ＷｅｅｅＢｏｔ Ｊｅｅｐ
To my classmates There is endless whimsy in your mind every day. Make a fan, a car, or even a robot� Nothing can limit our imagination! From now on, roll up your sleeve and create anything you want in your dream.
WeeeBot Jeep Part List 1X Left Side Panel 1X LED Panel Module 2X Screw M2*4 1X Right Side Panel 1X RGB Ultrasonic Sensor 2X Screw M2*6 4X Beam 1030-100-B 1X Line-following Sensor 4X Screw M3*25 6X 56T-plastic Gear 1X Light Sensor 2x ScrewM4*30 6X 56T-plastic Gear with Lug Boss 1X Infrared Receiver Sensor 2x Nylon Locknut M4 4X Tire 64*16 1X Sound Sensor 2x Aluminum Stud 4*6*10 2X TT Motor 3X 4P4C RJ11 Cable-20cm 4x Flange Bearing 4*8*3 1X ELF Base Board 1X 5.5-2.
Battery Instruction There are two options for WeeeBot power supply: 4 x 1.5V AA batteries (Not included in package), or 2 x 3.7V 18650 Lithium battery (Not included in package). Battery information: 1. Do not crush, or throw batteries. 2. Do not use batteries near to a heat source. not short-circuit lithium battery. 4. Always keep batteries dry. 5. Do not puncture battery with sharp object. 6. Use only the correct type and size of battery indicated. 7.
Tool Instruction Screw M4*6 Screw M2 Screw M2*6 Screw M2 Screw M4 Screw M3 Screw M2*4 Screw M3*25 PH0 Screwdriver H2.5 Screwdriver M1.
Assembly Tips Assembly Steps Number of Parts Parts Required Explain Assembly Path Install LED Panel Module Considerations Tip：Please follow the installation guide in the left side. 4X Nut M4 4X Screw M4*6 1X LED Panel Module Steps: 1. Install 4 x Screw M4*6 and 4 x Nut M4. Do not lock them. 2. Match the 4 screws with the gap on LED Panel Module. 3. Lock 4 x Screw M4*6 with nut.
Assemble WeeeBot Assemble WeeeBot Body Structure ‒ Install the front beam and side panel 2X Beam 1030-100-B 8X Screw M4*6 1X Left Side Panel 1X Right Side Panel Steps: 1. Install left side panel (The strip surface faces toward the outside), and two beam 1030-100-B (The convex surface faces toward the outside). 2. Install right side panel (The strip surface faces toward the outside).
Assemble WeeeBot Install Wheels 2X Wheel 2X Screw M2*6 Install Caster 1X Plastic Caster 1X Line-following Sensor 2X Screw M4*6
Assemble WeeeBot Install RGB Ultrasonic Sensor 1X RGB Ultrasonic Sensor 2X Screw M4*6 Install LED Panel Module Tip：Please follow the installation guide in the left side. 4X Nut M4 4X Screw M4*6 1X LED Panel Module Steps: 1. Install 4 x Screw M4*6 and 4 x Nut M4. Do not lock them. 2. Match the 4 screws with the gap on LED Panel Module. 3. Lock 4 x Screw M4*6 with nut.
Assemble WeeeBot Install Battery (Two power supply options available) Option 1: 4 x AA Battery 1X *4 AA Battery Holder 1X 18650 Battery Holder Option 2: 18650 Lithium Battery 2X *Nylon Rivets 4060 4X AA Battery (Not included in package) Steps: 1. Slide open the cover of 18650 Battery Holder. 2. Follow the installation diagram below, fix AA Battery Holder on 18650 Battery Holder with Nylon Rivet 4060. (the side with wire face up) 3.
Assemble WeeeBot Install Battery Holder (Two power supply options available) Option 1: 4 x AA Battery 6X Screw M4*6 1X Beam 1030-100-B Option 2: 18650 Lithium Battery 1X AA Battery Holder Steps: 1. Install AA battery holder as installation diagram. 2. Install Beam 1030-100-B(The convex surface faces toward the outside). Left side panel installation diagram (Right side panel is the same) 6X Screw M4*6 1X 18650 Battery Holder 1X 5.5-2.1 DC Power Cord-15cm 1X Beam 1030-100-B Steps: 1.
Assemble WeeeBot Wiring 3X 4P4C RJ11 Cable-20cm LED Panel Module RGB Ultrasonic Sensor Steps: 1. Wiring RJ11 cable on all sensors and electronic modules, take the other open end of RJ11 cable out of WeeeBot body structure. 2. After Step 9, connect the open end of RJ11 cable with ELF mainboard. Line-following Sensor Tips 1. Motor M1 wire to port M1, motor M2 wire to port M2. (Motor cable: black wire on the left, white wire on the right) 2.
Assemble WeeeBot Install ELF Mainboard Tip: Port ABCD should face toward car front. 4X Screw M4*6 1X ELF Mainboard Steps: 1. Place ELF Mainboard in position (see diagram) 2. Lock 4 x Screw M4*6 in turn. 3. Follow Step 8, wiring. First step wire TT Motor, second step wire other sensors. 4. Check wires and make it tidy. Switch on your WeeeBot and test all functions. Tips 1.
Quick Start 1. Take out IR Remote Control, insert CR2025 Button Cell (not included in package); 2. Switch on ELF mainboard, turn on the robot, use IR remote controller to control WeeeBot； 3.
Software WeeeCode Graphical Programming Software WeeeCode is a graphical programming software that developed by WEEEMAKE on the basis of Scratch 3.0. It supports graphical programming as well as Arduino IDE code. In Weeecode, you only need to drag and drop the code modules to create lots of programs and showcases. WeeeCode supports WeeeBot perfectly. Operation system：Windows/Mac More information：www.weeemake.
Additional Assembly Guide Assemble and Disassemble the Wheels 1X 56T-plastic Gear 1X 56T-plastic Gear with Lug Boss 1X Tire 64*16 Tip: Wheels are assembled in package. You can disassemble wheels per necessity. Assemble and Disassemble LED Panel Module 1X LED Panel Protective Shield 1X LED Panel Module 2X Screw M2*4 Tip: LED Panel Module is assembled in package. You can disassemble it per necessity.
Additional Assembly Guide Installation and Disassemble of ELF Mainboard Module 1X ELF Base Board 1X ELF Mainboard 1X 328P Chip Module 1X Sound Sensor 1X Light Sensor 1X Infrared Receiver Sensor 1X ***Bluetooth 2.4G Module Instruction： 1. Sensors and modules are fully installed in package as follows: Port1 ⸺ Light Sensor Port2 ⸺ Infrared Receiver Sensor Port3 ⸺ Sound Sensor MCU Port ⸺ 328P Microchip 2. ***Port is for wireless communication modules such as Bluetooth, 2.4G wireless module.
Assemble WeeeBot Jeep 1. Put screw M4*30 through Flange Bearing 4*8*3, Wheel without Lug Boss, another Flange Bearing 4*8*3, Aluminum stud 4*6*10 in order. 2. Lock Screw M4*30 with Nylon Locknut M4, make sure the wheel will run smoothly. 1. stands for parts included in WeeeBot Jeep, not included in WeeeBot. 2. WeeeBot Jeep only support 18650 Lithium Battery power supply option, package include 2 x 18650 Lithium Battery and charger.
Additional Assembly Guide Power Special Module Port Module Port Buzzer MCU Port Motor Port 1. Replaceable microchip: Support ATMEGA-328P, ATMEGA2560 chip, etc. Power Port 2. Support 10 x DC motor, or 4 x Encoder motor, or 4 x Stepper motor working. Sensor or Motor Driver Port RGB LED Sensor Port 3. Support 4 x RJ11 port and 4 Pin port, support 10 sensors (input or output) working at the same time. 4. Support 5V power port to provide stronger power for more servos. 5. Support Bluetooth, 2.
Sensors and Electronic Modules Guide Picture Description Features Specification Function Line-following Sensor is consist of two set of IR emitting LED and sensitive phototransistor. When the phototransistor detects the reflected infrared light from the IR emitting LED, it will output a digital signal, which changes from HIGH to LOW. Users can tell the different reflecting surface by this value.
Sensors and Electronic Modules Guide Picture Description Features Specification Function ATmega328P microchip is designed for ELF mainboard. Compatible with Arduino. It is an entry-level module to start coding, with features such as anti-reverse design, high performance, low power, high reliability.
FAQ Q1：When I turn on the WeeeBot, my robot has no response, why? A：It is possibly caused by: 1. Low voltage, please recharge all your batteries or replace with new batteries. 2. Batteries installed in wrong polarity (+/-); 3. Incorrect wring on battery holder or motor. Q2：When I controlled the WeeeBot to move forward, it moved backwards. How can I fix this? A：The wiring of the motor is connected reversed. Please reconnect.
FAQ Q8：When do you need to replace batteries or charge batteries? A：If the speed is set to maximum value, and your robot run slowly, or keep restarting, you must replace all batteries, or charge your rechargeable batteries. Q9：How to reset the default firmware or online firmware for ELF mainboard? A：Connect ELF mainboard to computer with USB cable, open software WeeeCode. 1. Select menu“Arduino”,click“Restore Online Filmware”. 2. Select menu“Arduino”,click“Restore Factory Filmware”.
WeeeBot Robot Kit—Warranty FCC WeeeBot FCC Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WeeeBot Robot Kit—Warranty Product SKU WeeeBot Robot Kit 160000，161000，160001，161001 Thank you for your interest in the products and services of WeeeMake. This Limited Warranty covers any defects in material or workmanship under normal use during one year since the date of purchase from authorized dealer.
Technical Support: support@weeemake.
