User`s manual

1.
Locate and open the parts bags labeled
“FRAME ASSEMBLY BAG ONE” and
“FRAME ASSEMBLY BAG TWO.”
Press two 2” Square Outer Caps (58) onto the
Weight Base (14) in the indicated locations.
Press a 2” Square Inner Cap (56) into the end
of the Weight Base.
Insert four 5/16” x 2 1/2” Carriage Bolts (49)
up through the Press Base (13). Insert two
5/16” x 2 1/2” Carriage Bolts up through the
Weight Base (14).
Attach the Press Base (13) to the Weight
Base (14) with two 5/16” x 2 3/4” Bolts (55),
two 5/16” Washers (20), and two 5/16” Nylon
Locknuts (40). Do not tighten the Nylon
Locknuts yet.
2. Slide the Ab Upright (1) onto the indicated
5/16” x 2 1/2” Carriage Bolts (49) in the
Weight Base (14). Hand tighten two 5/16”
Nylon Locknuts (40) onto the Carriage Bolts.
Do not tighten the Nylon Locknuts yet.
Slide the Leg Press Upright (4) onto the indi-
cated 5/16” x 2 1/2” Carriage Bolts (49) in the
Press Base (13). Hand tighten two 5/16”
Nylon Locknuts (40) onto the Carriage Bolts.
Do not tighten the Nylon Locknuts yet.
3. Press a 2” Square Inner Cap (56) into each
end of the Top Frame (2). Press a 2” Square
Inner Cap into each side of the Butterfly
Frame (3). Press two 1” Inner Caps (95) into
the top of the Butterfly Frame.
Attach the Butterfly Frame (3) to the Top
Frame (2) with a 5/16” x 3” Bolt (92) and a
5/16” Nylon Jam Nut (91). Be sure that the
Bolt is on the side shown.
Finish attaching the Butterfly Frame (3) to the
Top Frame (2) with a 5/16” x 2 3/4” Bolt (55),
a 5/16” Washer (20), and a 5/16” Nylon
Locknut (40).
2
3
FRAME ASSEMBLY
23
ATTACHING THE AB STRAP TO THE AB PULLEY
STATION
Attach the Ab Strap (35) to the Low Cable (86) at the
ab pulley station with a Cable Clip (33).
ATTACHING AND REMOVING THE SEAT
To attach the Seat (17), set the bracket on the Rear
Seat Frame (16) onto the posts on the Ab Upright (1).
Attach the Rear Seat Frame to the Ab Upright with
the 5/16” x 2 3/4” Carriage Bolt (77) and the Seat
Knob (30).
For some exercises, the Seat (17) must be removed.
First, be sure that the chain is not attached to the leg
lever. Next, remove the Seat Knob (30) and the 5/16”
x 2 3/4” Carriage Bolt (77) from the Rear Seat Frame
(16). Lift the Rear Seat Frame off the Ab Upright (1).
ATTACHING THE LEG LEVER TO THE LOW
PULLEY STATION
To use the Leg Lever (15), the seat must be attached
to the front upright (see ATTACHING AND REMOV-
ING THE SEAT above).
Attach one end of the Chain (34) to the Low Cable
(86) with a Cable Clip (33). Attach the other end of
the Chain to the Eyebolt (79) with a Cable Clip.
ADJUSTING THE LEG PRESS PLATE
Remove the Lock Pin (73) from the Adjustment Tube
(10).
Align the holes in the Leg Press Arm (9) with the
desired set of holes in the Adjustment Tube (10). Re-
insert the Lock Pin (73) through the holes in the Leg
Press Arm and the holes in the Adjustment Tube. Be
sure that the hook on the Lock Pin is clipped in
place on the Adjustment Tube.
17
30
1
15
79
86
10
9
73
Hook
33
34
6
1
4
40
40
49
49
13
2
3
14
55
40
20
56
56
56
56
92
95
91
77
16
86
33
35
1
56
58
58
55
20
49
40
49
13
14
Before you begin this step, make sure
that you have read all of the information
on page 5. This brief introduction will
save you much more time than it takes
to read it.