Owner`s manual

14
TO ATTACH DEFLECTOR
1. Unhook the 2 bungees from deck to the
mulch cover.
REVERSE OPERATION SYSTEM (ROS)
Your riding mower is equipped with a Reverse
Operation System (ROS). Any attempt by
the operator to travel in the reverse direc-
tion with the deck clutch engaged will shut
off the engine unless ignition key is placed
in the ROS "ON" position.
WARNING: Backing up with the deck
clutch engaged while mowing is strongly
discouraged. Turning the ROS "ON", to al-
low reverse operation with the deck clutch
engaged, should only be done when the
operator decides it is necessary to reposition
the machine with the attachment engaged.
Do not mow in reverse unless absolutely
necessary.
USING THE REVERSE OPERATION
SYSTEM -
Only use if you are certain no children or
other bystanders will enter the mowing
area.
1. Move motion control lever to neutral (N)
position.
2. With engine running, turn ignition key
counterclockwise to ROS "ON" position.
3. Look down and behind before and while
backing.
4. Slowly move motion control lever to
reverse (R) po si tion to start movement.
5. When use of the ROS
is no longer
needed, turn the ignition key clockwise
to engine "ON" position.
ROS "ON" Position Engine "ON" Position
(Normal Operating)
Mulch Cover
Bungee
Bungee
Mulch CoverDeflector Shield
2. Lift the mulch cover.
3. Attach the deflector to the hinge bracket.
4. Rest the mulch cover on the deflector.
5. Attach the 1 bungee from the deflector
to the deck.
Deflector
Shield
Hinge Bracket
TO TRANSPORT
When pushing or towing your riding mower,
be sure to disengage transmission by placing
shifter in neutral.
• Raise mower height adjustment to its high-
est position with mower height adjustment
lever.
• To reengage transmission, press brake
and shift out of neutral.
TO OPERATE ON HILLS
WARNING: Do not drive up or down
hills with slopes great er than 15° and do not
drive across any slope. Use the slope guide
at the back of this manual.
• Choose the slowest speed before starting
up or down hills.
• Avoid stopping or changing speed on
hills.
• If stopping is absolutely necessary, push
clutch/brake pedal quickly to brake posi-
tion and engage parking brake.
• Move motion control lever to neutral (N)
position.
• To restart movement, slowly re lease
parking brake and clutch/brake pedal.
• Make all turns slowly.
31
1 532 43 65-51 BATTERY
3 532 19 33-50 SWITCH, IGN, DLTA, P-IN, ROS
4 532 41 19-33 KEY/CHAIN
9 532 10 95-53 SWITCH, INTLK,CL, MWR, GRY
10 532 17 61-38 SWITCH, INTERLOCK, NONC,GRAY
12 532 19 27-49 SWITCH, SEAT, DP, ROS
13 532 43 72-28 HARNESS, IGN, ELECTSTART, LRV
15 532 19 25-07 SOLENOID
16 817 72 04-08 SCREW THD CUT 1/4-20 X 1/2 TY23
17 873 51 04-00 NUT KEPS HEX 1/4-20 UNC
18 532 41 66-94 CABLE BATTERY
19 532 42 12-99 CABLE STARTER
20 532 42 12-98 CABLE GROUND
21 817 06 05-12 SCREW 5/16-18 X 3/4
22 874 35 05-09 SCREW HEX M5X0.8.9MM
23 532 43 81-22 NUT M5
24 818 10 10-12 SCREW TORX #10-14 X .750
25 532 44 16-22 FUSE, 10
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
ELECTRICAL
PRODUCT NUMBER 960 26 00-01