775 Glenn Ave, Wheeling, IL 60090 WBSC457LC SOD CUTTER Operator's manual (Original instruction) DO NOT operates this equipment until you have read and understood all enclosed Operator’s Manual.
Content 1 Pre-operation note------------------------------------------------------------------------1 2 Safety precautions------------------------------------------------------------------------2 3 Assembly-------------------------------------------------------------------------------------8 3.1 Unpacking instructions----------------------------------------------------------8 3.
Following security identity is to remind you always pay attention to safety during operation: Danger: Show immediate serious results of injury or death. Warning: Show unsafe actions or conditions may cause serious injury, death or damage to major equipment. Caution: Show unsafe action or conditions may cause injury or property damage. Any modification unauthorized by manufacturer is prohibited.
objects to be avoided during work, such as sprinkler heads, water valves, buried cables, or clothes line anchors etc. Do not use the machine if it has been modified or improperly maintained. All jobsites are different. Please ensure that when using the WEIBANG sod cutter, all local bylaws and codes are followed. All operators and mechanics of this machine should be trained in general machine use and safety.
c. Know and mark the location of any and all buried utility lines or sprinkler systems. If in doubt, always check with your local utilities provider for survey information and assistance. d. Check for ventilation in area. Do not operate the sod cutter or run the engine in unventilated areas. Engine exhaust contains carbon monoxide, a deadly gas that is odorless, colorless, and tasteless. ALWAYS OPERATE CHIPPER/SHREDDER OUTDOORS!! 4 Always wear proper safety clothing and equipment for the job.
●Before attempting to clear any jams in the unit, inspecting or servicing any part of the machine, stop the engine and remove the sparkplug wire, and make sure that all moving parts have come to a complete stop. ●Never leave machine unattended. Shut off the engine whenever you leave the work area. ●This machine only used for cutting sod and should not be used for any other purpose. The inappropriate use of any machine can cause serious damage and/or bodily harm to the environment and operator.
4. Never leave machine unattended. Shut off the engine and shift the ignition switch to “OFF” whenever you leave the work area. 5. For engaging blade or selecting gears, reduce the throttle and pull the clutch handle slowly until the transmission is semi-engaged to avoid damaging gears. 6. Do not engage the blade until the transmission is in neutral, FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. 7.
4. Quantity Required of Each Part 5. Part Numbers 6. Part Descriptions.
FUEL TANK: PART No. L0106040Z Qty Required=1PCS SERVICE: PART No. L0106080Z Qty Required=2PCS WARNING: PART No. L0203000 Qty Required=1PCS OPERATOR: PART No.
Carefully read these instructions and this manual in its entirety, before you attempt to operate your new shredders. IMPORTANT: THIS SOD CUTTER IS DELIVERED WITHOUT OIL OR PETROL IN THE ENGINE. Your new sod cutter has been pre-assembled at the factory, with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc. necessary to complete the assembly have been attached on the machine.
II HOW TO SET UP YOUR SOD CUTTER CAUTION: Wear protective gloves during operation of setting up your sod cutter. Ｔｅｎｐｏｒａｒｙ ｂｒａｃｋｅｔ Ｎｙｌｏｎ ｓｐａｃｅｒ Ｈａｎｄｌｅ ｂａｒ Ｒｏｄ Ｇｅａｒ ｂｏｘ Ｐａｒｔｓ ｒｅｌａｔｉｏｎｓｈｉｐ Ａｓｓｅｍｂｌｅｄ 1) Remove the temporary bracket, and then install the components of handle-bar & rod, and then connect the screw end of clutch cable to the belt clutch handle according to installing drawing.
Blade controling handle Upper locking lever Throttle controlling lever Gear selecting lever Blade engaging lever Bumper Starting knob Belt-clutch lever Handle bar Lower locking lever Driving wheel Blade Crank Oil gauge 1. Bumper, Used for protecting the engine and the towing the machine. 2. Blade-controlling handle，used for controlling cutting depth and blade angle. 3. Upper locking lever, used together with blade controlling handle for setting different cutting depth. 4.
CAUTION: Do not transport or move machine while the engine or machine is running. Stop the engine and remove the sparkplug wire, and make sure that all moving parts have come to a complete stop. Prevent fuel spillage, gasoline is flammable and vapors are explosive. ● The machine is equipped with 14-inch 6PR inflatable tires with ball bearings, which make the machine can self propelled easily for short distance. Do not manually drive the machine until the gear is disengaged.
Before using the WEIBANG WBSC457LC Professional Sod cutter, please perform the following procedures for the personal and property safety of the operator and jobsite and for optimal performance. 1). Before operating the sod cutter ensure that it is structurally and mechanically safe by checking the following: a. Perform a detailed visual inspection on the machine with particular attention to the following: i. Are there any loose, worn or damaged parts? If so, DO NOT ATTEMPT TO OPERATE THE MACHINE.
WARNING: Before operating the machine, be sure to read all safety, controls and operating instructions in this Owner’s Manual and on decals located on machine. Server personal injury or property damage could result if this instruction is not followed. Before starting the machine 1. Read and understood all the sections in this manual. 2. Make sure the oil is the grade recommended by engine manufacturer. (Refer to engine operator’s manual） 3.
See sod cutter instruction manual for starting, procedure and additional safety instructions before using the machine. 7.2 OPERATION THE MACHINE TO CUTTING SOD 1. Start the engine when the gear box is in neutral. 2. Turn the throttle lever to accelerate the engine till it runs smoothly (idle speed). 3. Lift the handle bar, and then pull the blade-controlling handle back to lower the blade. 4.
9.1. Adjusting blade angle: Turn and release Adjust blade angle lower locking lever, and then turn blade controling lever to desired blade angle, then relock lower locking lever. Blade controling lever Lower locking lever Lossen 9.2. Adjusting cutting depth: Tight 1) For precise adjustment, set blade angle and keep the solt "A" in vertical direction. 2) Turn star knob to release the locating block. 3) Turn and release upper locking lever.
7.3 Notes during operation 1. Start the machine when the gear shifting lever is set in neutral. 2. To select gears successfully, slowly accelerate the throttle and meanwhile swing the selecting lever gently to engage gears completely. 3. Set the gear selecting lever in neutral before stopping the machine. 4. Soil conditions will influence cutting depth. If the cutting movement is from hard soil to soft soil or damp places, the cutting depth should be re-adjusted. 5. Do not cutting sod during U-turn.
Before any service and adjustments: 1. Make sure the blade and all moving parts have stopped completely. 2. Disconnect cable from the sparkplug and place where it cannot come in contact with plug. CAUTION ●Any modifications unauthorized by manufacturers to the machine will lead to the failure of warranty. ●Do not operate the machine until read and understand all enclosed operator’s manual.
When sod cutter is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store the sod cutter in a clean and dry place. 1. Clean the entire sod cutter (See "CLEANING" in the customer Responsibilities section of this manual) 2. Lubricate as shown in the Customer Responsibilities section of this manual. 3. Be sure that all nuts, bolts, screws and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. 4.
OTHER ● Do not store petrol from one season to another. ● Replace your petrol can if your can starts to rust. Rust and/or dirt in your petrol will cause problems. ● If possible, store your sod cutter indoors and cover it to give protection from dust and dirt. ● Cover your sod cutter with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your Chipper/shredder to rust.
Is the drive belt tension set properly? Refer to “Replacing Drive V-Belt and Pulley” for details. Does the drive belt show signs of wear and tear? Replace if necessary. Is the blade & rotor assembly in good condition? Are any blade worn down to minimum length of 3”/7.6 cm? If so, have they been replaced? Are the safety warning labels and other decals clearly identifiable and legible? If not, ensure that fresh decals will be re-applied prior to use for operator safety.
Item Suggested Lubricant Engine Refer to Owner's Every 20 hours Every 60 hours As required After each Pressure wash Storage √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ Manual for Engine Gear box Replace oil Wheels Lithium-based Grease Handle Attachment Kits General Purpose Spray Lubricant Blade Rotor General Purpose Spray Lubricant & Linkage General Purpose Spray Lubricant Zerks General Purpose Spray Lubricant Blade control group General Purpose Spray Lubricant √ 200 hours √ √ √
BY A TRAINED AND EXPERIENCED TECHNICIAN. Ensure that the work area is clean and free of debris prior to starting any maintenance or service work. Small particles may become trapped in key components that may lead to serious damage to the machine and cause severe bodily harm to the operator or technician. Use WEIBANG brand-name parts for compatibility and optimum performance. Use of any other parts prior to consulting with your local dealer will void all warranties expressed herein. 10.3.
LUBRICATION ●Assure a proper lubrication of your chipper/shredder (See "LUBRICATION CHART"). SOD CUTTER ●Always observe safety regulations when performing any maintenance or service works. TYRES ●Do not expose tires to petrol, oil, or insecticides or other chemicals, which can cause damage to rubber parts. ●Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. SHARPENING THE BLADE Bad cutting effect means the cutting blade have become dull and need re-sharpening.
until engine has been disabled. Switch off engine and then remove spark plug wire. Be sure to wear personal protective equipment. Do not let the drive belt is too loose! Adjust the relative position of cable screw tube attached to the cable bracket to improve the transmission effect, in case the drive belt is too loose when the tensional pulley is engaging. If the drive belt is still too loose when the tensional pulley is engaging, adjust engine’s position as follows: i.
local Authorized Service Centre or WEIBANG’s exclusive national distributor to complete this work or for details. ENGINE Read the Maintenance section of your engine manual. LUBRICATION Use only high quality detergent oil, which has an API service classification of SF-SJ. Select the oil's SAE viscosity grade according to your expected operating temperature. NOTE: Although multi-viscosity oils (5W30,10W30 etc.
AIR FILTER Your engine will not run properly and may be damaged by using a dirty air filter. Clean the element after every 25 hours of operation, or more often if chipper/shredder is used in very dusty or dirty conditions. See the Maintenance section of your engine manual. MUFFLER Inspect the muffler regularly and replace a corroded muffler, as it could create a fire hazard and/or cause damages. SPARKPLUG Change your sparkplug each year to make sure your engine starts more easily and runs better.
5. 6. Transmission belt excessive wore or damage Blade can not work well Belt fall off Bolt is loosen damaged or Tires wear excessively Can not shift the gear selecting lever fluently. Blade is blunt or deformed, Contact your local dealer for re-sharpen details or replacement. Check the belt and tensional state, adjust on request. Important: switch off the engine until the machine come to a completely stop. 1.
WEIBANG Warranty Statement WEIBANG GARDEN MACHINE COMPANY LIMITED guarantees all WEIBANG sod cutter to be free from any manufacturer’s defects in material and workmanship for a period of 1 year from the date of purchase. This warranty is exclusive of the engine (please consult the accompanying engine manual with your unit for details), and any normal wear and tear and/or consumable parts, such as, but not limited to, flails, spacers, clutch, clutch lining, drive belt, and throttle cable.
