Installation Guide A WILSON ELECTRONICS BRAND Home Studio / Home Studio Lite Cell Signal Booster Use our weBoost App to guide you through the installation. See inside page for more details.
Download the weBoost App Download the weBoost App Use our app to guide you through setting up a weBoost cell phone signal booster in your home, business, or vehicle. Boost every network, including 5G, positioning right away.
Index Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 STEP 1 Attach Booster Antenna to Booster & Place in Desired Location. . . . . . . . . . . . . . 2 STEP 2 Mount & Point Outside Antenna Toward Nearest Cell Tower. . . . . . . . . . . . . . . . . 2 STEP 3 Route & Connect Outside Antenna To Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 STEP 4 Power Up The Booster & Optimize The System . . . . . . .
Package Contents Home Studio/Home Studio Lite Booster & Booster Antenna 1 2-30 ft.
STEP 1 Attach Booster Antenna to Booster & Place In Desired Location Booster Antenna Attach the booster antenna to Home Studio/Home Studio Lite booster and place in room where stronger cell signal is needed. STEP 2 Mount & Point Outside Antenna Toward Nearest Cell Tower Pole mounting is preferred because it will be easier to adjust to the direction of the cell tower. Use the u-bolts to attach the antenna to a pole or exhaust pipe on roof.
(STEP 2 cont.) Point the outside antenna toward the nearest cell phone tower. To find the nearest tower, use an app such as ‘Open Signal’. This is the most critical step of the installation process because it will determine the overall performance of the booster system. Side Mounting Side mounting is a option if you can still obtain strong signal. Note: Drip holes should be pointed down towards ground.
STEP 3 Route & Connect Outside Antenna To Booster Connect the white RG-6 cable to outside antenna and route and connect cable to Home Studio/Home Studio Lite booster. All connections should be finger tightened only. STEP 4 Power Up The Booster & Optimize The System Status Lights will appear at the top Plug the power supply into wall outlet then connect into end of booster. NOTE: We strongly recommend using a power strip with surge protection.
(STEP 4 cont.) After powering up your system, check to see how your talk, text, and data rates have improved. If more is desired, you can optimize your system. After each rotation, observe signal level on your cell phone from the Inside Antenna’s projected area. Rotate the outside antenna in 1/8 turn increments, after each turn, unplug and reconnect the booster to power while observing the signal level on your cell phone from the inside antenna’s projected area.
Status Light Patterns Ban d 12 Ban d 13 GREEN This indicates that your Home Studio or Home Studio Lite booster is functioning properly and there are no issues with installation. SOLID RED Band has shutoff. This is due to a feedback loop condition called oscillation. This is a built in safety feature that causes a band to shut off to prevent harmful interference with a nearby cell tower. Refer to Troubleshooting section.
(Status Light Patterns cont.) no further adjustments are necessary. If you are not experiencing the desired boost in coverage then refer to the Troubleshooting section. BLINKING GREEN, YELLOW This indicates band has reduced gain. This indicates that one or more of the booster bands has reduced power due to overload from nearby cell tower. This is a built in safety feature to prevent harmful interference with a nearby cell tower.
Troubleshooting FIXING RED LIGHT ISSUES This involves Solid Red & Blinking Green/Red lights. ■ Tighten all cable connections (be sure to handtighten only, do NOT use tools). You may want to undo and redo the connection completely. Unplug and replug in power supply. ■ Increase the distance (horizontally or vertically) between the outside and inside antennas. Add included cable if needed. Unplug and replug in power supply.
Safety Guidelines Verify that both the outside antenna and the adapter extension cable are connected to the signal amplifier before powering up the signal amplifier. se only the power supply provided in this package. Use of an incorrect power supply may damage your U equipment. RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons. AWS Warning: The outside antenna must be installed no higher than 31 feet 9 inches above ground. This is a CONSUMER device.
(Safety Guidelines cont.) FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05, SEE BELOW: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER, PLEASE SEE BELOW: T-Mobile/Sprint/MetroPCS: https://www.t-mobile.com/support/coverage/register-a-signal-booster Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html AT&T: https://securec45.securewebsession.com/attsignalbooster.
Antenna Info The following accessories are certified by the FCC to be used with the Home Studio or Home Studio Lite Cell Signal Boosters. This radio transmitter 4726A-460065 and 4726A-460066 has been approved by innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum gain indicated.
Specifications Home Studio Cell Signal Booster 460066 Model PWO460066 FCC IC 4726A-460066 F-Female / SMA Female Connectors 75 Ohms / 50 Ohms Antenna Impedence Frequency 698-716 MHz, 728-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Power output for single cell phone (Uplink) dBm 700 MHz B12/17 23.3 700 MHz B13 22.2 Power output for single cell phone (Downlink) dBm 9.4 9.6 Noise Figure Isolation Power Requirements 800 MHz B5 23.3 1700 MHz B4 22.1 1900 MHz B2 21.
Specifications Home Studio Lite Cell Signal Booster 460065 Model PWO460065 FCC 4726A-460065 IC F-Female / SMA Female Connectors 75 Ohms / 50 Ohms Antenna Impedence Frequency 698-716 MHz, 728-756 MHz, 777-787 MHz Power output for single cell phone (Uplink) dBm 700 MHz B12/17 24.3 Power output for single cell phone (Downlink) dBm 11.7 Noise Figure Isolation Power Requirements 700 MHz B13 23.0 12.9 5.0 dB (nominal) > 90 dB 4.2V, 1.
Register your Signal Booster now! Complete the two easy steps to register your booster and receive premium customer service, special offers and more! Step 1: Take a photo of your Photoregister Code including the points ( ). Step 2: Send it in. Smartphone U.S. only Text photo to 71403 OR Email U.S./CAN weboost@photoregister.com OR Online register.weboost.com Need help? Visit photoregister.com/help or text HELP to 71403.
Notes 1-866-294-1660 15 www.weboost.com support@weboost.
2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product.
A WILSON ELECTRONICS BRAND 3301 East Deseret Drive, St. George, UT 1.866.294.1660 www.weboost.com support.weboost.com Copyright © 2020 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000477_001_03.24.
