User`s manual

17
40. Note: The 3 1/2” Pulley (82) used in this
step was attached in step 38. It is shown
removed for easier part identification.
Route the Press Cable (88) around the 3 1/2”
Pulley (82). Be sure that the Cable Trap (80)
is turned to hold the Cable in place and
that the Cable is routed as shown. Tighten
the 3/8” x 5” Bolt (74) and the 3/8” Nylon
Locknut (42).
41. Slide a 5/16” Washer (20) onto a 5/16” x 2 3/4”
Bolt (55). Insert the Bolt into the Front Seat
Frame (8). Slide another 5/16” Washer onto
the Bolt. Fully tighten a 5/16” Nylon Jam Nut
(91) onto the Bolt. Slide the end of the Press
Cable (88) onto the Bolt. Thread another
5/16” Nylon Jam Nut onto the Bolt, but do
not fully tighten it. Leave enough room
between the two Jam Nuts for the Cable to
pivot.
42. Identify the High Cable (85)—this is the
shortest remaining cable. Wrap the High
Cable around a 3 1/2” Pulley (82). Attach the
Pulley to the Top Frame (2) with a 3/8” x 3 1/2”
Bolt (66), a 3/8” Washer (38), and a 3/8”
Nylon Jam Nut (43). Be sure that the end of
the Cable with the ball is on the indicated
side of the Pulley and that the Cable is
between the Pulley and the post.
43. Wrap the High Cable (85) around a 3 1/2”
Pulley (82). Attach the Pulley and a Cable
Trap (80) to the Top Frame (2) with a 3/8” x
3 1/2” Bolt (66), a 3/8” Washer (38), and a
3/8” Nylon Jam Nut (43). Be sure that the
Cable Trap is positioned to hold the Cable
in place.
43
41
42
CABLE ASSEMBLY
12
21. Wrap the Butterfly Cable (89) around a 3 1/2”
Pulley (82) as shown. Attach the Pulley and a
Cable Trap (80) to the bracket on the Leg
Press Upright (4) with a 3/8” x 2” Bolt (50)
and a 3/8” Nylon Locknut (42). The Cable
Trap must be oriented as shown and be
positioned to hold the Cable in the groove
of the Pulley.
22. Route the Butterfly Cable (89) around a 3 1/2”
Pulley (82). Using a 3/8” x 2” Bolt (50) and a
3/8” Nylon Locknut (42), attach the Pulley and
a set of Pulley Covers (94) to the top of the
Pulley Plates (31). Note: Be sure that the
small tab on the Pulley Covers is facing up
and that the end of the Pulley Plates with
three holes is down.
23. Wrap the Butterfly Cable (89) around a 3 1/2”
Pulley (82) as shown. Attach the Pulley and a
Cable Trap (80) to the other side of the bracket
on the Leg Press Upright (4) with a 3/8” x 2”
Bolt (50) and a 3/8” Nylon Locknut (42). The
Cable Trap must be oriented as shown and
be positioned to hold the Cable in the
groove of the Pulley.
24. Note: The Left Butterfly Arm (6) is shown
removed for easier part identification.
Insert a 5/16” x 1” Bolt (51) through the brack-
et on the Left Fly Arm. Fully tighten a 5/16”
Nylon Jam Nut (91) onto the Bolt.
Slide the free end of the Butterfly Cable (89)
onto the 5/16” x 1” Bolt (51). Thread another
5/16” Nylon Jam Nut (91) onto the Bolt, but
do not fully tighten it. Leave enough room
between the two Jam Nuts for the Cable to
pivot.
24
21
22
23
CABLE ASSEMBLY
6
End with
three hole
should be
down
31
4
89
82
50
80
4
42
89
82
50
80
89
50
51
91
89
43
38
2
66
82
85
Post
85
80
38
66
2
82
43
40
9
82
42
80
88
91
8
88
20
20
55
74
42
94—Small tabs
should be up
42
82