Operator’s Manual 26" RIDING MOWER SIDE DISCHARGE ELECTRIC START PARTS AND SERVICE This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. For Parts and service, contact our authorized distributor: call 1-800-849-1297 • For replacement parts, have available the following information: a. Model Number/Manufacturer's I.D. Number b.
TABLE OF CONTENTS Warranty ................................................. 2 Safety Rules ........................................... 3 Product Specifications ............................ 6 Assembly/Pre-Operation ........................ 7 Operation .............................................. 10 Maintenance Schedule ......................... 16 Maintenance ......................................... 16 Service and Adjustments ...................... 20 Storage ............................................
DECALS RIDING MOWER - -CATALOG NO. WE261 SAFETY RULES DANGER: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. 1 WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES • Choose a low ground speed so that you will not have to stop or shift while on the slope. • Do not mow on wet grass. Tires may lose traction. • Always keep the machine in gear when going down slopes. Do not shift to neutral and coast downhill. • If machine stops while going uphill, disengage blade, shift into reverse and back down slowly. • Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blade and proceed slowly straight down the slope.
RIDING MOWER - -CATALOG NO. WE261 MOWER DECK SAFETY RULES • If fuel is spilled on clothing, change clothing immediately. • Never overfill fuel tank. Replace gas cap and tighten securely. 44 43 GENERAL SERVICE 7 45 37 39 17 46 20 36 19 9 40 39 8 17 37 6 36 5 32 31 28 35 38 4 27 • Check grass catcher components and the discharge chute frequently and replace with manufacturer’s recommended parts, when necessary. • Mower blade is sharp.
PRODUCT SPECIFICATIONS STEERING WARNING: This riding mower is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
RIDING MOWER - -CATALOG NO. WE261 STEERING ASSEMBLY/PRE-OPERATION 27 25 24 26 23 22 Your new riding mower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your riding mower all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY 4. Slide steering shaft protective foam cover over shaft.
4. Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure riding mower is in a well-ventilated area. Be sure the area in front of riding mower is clear of other people and objects. TO ROLL RIDING MOWER OFF SKID (See Operation section for location and function of controls) Flat Washer 1. Raise deck lift lever to its highest position. 2.
✓CHECKLIST RIDING MOWER - -CATALOG NO.
OPERATION CHASSIS These symbols may appear on your riding mower or in literature supplied with the product. Learn and understand their meaning.
RIDING MOWER - -CATALOG NO. WE261 CHASSIS KNOW YOUR RIDING MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR RIDING MOWER Compare the illustrations with your riding mower to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
00155 The operation of any riding mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your riding mower or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOW TO USE YOUR RIDING MOWER Motion Control Lever RIDING MOWER - -CATALOG NO.
ELECTRICAL RIDING MOWER - -CATALOG NO. WE261 TO OPERATE MOWER Your riding mower is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the deck clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills. 1. Select desired height of cut. 2.
SCHEMATIC SCH21 BATTERY FUSE-5A RED RED BLACK STARTER RELAY FUSE-40A When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. 1. Be sure freewheel control is in the transmission engaged position. 2. Sit on seat in operating position, depress clutch/brake pedal and set parking brake. 3. Place motion control lever in neutral (N) position. 4. Move deck clutch to disengaged position. 5.
TROUBLESHOOTING CHART: PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1 Faulty operator-safety presence control system. 1 Check wiring, switches and connections. If not corrected, contact a qualified service center. Poor cut - uneven cutting 1 2 3 Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, and trash under mower. Bent blade mandrel.
TROUBLESHOOTING CHART: MAINTENANCE PROBLEM -!).4%.!.#%ª 3#(%$5,% ª 2 ) $ ) . ' / 7 % 2 "%&/2% %!#( 53% %6%29 (/523 %6%29 (/523 %6%29 (/523 %6%29 (/523 %6%29 3%!3/. "%&/2% 34/2!'% CORRECTION Out of fuel. Bad spark plug. Dirty air filter. Water in fuel. 1 2 3 4 5 6 Loose or damaged wiring. Engine valves out of adjustment. 5 6 1 2 3 4 Dirty air filter. Bad spark plug. Weak or dead battery. Stale or dirty fuel. 1 2 3 4 5 6 Loose or damaged wiring.
STORAGE Immediately prepare your riding mower for storage at the end of the season or if the riding mower will not be used for 30 days or more. WARNING: Never store the riding mower with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. • Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.
ENGINE BLADE REMOVAL 1. Raise mower to highest position to allow access to blade. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth. 2. Remove blade bolt by turning counterclockwise. 3. Install new blade with stamped "THIS SIDE UP" facing deck and mandrel assembly. LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature.
REAR WHEEL 1. Block up Rear axle securely. 2. Remove dust cover, retaining ring, washer, and square key while pulling tire off. 3. Repair tire and reassemble. 4. Replace square key while putting tire back on, then replace washer and retaining ring securely in axle groove ,when pushing tire back onto shaft reach under and pull chain sprocket toward you to ease tire replacement. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Place deck clutch in “DISENGAGED” position. 4. Turn ignition key to “STOP” and remove key. 5. Make sure the blade and all moving parts have completely stopped. 6. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. RIDING MOWER 6.
