User`s manual

13
25. Identify the Rear Cable (87)—this is the
shortest Cable. Slide one end of the Rear
Cable onto the 5/16” x 3” Bolt (92). Thread
another 5/16” Nylon Jam Nut (91) onto the
Bolt, but do not fully tighten it. Leave
enough room between the two Jam Nuts
for the Cable to pivot.
26. See the inset drawing. Attach a 3 1/2” Pulley
(82) and a Cable Trap (80) to the upper hole
in a Large “U” Bracket (84) with a 3/8” x 2”
Bolt (50) and a 3/8” Nylon Locknut (42). Be
sure that the Cable Trap is inside the
Large “U” Bracket. Note: This may come
pre-assembled.
Route the Rear Cable (87) between the Cable
Trap (80) and the 3 1/2” Pulley (82) in the
Large “U” Bracket (84). Be sure that the
Cable is in the groove of the Pulley and
that the Cable and Pulley move smoothly.
27. Wrap the Rear Cable (87) around a 3 1/2”
Pulley (82). Attach the Pulley to the Top
Frame (2) with a 3/8” x 2” Bolt (50) and a 3/8”
Nylon Locknut (42). The Cable must be
routed from the direction shown.
28. Attach the Rear Cable (87) to a Small “U”
Bracket (32) with a 1/4” Nylon Locknut (44)
and a 1/4” Washer (37). Do not completely
tighten the Nylon Locknut. It should be
threaded onto the end of the Cable only a
couple of turns, as shown in the inset
drawing.
Attach the Small “U” Bracket (32) to the indi-
cated Weight Tube (25) with a 5/16” x 1 3/4”
Bolt (68) and a 5/16” Nylon Locknut (40).
28
25
26
27
CABLE ASSEMBLY
16
36. Route the Press Cable (88) over the indicated
3 1/2” Pulley (82) attached to the Press
Frame (12). Be sure that the Cable Trap
(80) is turned to hold the Cable in place
and that the Cable is between the Pulley
and the crossbar on the Press Frame.
Tighten the 3/8” Nylon Locknut (42) and the
3/8” x 3 1/2” Bolt (not shown).
37. Wrap the Press Cable (88) around a V-Pulley
(98). Attach the V-Pulley to the lower bracket
on the Leg Press Upright (4) with a 3/8” x 2
1/4” Bolt (83) and a 3/8” Nylon Jam Nut (43).
38. Wrap the Press Cable (88) around a 3 1/2”
Pulley (82). Attach the Pulley and a Cable
Trap (80) to the Leg Press Arm (9) with the
3/8” x 5” Bolt (74).
Slide another 3 1/2” Pulley (82) with a Cable
Trap (80) onto the 3/8” x 5” Bolt (74). Hand
tighten a 3/8” Nylon Locknut (42) onto the
Bolt. Do not tighten the Nylon Locknut
until step 40.
39. Wrap the Press Cable (88) around a 3 1/2”
Pulley (82). Attach the 3 1/2” Pulley and a set
of Pulley Covers (94) to the bracket on the
Front Seat Frame (8) with a 3/8” x 2 1/2” Bolt
(65) and a 3/8” Nylon Locknut (42). Be sure
that the large tab on the Pulley Covers is
in the position shown and that the Cable
and Pulley move smoothly.
39
36
37
38
CABLE ASSEMBLY
92
91
87
87
80
42
84
50
82
82
82
50
42
37
44
25
32
68
2
87
84
87
87
40
65
82
88
42
8
88
42
12
Crossbar
82
80
42
82
82
9
80
80
74
88
88
98
4
83
43
87
44
32
37
94—Large
tabs should
be here