onto the Carriage Bolt.
Attach the other end of the Seat (17) to the
Rear Seat Frame (16) with a 1/4” Washer (37)
and a 1/4” x 2” Machine Screw (63).
54. Press a 1 1/2” Square Inner Cap (57) into the
Leg Lever (15).
Lubricate the 5/16” x 2 1/4” Bolt (62). Attach
the Leg Lever (15) to the Rear Seat Frame
(16) with the Bolt and a 5/16” Nylon Locknut
(40). Do not overtighten the Nylon
Locknut; the Leg Lever must pivot freely.
Insert the 5/16” x 2” Eyebolt (79) into the Leg
Lever (15) from the direction shown. Tighten a
5/16” Nylon Locknut (40) with a 5/16” Washer
(20) onto the Eyebolt.
55. Rest the slot in the Rear Seat Frame (16) on
the indicated post in the Ab Upright (1). Attach
the Rear Seat Frame to the Ab Upright with a
5/16” x 2 3/4” Carriage Bolt (77) and the Seat
Knob (30).
55
52
53
54
9
ARM ASSEMBLY
20
SEAT ASSEMBLY
20
40
62
Angle
10
48
11
56
42
71—Lubricate
53
72
13
54
42
12
13
9
9
8
52—Lubricate
Tube
Welded
Spacers
High
Pulley
Slot
44
63
17
16
57
41
61
59
1
18
Post
1
77
16
30
16
62—Lubricate
57
40
20
40
15
79
37
64
37
FRAME ASSEMBLY