A WILSON ELECTRONICS BRAND DRIVE SLEEK OTR Cellular Booster For Trucks Userr Manual NEED HELP?? support.weboost.com 866.294.
______ Index Package Contents 1 STEP 1: Select Mounting Location 2 STEP 2: Assemble The Antenna 3 STEP 3: Mount The Antenna 5 STEP 4: Route Antenna Cable & Connect Booster 6 STEP 5: Route Fixed Booster Cable & Connect To Cradle 7 STEP 6: Connect System To Power 8 STEP 7: Insert Your Phone Into Cradle 9 Troubleshooting 10 Safety Guidelines 11 Specifications 12 Warranty 13
________ Package Contents Sleek Cradle 3- Way Antenna Mount Signal Booster Antenna Spring Outside Antenna Thread Lock Packets Mast Extensions & Side Exit Adapter Cable Adapter DRIVE SLEEK OTR CELL PHONE SIGNAL BOOSTER Power Supply Cradle Mount 1
______ Step 1: Select Mounting Location Select mounting location on vehicle. The antenna can be mounted in any CB mount or antenna mounting point on the vehicle. For best performance mount the antenna above the metal cab (it does not need to be above cab wind deflector). Depending on the type of truck, there may be built-in antenna mounting points. If the vehicle does not have built-in mounting points, the antenna includes a three-way mount that will work on vehicles with mirror rails.
______ Step 2: Assemble The Antenna Once you have determined the best location for the antenna and have determined if Mast Extensions are needed, insert cable through mast. cable from antenna Mast Extension OTR Antenna NOTE: Mast Extensions may not be needed depending on your mounting point. d Lock Threa Mast Extension Mast Extension OR Antenna cable NOTE: Be sure the antenna is the correct height before applying thread locker.
______ (STEP 2 cont.) NOTE: The included spring should only be used on shorter masts variations.
______ Step 3: Mount The Antenna These are some typical antenna mounting points. If the vehicle does not have built-in mounting points, a three-way mount is included that will work on vehicles with mirror rails. Upper Side Top of Mirror Mirror Arm 3-Way Mount on bird perch mast side exit adapter 3-Way Antenna Mount The cable is strong enough that it may be shut in most vehicle doors without damaging the cable.
______ Step 4: Route Antenna Cable & Connect Booster Connect the cable from the outside antenna to the booster port labeled ANTENNA by simply pressing the connector in until you hear a “click”. NOTE: Connecting cable from outside antenna to booster does not take much force. booster cable from outside antenna The included Velcro® can be used to mount the booster out-of-the way on the floor under a seat or mounted in the back of the cab.
______ Step 5: Route Fixed Booster Cable & Connect To Cradle Place booster behind seats or in back area of vehicle and route the 15ft. fixed cable to the front of the vehicle where the cradle will be located. Connect booster cable to cradle cable.
______ Step 6: Connect System To Power Connect the power to the 12V* CLA port on your vehicle and route power cable back to the booster. NOTE: We recommend routing with the same path as the cradle/booster cable (under mats and between seats). connect to booster Connect power cable to booster port labeled . NOTE: The booster will be on whenever there is power from the 12V CLA port.
______ Step 7: Insert Your Phone Into Cradle Make sure you have plenty of slack in the cable going up to the cradle (Velcro® straps included to manage excess cable). Insert your phone into cradle and watch your signal increase! cradle extends insert phone into cradle to boost signal magnetic mount attach to dash NOTE: A magnetic mount is provided which provides a versatile, safe and functional smartphone solution. IMPORTANT: The FCC requires to never use the cell phone in the cradle next to your ear.
______ Troubleshooting Solid White (LED on cradle) This indicates that your booster is functioning properly and at maximum gain. Light Off (LED on cradle) Check/secure power connections to the CLA, booster, and cradle. If light shuts off, remove from vehicle port and plug back in to reset the system. For any questions or assistance contact our weBoost Customer Support Team (1-866-294-1660).
______ Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. Any antenna used with this device must be located at least 8 inches from all persons. FCC requires to never use the cell phone in the cradle next to your ear. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters.
______ Specifications Drive Sleek Product Number U470035 Model Number 460035 FCC ID: PWO460035 IC: 4726A-460035 Frequency 698-716 MHz, 729-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Maximum Power Power output for single cell phone (Uplink) dBm 700 MHz Band 12/17 18.74 700 MHz Band 13 21.57 800 MHz Band 5 22.65 1700 MHz Band 4 25.56 1900 MHz Band 2 19.19 Power output for single cell phone (Downlink) dBm 700 MHz Band 12/17 2.1 700 MHz Band 13 2.
2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product.
3301 East Deseret Drive, St. George, UT 866.294.1660 www.weboost.com support.weboost.com Copyright © 2017 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000070_Rev01_5.23.
