User`s manual

TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. The
training system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the training system, can stretch slightly when it is first used. If there is
slack in the cables before resistance is felt, the cables should be tightened. If any slack is felt when using the
weight stack closest to the ab upright, both the High Cable (85) and the Low Cable (86) will need to be tight-
ened. If any slack is felt when using the other weight stack, the Rear Cable (87), the Press Cable (88), and the
Butterfly Cable (89) will need to be tightened.
To tighten the cables, first insert the weight pin into the mid-
dle of the weight stack. Slack can be removed from these
cables several ways:
• See drawing 1. Tighten the 1/4” Nylon Locknut (44) that
connects the end of the Press Cable (88) to the Large “U”
Bracket (84).
• See drawing 1. Remove the 3/8” Nylon Locknut (42) and
the 3/8” x 2” Bolt (50) from the Cable Trap (80), 3 1/2”
Pulley (82), and Large “U” Bracket (84). Reattach the
Pulley and Cable Trap to the lower hole in the Large “U”
Bracket. Be sure that the Cable Trap is in the proper
position and that the Cable and Pulley move smoothly.
• See drawing 2. Tighten the 1/4” Nylon Locknut (44) that
connects the end of the High Cable (85) to the Small “U”
Bracket (32).
The Rear Cable (87) can be tightened in the same
manner.
• See Drawing 3. If you feel additional slack while using the
training system, the Low Cable (86) and the Press Cable
(88) can be tightened further.
Remove the 3/8” x 2” Bolt (50) and the 3/8” Nylon
Locknut (42) from the lower 3 1/2” Pulley (82), Pulley
Covers (94) and the Pulley Plates (31). Reattach the
Pulley and Pulley Covers to a higher set of holes in the
Pulley Plates with the Bolt and Locknut. Be sure that the
Cable and Pulley move smoothly.
Do not overtighten the cables. If the cables are over-
tightened, the top weight will be lifted off the weight
stack.
If a cable tends to slip off the pulleys often, it may
have become twisted. Remove the cable and re-
install it.
If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.
84
32
32
80
82
44
44
44
88
42
87
85
82, 94
82, 94
31
42
86
88
50
2
3
1
50
4
BEFORE YOU BEGIN
ASSEMBLED
DIMENSIONS:
Height: 198 cm
Width: 163 cm
Length: 178 cm
Foot Plate
Low Pulley
Station
High Pulley Station
Lat Bar
Leg Lever
Butterfly Arms
Press Arm
Weight Stacks
Backrests
Leg Press
Plate
Ab Pulley Station
WARNING DECAL 1
WARNING
DECAL 1
WARNING DECAL 2
WARNING
DECAL 2
Thank you for selecting the versatile WEIDER
®
8630
training system. The WEIDER
®
8630 offers a selection
of weight stations designed to develop every major
muscle group of the body. Whether your goal is to tone
your body, build dramatic muscle size and strength, or
improve your cardiovascular system, the WEIDER
®
8630 will help you to achieve the specific results you
want.
For your benefit, read this manual carefully before
using the training system. If you have additional
questions, please call our Customer Service
Department Customer Service Department at
0345-089009. To help us assist you, please note the
product model number and serial number before call-
ing. The model number is WEEVSY52000. The serial
number can be found on a decal attached to the train-
ing system (see the front cover of this manual).
Before reading further, please review the drawing
below and familiarise yourself with the parts that are
labeled.
25