User`s manual

17
36. Slide a 5/16” Flat Washer (8) onto a 5/16” x
2 3/4” Bolt (11). Insert the Bolt through the indi-
cated hole in the Pivot Arm (101). The Bolt
must be inserted from the side shown.
Fully tighten a 5/16” Nylon Jam Nut (93) onto
the Bolt.
Wrap the Military Press Cable (72) around a
3 1/2” Pulley (15). Attach the Pulley and a
Cable Trap (66) to the Pivot Arm (101) with
the 3/8” x 3 3/4” Bolt (88), a 3/8” Flat Washer
(9), and a 3/8” Nylon Locknut (21). Be sure
that the Pulley is on the side shown and
that the Cable Trap is positioned to hold
the Cable in place.
37. See inset drawing A. Attach a 3 1/2” Pulley
(15) and a Cable Trap (66) to the upper hole
in a Long “U”-Bracket (57) with a 3/8” x 2”
Bolt (12) and a 3/8” Nylon Locknut (21). Be
sure that the Cable Trap is inside the Long
“U”-Bracket. (Note: This may come pre-
assembled.)
Route the Military Press Cable (72) through
the Long “U”-Bracket (57) and the 3 1/2”
Pulley (15). Be sure that the Cable is in the
groove of the Pulley and that the Cable
and Pulley move smoothly.
See inset drawing B. Slide the end of the
Military Press Cable (72) onto the end of the
5/16” x 2 3/4 Bolt (11). Thread another 5/16”
Nylon Jam Nut (93) onto the Bolt. Do not
fully tighten the second Jam Nut. There
must be room between the two Jam Nuts
for the end of the Cable to pivot.
37
CABLE ASSEMBLY
12
20. Wrap the High Cable (58) around a “V”-Pulley
(50). Attach the “V”-Pulley and a Long Cable
Trap (31) to the indicated bracket on the Front
Upright (42) with a 3/8” x 2 1/2” Bolt (86) and
a 3/8” Nylon Locknut (21). Be sure that the
Long Cable Trap is positioned to hold the
Cable in place.
21. Route the High Cable (58) around the “V”-
Pulley (50) on the Left Arm (47). Be sure that
the Cable is in the groove of the Pulley
and that the Long Cable Trap (31) is posi-
tioned to hold the Cable in place. Tighten
the 3/8” x 2 1/2” Bolt (86) and the 3/8” Nylon
Locknut (not shown).
22. Route the High Cable (58) around the “V”-
Pulley (50) on the Right Arm (48). Be sure
that the Cable is in the groove of the “V”-
Pulley and that the Long Cable Trap (31) is
turned to hold the Cable in place. Tighten
the 3/8” x 2 1/2” Bolt (86) and the 3/8” Nylon
Locknut (not shown).
23. Attach the Pulley Bracket (20) to the Top
Frame (55) with the 5/16” x 5” Bolt (68) and a
5/16” Nylon Locknut (3). Do not overtighten
the Nylon Locknut; the Pulley Bracket
must be able to move freely.
See the inset drawing. Route the High Cable
(58) around the 3 1/2” Pulley (15) attached to
the Pulley Bracket (20). Tighten the 3/8” x 2”
Bolt (12) and a 3/8” Nylon Locknut (not
shown). Be sure that the Cable is in the
groove of the Pulley and that the Cable
Trap (66) is turned to hold the Cable in
place.
23
20
86
86
31
31
50
50
21
58
58
21
22
CABLE ASSEMBLY
42
47
86
31
50
58
20
68
3
55
48
72
15
21
57
A
B
12
15
66
57
93
72
Bracket
58
15
66
12
36
88
11
72
21
66
101
15
9
93
8
11