WebEye 2.0 E10 Installation Guide (v 2.
FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Important Notice 1. WebEye is not weatherproof. Please note the environmental specifications that are included in the manual. For outdoor usage, equip a weatherproof case to protect the WebEye from water, moisture, or extreme temperature changes (higher or lower than the specifications noted below). The WebEye can be cleaned by gently wiping with a clean dry cloth. 2. Be sure to use the DC adapter that is provided by Web Gate Inc. Connecting WebEye directly to an AC current may cause damage to the WebEye.
Contents Introduction.................................................................................................................................. 5 1. What is WebEye 2.0 E10?.................................................................................................... 5 2. Supplied accessories .......................................................................................................... 6 3. Descriptions & Function.................................................................
Introduction 1. What is WebEye 2.0 E10? WebEye 2.0 E10 is a network camera server solution with an integrated Internet server, image com pression device, flash memory, and many other features. No other hardware is necessary for use. It provides real time images over networks and the Internet. Simply provide power and connect LAN cable and video cable to it. Key features Monitoring through Network 4.5 MB Flash Memory for Homepage customization Max.
2. Supplied accessories Unpack and check all the items as below. 1. E10 (1) 2. DC POWER SUPPLY (1) (FREE VOLTAGE) 3. AC POWER CORD (1) 4. CD-ROM (INCLUDING SOFTWARE & MANUAL)(1) 5. ETHERNET CABLE (1, RED) 6.
. CAMERA STAND (1) 8. PSTN CABLE (1) 9.
3.
4. Installing & Connecting 4.1. Installing WebEye 2.0 setup program Within the supplied CD-ROM DISC, there are “WebEye 2.0 E10 User’s Guide” and WebEye 2.0 setup programs for using WebEye E10 2.0. 4.2. System requirements of PC Minimal Recommended CPU Intel Pentium III 600Mhz Intel Pentium IV 1.6Ghz or above Memory (RAM) 128MB 512MB VGA 16MB 64MB Resolution 1024ⅹ768 1280ⅹ1024 HDD 5MB 1GB or higher OS Windows 98/SE/ME/2K/XP, LINUX, Windows 2000 SP4 or above / XP SP2 MAC OS 10.2.
4.3. Installig program (1) Run “WebEye 2 Setup v.1.x.x.x.exe” file of WebEye 2.0 Seup CD. (2) Select a language and click the “OK” button. (3) Press the “I Agree” button.
(4) In order to use all functions of WebEye 2.0, select “WebEye Controllers”, “WebEye Utills”, and “WESP SDK”. WebEye Controllers To istall necessary program for aeecssing WebEye 2.0 and monitoring its image. WebEye Utils To install WebEye2 Configuration Tool (Setting), WebEye2 MiniPlayer (Replaying the quick recorded file), and WebEye2 OnetimePW (Creating one time password). WESP SDK To install WESP library file that is used in WebEye 2.0.
(5) Select a folder to install and press the “Install” button. (6) Complete to install with pressing the “Close” button. Check whether all three programs are installed.
5. Connecting & Running 5.1. Connecting WebEye 2.0 E10 to Network Connect WebEye 2.0 E10 to PC directly with cross cable or connect WebEye 2.0 E10 to local Network with direct cable. 5.1.1. Connecting to PC directly (1) Connect WebEye 2.0 E10 to client’s PC with cross cable. (2) Connect the supplied AC adaptor to WebEye 2.0 E10.
5.1.2. Connecting to local Network (1) Connect WebEye 2.0 E10 to HUB with direct cable. (2) Connect the supplied AC adaptor to WebEye 2.0 E10. 1. To prevent WebEye 2.0 E10’s damage, you should connect power cable after connecting Ethernet cable. 2. Ethernet cable should be pushed and connected, If not, noise may be occurred. 3. Check the LED of WebEye 2.0 E10 after supplying power.
5.2. Changing IP address & Login After connecting WebEye 2.0 E10 to Network, its IP address should be changed according to each Network environment to access WebEye 2.0 E10 normally. (1) Run WebEye 2. ConfigStation Tool in PC. (2) Every WebEye 2.0, which is connected to local Network, is displayed in “Local Area Units”. (3) Register WebEye at “My Units”. (4) Move to “Network” tab in “Connectivity” menu. (5) Set IP Address, Subnet Mask, and DNS. (6) Press the “Apply” button after setting. 1.
5.3. Setting Network 5.3.1. When connected to Ethernet When WebEye 2.0 E10 is connected to Ethernet, set IP address and another information in “Network” tab. Setting IP address manually (1) Enter IP address. (2) Enter subnet mask. (3) Enter gateway. (4) Enter DNS. (5) Enter the “Apply” button. Setting IP address automatically (1) Check “DHCP Enable”. (2) Press the “Apply” button. 1. If checking “DHCP Enable”, WRS should be set. 2.
5.3.3.1. Setting dial out (1) Select PSTN. (2) Enter PSTN ISP phone number. (3) Enter ISP User ID and Password, then press the “Apply” button. 1. WebEye 2.0 E10 supports PPP among PSTN types. 2. User’s ID and password is supplied from each PSTN ISP. 3. For more information about login script, inquire of PSTN ISP. 4. In orde to use PSTN modem, set the related values of modem. 5. When accessing via Dial In, access ID and Password, which are set in FTP User Accounts, should be entered. 5.3.4.
(4) Use WebEye server name as group ID. (5) Press the “Apply” button. 1. WebEye 2.0 should be set at WRS in following cases. - When using DHCP in Ethernet - When using xDSL (except using static IP) In order to check after registering at WRS, refer to WebEye2 Configuration Tool or “Registered WebEye list” at WebGate’s web site. If checking “Add Public List”, WebEye 2.0 is registered at public list and it can be searched. URL address of registered WebEye list http://www.webgateinc.
5.5. Changing admin password & Registering user Administrator’s ID is fixed as “admin”, and the default admin password of WebEye 2.0 E10 is “admin”. The ID can’t be changed, but only password can be changed. (1) Press the “Change” button. (2) When the related dialogue is shown, enter old password & new password and press the “OK” button. (3) Press the “Apply” button. User account can be registered upto 4 users. Default user accounts are guest, user1, user2, and user3. (1) Check the “Use” for using account.
5.6. Viewing image via browser After setting Network and Video tabs, image of WebEye can be viewed via web browser. (1) Run web browser at PC. (2) Enter IP address of WebEye 2.0 to access. (3) If WebEye is accessed, login page will show. (4) Enter user ID and password, and clicking the “Login” button. (5) When login is normal, single viewer page will show and channel 1 will be displayed.
When accessinf WebEye 2.0 web page for the first time without installing WebEye Setup v1.2.x.x.exe file, an installation message for certifying and running image will be shown at login step. For using WebEYe 2.0 E10 normally, the control program should be installed.
Appendix 23
#1. Specification General CPU 32bit RISC Embedded Processor Flash memory 8MB Main memory 16MB OS Embedded Linux Video channel NTSC or PAL video format are supported 1Ch. internal video input (Built-in camera) 1Ch. external video in / output (D-SUB connector) Image compression Technology Wavelet, Progressive mode Resolution 720x486, 720x243, 360x243, 180x121, 90x60 (NTSC) 720x576, 720x288, 360x288, 180x144, 90x72 (PAL) Image compression rate 10:1 ~200:1 Image transfer rate 2 ~ 30 fps Max.
IP-Filtering (Secure Mode) Max. simultaneous users Max. 100 users Environment Operation temperature -5℃ ~ 45℃ Storage temperature -25℃ ~ 55℃ Operation humidity 30% ~ 80% R.H (free of condensation) Storage humidity 93% R.H below (free of condensation) Additional function & Input/Output Additional function Image quality Control (10 Levels) Periodical sending the images through E-Mail, FTP 4.
#2. How to recognize manufacturing date The manufacturing date by Webgate can be recognized by S/N(Serial Number) attached at the each product. S/N : Serial Number Management number for each Webgate product to combine twelve alphabet character and digit including model name, manufacturing year/month/week You can see serial number by looking at the bottom of product attached label and system info of Configuration Tool. Serial Number Format □ □ □ □ □ □ □ □ □ □ □ □ Year/Month Webgate No. Webgate No.
WEBGATE Inc. 6F, Hanlim Venture Town Bldg., 689-6, Geumjeong-dong, Gunpo-si, Gyeonggi-do, Korea (435-862) Tel : (82-31) 428-9300 Fax : (82-31) 428-3955 Sales@webgateinc.com www.webgateinc.
