A WILSON ELECTRONICS BRAND DRIVE X Vehicle Signal Booster Kit Installation Guide Use our NEED HELP? weBoost App to guide you through the installation. See inside page for more details. support.weboost.
Download the weBoost App Download the weBoost App Use our app to guide you through setting up a weBoost cell phone signal booster in your home, business, or vehicle. Boost every network, including 5G, guide right away.
______ Index Package Contents 1 STEP 1: Mount Outside Magnetic Antenna 2 STEP 2: Mount Inside Antenna 4 STEP 3: Connect Outside Antenna Cable To Booster 5 STEP 4: Connect Inside Antenna Cable To Booster 6 STEP 5: Connect Power Supply To Booster 7 Light Patterns 8 Troubleshooting 9 Safety Guidelines 10 Specifications 11 Warranty 12
________ Package Contents Booster & Bracket Outside Antenna Inside Antenna Power Supply Optional: Adhesive disk for aluminum vehicles 1 VEHICLE SIGNAL BOOSTER DRIVE X
______ Step 1: Mount Outside Magnetic Antenna Identify a location on the top of your vehicle that is: • Near the center of the roof • At least 12 inches away from any other antennas and from any windows (including sunroofs) Cle an the surface where you will place the outside antenna. Mount the outside antenna by placing on top of vehicle. 12 in. away from windows (including sunroofs) NOTE: For aluminum roofs, use the included adhesive disk to secure outside antenna in place.
______ (STEP 1 cont.) See options below on how cable can be routed with different vehicles. NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable. Car/Sedan: Cable routed into rear side door. NOTE: When going through car wash, remember to remove your antenna. SUV/Van/Hatchback: Cable routed into top of hatchback door. Truck: Cable routed into side door.
______ Step 2: Mount Inside Antenna Identify a place to mount the in-vehicle antenna, either on the side of the seat or on the dash and mount. The location should be at least 18 inches but no more than 36 inches from where the cell phone device will be used. Use the Velcro® adhesive strip/adhesive strip provided and attach to desired location.
______ Step 3: Connect Outside Antenna Cable to Booster Connect the cable from the outside antenna to the outside antenna port on the booster. NOTE: Bracket can be used to fasten booster in a specific location if desired.
______ Step 4: Connect Inside Antenna Cable to Booster Connect the cable from the inside antenna to the inside antenna port on the booster.
______ Step 5: Connect Power Supply To Booster Connect the power supply cord to the end of the booster, labeled “Power”. NOTE: Do NOT connect the power to the signal booster until you have connected both the inside and outside antennas. Power Supply Plug the power adapter into vehicle’s 12V DC power supply. Power up your Drive X by flipping the switch on the back of the DC power adapter on.
______ Light Patterns Solid Green This indicates that your booster is functioning properly and there are no issues with installation. Blinking Red, Then Solid Green This indicates that one or more of the booster bands has reduced power due to a feedback loop condition called oscillation. This is a built in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary.
______ Troubleshooting FIXING BLINKING OR SOLID RED ISSUES This section is only applicable if the booster is red or blinking red and you are not experiencing the desired signal boost. 1 Unplug the booster’s power supply. 2 Relocate the inside and outside antenna further from each other. The objective is to increase the separation distance between them, so that they will not create this feedback condition discussed before. 3 Plug power supply back in. 4 Monitor the indicator light on your booster.
______ Antenna Kit Options The following accessories are certified by the FCC to be used with the Drive X. This radio transmitter 4726A-460021 has been approved by innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
______ Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. All inside antennas must have at least 1.5’ separation distance from all active users. RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent.
______ Specifications Drive X Product Number U471010 Model Number 460021 FCC ID: PWO460021 IC ID: 4726A-460021 Connectors SMA-Female Antenna Impedance Frequency 50 Ohms 699-716 MHz, 729-756 MHz, 777-786 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755 MHz/2110-2155 MHz Maximum Power Power output for single cell phone (Uplink) dBm 700 MHz Band 12/17 24.84 700 MHz Band 13 24.35 800 MHz Band 5 23.4 1700 MHz Band 4 21.3 1900 MHz Band 2 24.
2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product.
Notes NEED HELP? support.weboost.
Notes NEED HELP? 15 support.weboost.
Notes NEED HELP? support.weboost.
3301 East Deseret Drive, St. George, UT 1.866.294.1660 www.weboost.com support.weboost.com Copyright © 2017 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000463_Rev01_03.07.
