H.264 MH1600H / MH1600M / MH3200M Digital Video Recoder We sincerely appreciate purchasing Digital Video Recorder.
Installaction & User Manual Introduction Thank you for purchasing a Webgate digital video recorder. This manual is for MH1600H, MH1600M, MH3200M. Before product installation and operation, please become thoroughly familiar with this user manual and other manuals referenced by this manual. This user manual and the software and hardware described here are protected by copyright law.
fire or theft. We take no responsibility for damage from any incident. Caution As this equipment undergone EMC registration and suitable for business purpose, distributors and users are aware of this point. FCC Compliance Statement Caution: Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment.
Installaction & User Manual 4. Do not charge the batteries provided with Remote Controller Important Notice 1. Do not place heavy objects on the top of the product. 2. This equipment is indoor use and all the communication wiring are limited to inside of the building 3. Product is for indoor use. It is not weatherproof. Use product with referring to its environmental specifications (Temperature & Humidity). To clean the product, gently wipe the outside with a clean dry cloth. 4.
Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
Installaction & User Manual Contents Introduction ............................................................................................................................... 1 KEY FEATURES .............................................................................. 11 INSTALL MANUAL.......................................................................... 14 1. FEATURE ................................................................................. 14 1.1 Supplied Accessories....................
3. MENU USE .............................................................................. 53 3.1 Menu Structure ............................................................................................................. 53 3.2 Function Menu.............................................................................................................. 53 3.3 Factory Reset ............................................................................................................... 54 4.
Installaction & User Manual 5.1.2 5.2 Playback function .................................................................................................. 66 SEARCH MODE ........................................................................................................... 67 5.2.1 Time Search .......................................................................................................... 67 5.2.2 Schedule Search ..........................................................................
6.5.4 Sensor ................................................................................................................. 113 6.5.5 Preset .................................................................................................................. 113 6.6 Recording setup ......................................................................................................... 114 6.6.1 Program setup ............................................................................................
Installaction & User Manual 7.6.9 Functional function at the bottom of monitor ......................................................... 133 8 JAVA VIEWER .......................................................................... 134 9 USER MANUAL FOR MOBILE VIEWER ................................ 135 9.1 Log-In page ................................................................................................................ 135 9.2 Monitoring page ..................................................
KEY FEATURES Monitoring Screen Supports real live video with high resolution per each channel and variable display mode. Real H.
Installaction & User Manual Supports manual & schedule recording Video loss detection Supports archiving event list (Sensor, Video loss, Motion detection, Text) Available record Max 5 seconds before triggering an event per each channel Search / Playback It supports variable and convenient functions for search & playback.
Supprots 10/100Mbps Ethernet/xDSL Multiple DVR connection Supports User friendly GUI and mouse function Supports User friendly GUI and mouse function Easy and simple firmware upgrade thru.
Installaction & User Manual Install Manual 1. Feature 1.
1.2 Description & Function 1.2.1 Front Division 1 2 3 Description DVD-Multi for Back up use for recorded data by DVD/CD media Back up Jog / shuttle Playback direction change and speed control Touch Panel To switch / select single channel with illuminating of relevant channel LED channel LED REC 4 5 6 To start and stop recording To lock the buttons on the front panel/remote controller in LOCK monitoring status ESC To exit menu or close pop-up window.
Installaction & User Manual Relay To run and pause Relay action by manual. Mon Switching monitor PTZ To use Focus / Menu / Preset / Aux during PTZ Sequence To run or stop user sequence. Multi To change DVISION in live or playback mode. ■(STOP) To stop replay in playback mode.
1.2.2 Rear 1.2.2.1 MH1600H No Input/ Output name Description 1 Power connector Socket for AC100V~AC240V power cord. 2 CH1~16 BNC input for camera connection 3 Loop out BNC output(Loop) for camera connection. 4 Monitor 1~4 BNC connection for monitor output. 5 Audio input(RCA) RCA connection for Audio input 6 Audio output Speaker output terminal. 7 Ground Ground between DVR & external device.
Installaction & User Manual 1.1.1.1. MH1600M No Input/ Output name Description 1 Power connector Socket for AC100V~AC240V power cord. 2 CH1~16 BNC input for camera connection 3 Loop out BNC output(Loop) for camera connection. 4 Monitor 1~4 BNC connection for monitor output. 5 Audio input(RCA) RCA connection for Audio input 6 Audio output Speaker output terminal. 7 Ground Ground between DVR & external device.
1.2.2.3 MH3200M No Input/ Output name Description 1 Power connector Socket for AC100V~AC240V power cord. 2 CH1~32 BNC input for camera connection 3 Monitor 1~4 BNC connection for monitor output. 4 Audio input(RCA) RCA connection for Audio input 5 Audio output Speaker output terminal. 6 Ground Ground between DVR & external device. 7 SMPS Fan Control the temperature of SMPS 8 D-Sub Audio port D-Sub port for Audio 9 Sensor IN Input for external sensor.
Installaction & User Manual 1.2.3 REMOTE CONTROLLER It is available to use all functions of DVR. If several DVR are set with unique ID numbers, they can be controlled with one remote controller. To use remote controller, it is necessary to set ID first which want use. Keep pressing ID button repeatedly (Up to Max. 16 times) and use it matching DVR & ID. No.
10 SEARCH To indicate search menu 11 CHANNEL BUTTON To select channel 12 SELECT Not use 13 +10 In case of selecting over 10 (+10 + 1) 14 MON Move the focus of monitoring 15 REC To start/stop recording 16 MENU Covert to menu screen 17 HELP To start Function menu 18 ◀/REW Move setting menu to left direction/REW 19 ▶/FWD Move setting menu to right direction/FWD 20 ▲/PAUSE Move setting menu to top direction/PAUSE 21 ▼/STOP Move setting menu to bottom direction/STOP 22 ENTER/
Installaction & User Manual 2. Installation 2.1 Installation and Connection 2.1.1 Connecting & Running 2.1.1.1 Connecting camera Connect CCTV camera to DVR with BNC cable as below. - The video type for all channels should be either NTSC or PAL, not be combined both - DVR sets video signal’s impedance (75Ω) automatically. Impedance is set as 75 Ω basically. If connecting a device to video output, impedance will be “Hi-z” status. - Video Type (NTSC/PAL) should be changed after booting DVR.
2.1.1.3 Connecting Audio Connect audio signal to DVR with using RCA cable or D-SUB as below. 2.1.1.4 Supplying Power Connect power cable as below. - When supplying power, DVR starts booting automatically. - In order to cut off power, press power switch on DVR front during 5 seconds, then select “YES” after appearing a pop-up window. - For supplying power again, push the Power button.
Installaction & User Manual 2.2 Running OSD menu 2.2.1 OSD menu configuration Press [MENU] in keypad of front or Click in [Main Menu] in Function menu to open configuration menu as below Main Menu Sub Menu Configuration (1) Main Menu : The selected tab is show in bright color and the related sub-menu will be shown left- below the tab. To move to the previous/next tab, use the [◀/▶] arrow buttons. To move to a sub-menu press the [Enter] key or click the mouse button when you use mouse.
2.2.1.1 Dialogue box to edit a word Dialogue box to edit a word is image shown as below; It is available to input both word and number. Keep pressing [▲/▼], [◀/▶] arrow button until the word is looking for and press [Enter] or click the mouse. In case of deleting input word press [], spacing words press [] button. To exit from dialogue box, press [Enter] or click [Enter] button by mouse after finishing word input. 2.2.2 Setting remote controller 2.2.2.
Installaction & User Manual 2.2.2.2 Setting ID If several DVRs are with unique ID numbers, they can be controlled with one remote controller. To select a specific DVR, keep pressing the ID button of remote controller until a buzzer sounds during 2 seconds. 2.2.2.3 Operable range of remote controller 2.2.2.4 Loading the batteries into the remote controller Remote controller required two AAA-type batteries. Please, refer the following installation step. 1. Remove the batter cover. 2.
2.2.3 Installation examples 2.2.3.1 Basic configuration Connect camera and monitor and Audio. 2.2.3.2 Advanced configuration Connect camera, monitor, audio, sensor, realy etc..
Installaction & User Manual 2.2.3.3 External storage & back up configuration Use USB for back up. 2.2.3.
2.2.4 Basic Setting 2.2.4.1 Viewing Image When power is on, eDVR starts automatically and displayed in basic 16ch-split screen after booting. If user password is set, a prompt for entering the password will be appeared. Factory default is reserved as not responding keypad on DVR front (It is not from factory default) 2.2.4.2 Setting Date & Time - Press [MENU] button and select “System” when OSD menu is appeared. - Select “Date/Time “and press [Enter] button.
Installaction & User Manual Time Zone Use the left or right arrow key on the front or the mouse wheel to select your time zone. Each press of the arrow keys changes the time zone. (To go to the previous menu, press the [ESC] button on the front or right-click. This is the same for all OSD menus.) Daylight saving This menu is linked with “time zone” setting.
DATE FORMAT (1) Select “Date Format” using [◀/▶] or [▲/▼] arrow button and press [Enter] button. Select a value using [◀/▶] arrow button from YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY. (2) Press [ESC] after finishing value setting. TIME (1) Select “Time” using [◀/▶] or [▲/▼] arrow button and press [Enter] button. (2) Select Date, Time using [◀/▶] arrow button and set value using [▲/▼] arrow button. (3) Press [ESC] after finishing value setting..
Installaction & User Manual 2.2.4.3 Record Setting Select “Record” pressing menu button in front. Manual Setting Manual record can be configurator in “Program” of record menu and Manual / Event record is available to Start/Stop with pressing [REC] button on front panel.
Schedule Setting Set the recording schedule by each channel that user want record in “Program” of record menu. Set recording mode as “Schedule & Event” and set by date/ time. Program Setting Set resolution, frame rate, quality by each channel that user want record in “Program” of record menu (See details in Record menu) If recording setting is finished correctly, “REC LED” in front is flickering. In addition, it is marked [SCHEDULE] indicating that all channels are recording.
Installaction & User Manual 2.3 2.3.1 Connecting and configuring DIO ports Wire Handlin When connecting a wire to a terminal block, follow the instruction below. Not the different types of wire that can be used. - Standard wire: Pie off the wiring cover 8~10mm and solder it. Wire gage should AWG 22~26. - Sold wire : Peel off the wiring cover 8~10mm and solder it. Wire gage should be AWG 20~26. 2.3.
2.3.3 Connecting and configuring sensor 2.3.3.1 Specification In order to run sensor input DVR normally, the following conditions are required. Spec Input Ch. 16EA Transistor input Input type N.C, N.O supprt Supported sensor Dry contact sensor Way of connecting Connecting the trimmed wire to terminal block Available input Minimum 500ms Performance pulse range Output current Typical DC 12mA Connecting sensor input Connect S1 ~ S16 with referring the following image.
Installaction & User Manual Setting Sensor (1) Press [Menu] button and select “Event” when OSD menu is appeared. (2) Move to sub menu pressing [Enter] or using [▼] button and select [Enter]. All Sensor It is used when setting for all sensors and set off, or Normal Open (N.O.) / Normal Close (N.C.) type. (1) Select All and set type. Each sensor It is used when setting for each sensor and set selecting each sensor. (1) Select sensor and press [Enter] button.
2.3.3.2 Connecting relay and setting Specification In order to run relay output of DVR normally, the following conditions are required. SPEC Performance Output Ch. 2EA relay outputs Output type Dry contact Connecting type Connect the trimmed wire to terminal block DC 30V 1A AC 125V 0.5A Connecting relay out Connect R1 ~ R4 with referring to the following images, it shows to connect a warning light.
Installaction & User Manual Relay setting It is available to run relay selecting from sensor, motion detection, Text, Video Loss which is normal event source and Disk error, Disk full, Fan error, authentication fail, WRS registration fail, Mirroring fail, abnormal Recording stop which is system event source. Also, user can set working condition by schedule. In case of using control center thru. network, relay could be run from remotely. 2.3.3.
Serial communication port diagram COM1 connection diagram (RS-232 – D-Sub) COM2/COM3 diagram (RS-485)
Installaction & User Manual Available PTZ is as below Model Manufacturer Keyboard KBD300A, WGI SPD1800/2600 Webgate WKC-100 keyboard Webgate PELCO(P), PELCO(D) Pelco BOSCH Auto Dome, TC8560X-4 Bosch Sony EVI-D3x Sony VT VPT-4x VT AD Speed Dome AD SungJin SJ372R1 Sungjin Samsung SCC641 Samsung Electric Panasonic WV-CS850 Panasonic SDZ160/330, Samsung SPD, Samsung Techwin Keyboard SCC3000A, Samsung SRX-100B LG GAC-PT2 LG Merit-Lilin Fast Dome Merit Elmo PTC200C Elmo Canon VC-C4
Hunt Hunt ORX-1000 Sysmenia Fine CRR-1600 LiveEye Tokina Tokina Kodicom KRE Kodicom Nuvico Nuvico Serial Setting You can set up at ‘serial’ menu under Device menu. From serial setting, you can set protocol, port, baud rate, parity bit, stop bit and data bit. After completed serial setting, select desired channel from camera menu, and setting up PTZ Home, PTZ Idle Time, PTZ Port, and PTZ address.
Installaction & User Manual 2.3.3.4 Connection to external device via Serial port Text input device connection (ATM / POS / Access Control) Using COM1/RS232, TEXT DATA can be recorded with synchronizing POS/ATM.. Like above picture, connect COM1/RS232 (9pin D-Sub) in Device menu and configure Serial and Text Serial (COM1) Setup (1) OSD Select “Device” in OSD menu and move to sub menu.
Since external device cannot be recognized, before installing, please, ask to the shop. 2.3.3.5 USB Device Connection USB port is for the video copy of small data or for USB mouse. Its recommended specification is same as below. USB Spec. Device Voltage/electric current Ver 2.0 USB Memory Stick, Max. 200mA per DC 5V / Port It should be formatted by FAT32.
Installaction & User Manual In case of normal connection, if executing Copy menu, disk will be recognized same as below and Set copy range Select Drive Execute Copy [CD/DVD Copy] [RE4 Copy] Select the channel to copy. Standard setting is selecting all channels.
[AVI Copy] A USB Flash memory which should install additional program on Windows OS, cannot be recognized. 2.3.3.6 Video In/Out connection Video Input/Output is Loop through and check the connectivity automatically and set end resistance. For instance, if connected by Video input, end resistance is configured by75Ω and if Video in/output is same, it will be Hi-z mode.
Installaction & User Manual 2.3.3.7 Audio In/Out connection There are 4 RCA Audio Input and and 12 D-sub Audio input and 1 RCA output. 2.3.4 HDD ※ Please, ask to distributor or manufacturer for available HDD list. 2.3.4.1 HDD registration and format After mounting HDD and booting system, “Disk Manager” will execute automatically. If not, please, check the connectivity of HDD (1) Press [Enter] button in “Disk Manager” (2) Using [▲/▼] Key select new HDD(Displayed [No] on Enabled item) and press [Enter].
2.3.4.2 HDD Replacement (1) Turn off the DVR and take off the HDD that has a problem and replace it with new HDD. (2) Turn On the DVR and go to “Disk Manager” menu and select the removed HDD which has a problem, and press “Enter” Key. (3) “Removed disk will be Confirmed” message will be pop-up and select “Yes” to delete it from the list. (4) Select the new HDD from the list and press “Enter” key.
Installaction & User Manual (1) Cut power (2) Connect Ethernet cable to DVR and Hub. (3) Input Power.. To protect DVR damage, after connecting Ethernet cable, input Power. Please, check Ethernet cable connection firmly. Input power on DVR and check their connectivity. 2.3.5.2 Network configuration Ethernet Set type as Ethernet and input IP, Netmask, Gateway, DNS. The way to input is using directional key or mouse wheel. PPPoE Set type xDSL, and move to xDSL menu.
WRS After changing interval over 1 min, register WRS address and product and input Group ID.
Installaction & User Manual 2.3.6 External device connection DVR has external Storage Device Interface and 1ea of eSATA port. Using eSATA port, user can expand Storage capacity up to 8TB. Since some of eSATA device can not be compatible with DVR, before the usage, please, contact the seller and check its compatibility in advance. 2.3.6.1 eSATA Device Connection In case of external eSATA supporting FireWire, using eSATA port on the rear part.
2.3.7 NVS04 connection 2.3.7.1 Connecting with DVR (1) Connect to DVR as shown in the picture below using Gigabit Ethernet Cable. (2) Connect DVR Port of NVS04R and Storage Port of DVR directly.. 1) The network cable connected to DVR should be Gigabit Ethernet Cable (Category-6). If not, it is not connected to DVR. 2.3.7.2 Set ID Configuration Set ID using Rotary Switch located on the back. This ID is used as IP Address of NVS04R and the form of IP address is 10.10.20.XXX.
Installaction & User Manual Set the ID using driver. The value for the first digit of switch should match with values of 100x on the rare panel while the second digit of switch should match with value of 10x and the third digit of switch should match with 1x on the rare panel 2.3.7.3 Power connection and operation (1) Connect power as below. (2) As soon as power is connected, the device starts booting. 1) It takes around 1 minute to connect NVS04R and DVR after connecting power.
User Manual 3. Menu Use 3.1 Menu Structure The menu structure will be shown like below image, and each menu setting method descriped from chapter 4 to chapter 6. 3.2 Function Menu To run Function menu, please, click the right button of mouse in live monitoring or playback status or push “Func” button on the front panel. The Function menu can be controlled by mouse. Each function can be executed by clicking right button of mouse and click desired icon.
Installaction & User Manual Function of Playback 3.3 Factory Reset In order to reset value to factory value, go to System Setting->System->Setting, and once press Factory Reset then the warning message will be appear, click “Yes” to reset the DVR value to factory. Default Value from Factory System Time Zone UTC 00:00 Dublin Daylight Saving Off NTP Function Sync With Off NTP NTP Mode Date NTP / Client Server Public Loc. Time NTP Local 0.0.0.
User Setup Utility Right O DVR Alias DVR0 Language English DVR Keyboard ID 1 Remote Controller All ID Network Network Type Ethernet DHCP Off IP addr Current IP Net Mask Current Net Mask Gateway Current Gateway DNS Server 4.2.2.1 Port 80 Band Width 0.0 Limit(Mbps) xDSL DDNS Radius User ID Guest Password ***** Status xDSL not connected Interval Off URL www.webgateinc.com Group Newbie Status Not Registered Status Disable IP Address 0.0.0.
Installaction & User Manual PTZ PTZ Home PTZ Off Idle 5 Time Monitor Audio Text Serial PTZ Port None PTZ Address 0 Monitor Minitor1 Alarm Pop-up(Sec) Off Scan Mode Over Scan VGA Mode 800x600@56Hz Monitor Switching On Audio Channel 1 Audio Recording Off Sync Video Channel Ch1 Audio Gain 0 Audio Mix Mix On Recording Off Sync Test With Ch1 Device Manual Seek Header Off Header 1 Header1 Header 2 Header2 Delimiter 0D0A Timeout(ms) 1000 Lines 20 Serial Port Com
Sensor Preset Sensivity 5 Area Set All Sensor All, N.O.
Installaction & User Manual List Program Res Fps Q Res Fps Q A D1 15 Q5 D1 15 Q5 B D1 7 Q5 D1 7 Q5 C D1 4 Q5 D1 4 Q5 D Half 30 Q5 Half 30 Q5 E Half 15 Q5 Half 15 Q5 F Half 7 Q5 Half 7 Q5 G CIF 30 Q5 CIF 30 Q5 H CIF 15 Q5 CIF 15 Q5 I CIF 7 Q5 CIF 7 Q5 MH3200M Rec mode List Normal Event Program Res Fps Q Res Fps Q A D1 15 Q5 D1 15 Q5 B D1 7 Q5 D1 7 Q5 C D1 4 Q5 D1 4 Q5 D Half 30 Q5 Half 30 Q5 E Half
4. Monitoring All analog video image channels connected to DVR is displayed to screen by Power connection. It is to utilize all monitoring mode of DVR. 4.1 Basic Screen After Power connection, the DVR operates on automately. It boots with LED on. 4.2 Single Full Screen Mode After press the channel number wanted or click mouse button. Press [MULTI] button to return to divisional screen 4.3 Multi Screen Mode Press [MULTI] for multi-channel display or click “Display” icon from Function menu.
Installaction & User Manual 4.5 Auto Switch Mode (Sequence) Defined channels or multi screens can be displayed in sequence with configurated time interval. Maximum 16 channels or multi screens can be defined. . 4.5.1 System Standard Mode By [SEQ] button, it can monitor auto switching of defined channels. Press [MENU] for the setting switching term or using mouse click menu icon from function menu. Move to “Device” “Monitor” from OSD menu.
4.5.2 User Sequence Mode [Press [AUTO] button or click [Sequence] icon from Function menu with mouse. Auto Switch model can be set from “Monitor” main menu. 4.6 Event Screen When the event is occurred, the green color [M] and red color [S] will be display from status bar. In case of [M] displayed, the camera name will be turned to green color, and it will turn to yellow when Motion Detection event finish.
Installaction & User Manual 1. If Alarm Pop-up Hold (sec) set to Off, Alarm Pop-up will not operate. 2. If Alarm Pop-up Hold (sec) set to keep, it does not return to previous screen before press any button. 4.7 Zoom Screen Mode From single full screen mode, press [FUNC] and D-Zoom button then select + button to - activate zooming the image. Default zoom screen locates to main center when press [ZOOM] button. Zoom image can - shift left-right in 18 steps and top-bottom in 12 steps.
4.9 PTZ Control Connect PTZ controller to DVR and set relevant protocol from “Serial” menu, then PTZ can operate while monitoring live images. Then PTZ works automatically with following icon. PAN/TILT can be used with directional button on front panel, and PAN/TILT/ZOOM can be used with mouse. Press PTZ button from DVR’s front panel, or click PTZ icon from Function menu to use OSD Menu, Focus, Preset, Aux.
Installaction & User Manual Below lists are protocols available in DVR Model Manufacturer BOSCH AutoDome, TC8560X-4 Bosch PELCO(P), PELCO(D) Pelco Sony EVI-D3x Sony VT VPT-4x VT AD Speed Dome AD SungJin SJ372R1 SungJin Samsung SCC641 Samsung Electric Panasonic WV-CS850 Panasonic SDZ160/330, Samsung SPD, Samsung Techwin Keyboard SCC3000A, Samsung SRX-100B LG GAC-PT2 LG Keyboard KBD300A, WGI SPD1800/2600 Honeywell WKC-100 Honeywell Merit-Lilin Fast Dome Merit Elmo PTC200C Elmo
4.9.1 Pan/Tilt/Zoom This menu is used to control Pan / Tilt / Zoom function. Select relevant channel to control PTZ which is connected with PTZ. 4.9.2 Focus Press [PTZ] button in PTZ screen to activate Focus menu. Control focus with [Near] or [Far] buttons . 4.9.3 Load Preset Press [PTZ] button in PTZ screen to activate Load Preset menu. Select Preset number wanted and press [Load] button 4.9.4 Save Preset Press [PTZ] button in PTZ screen to activate Save Preset menu.
Installaction & User Manual 5.Playback 5.1 Playback Mode 5.1.1 Playback on Standard monitor (16 / 9 division) - Please, push play button in monitoring mode or mouse click play button in Function menu. - If pushing Play button or FWD button, video playbacks in forward direction at 1× speed. - If pushing REW button, video playbacks in reverse direction at 1× speed. - If pushing Playback button in multi-division monitor mode, . 5.1.2 Playback function ◀▶ : Playback 1× speed.
5.2 SEARCH MODE This menu is to playback specific time data from the time frame and searching log at Playback mode. There are Time, Calendar, Event, Thumbnail mode. Please, push Search button on the front panel or click in Function menu.. 5.2.1 Time Search Select date and time to search and playback video will be moved to the selected point.
Installaction & User Manual [MH3200M] Display recording status of channel 1~32 Year : Select Year to search. With mouse wheel, user can change it. Month : Select Month to search. With mouse wheel, user can change it. Date : Select Date to search. With mouse, select the date and decide the time by wheel. Time 5.2.3 : Select the time and push Enter button to play back. Event Search User can search by all channels, some of channels, all events, motion detection, sensor in certain range.
Enter and change the value by Up and Down button. With mouse, click and scroll the wheel. Event Channel : Select the channel for search MH1600H, MH1600M: from Ch1 to Ch16 MH3200M from Ch1 to Ch32 Event Type : Select the event type for search There are all events, motion detection, sensor, video loss, text type Smart search : It’s a function that search the object by motion detecting. 1. Choose channel that you want to search. 2. Choose event type on MD(Motion Detection) 3.
Installaction & User Manual using up-down direction key or mouse wheel. Interval : Set Interval value by Up-down button or mouse wheel. View video : If pushing search button, 16 cycles will be shown based on start time. Press [Func] to return to the search or use mouse wheel. Select video : Play back from the selected video of thumbnail search result. With pressing Enter or clicking mouse, use can play back.
5.3 Copy This is for copying recorded video. There are CD/DVD and RE4 and AVI type. Copy function is supported to be used by user who has the authorization. For authority configuration, please, refer to 6.2.3 User setup To use copy function, press [COPY] or Click Copy button in Function menu. 5.3.1 CD/DVD This is copy function by using CD or DVD. CD or DVD will be automatically searched.. Type : Select CD/DVD using up-down direction key or mouse wheel.
Installaction & User Manual Please, refer to the recommended media list below. DVD-R manufacturer CD-R Manufacturer Mitsubishi(×16 recommended) Mitsubishi(×52 recommended) TDK(×16 recommended) TDK(×52 recommended) Imation(×16 recommended) Imation(×52 recommended) Sony(×16 recommended) Sony(×48 recommended) 5.3.2 RE4 User can back up by HDD, USB memory and play back suing mini-player or Control Center.
[MH3200M] Type : Select RE4 using up-down button or mouse wheel. Channel : To pop up the channel selection window, press Enter or use mouse wheel. Select Channel : use can select some or all channels and after selecting channel, press Enter or click mouse left button. Start time : Set start date or time to copy. After selecting part for change and set the value using up-down key or mouse wheel. End time : Set End date or time to copy.
Installaction & User Manual 5.3.3 AVI Use USB memory or HDD to copy certain part. Type : Select AVI using up-down key or mouse wheel. Channel : Select the channel to copy by up-down key or mouse wheel. From : Set start date and time to copy. Time and Year by left/right button and date/time by up/down button. With mouse, click left button first and use wheel. Duration : Set copy length. Copy as selected time length from the start using up/down key or mouse wheel.
6. Configuration 6.1 Recording Structure There are 3 modes in DVR recording. Configuration relation structure is like below. Please, refer to the below each item for detailed recording configuration. 6.2 System Setup Time and Disk and authority can be configured. 6.2.1 Date/Time Time set should be configured prior to the recording.
Installaction & User Manual Time configuration is very important to protect the recording data. Time change on recording is not recommended. Time zone configuration value of factory default is “UTC 00:00 Dublin” 6.2.1.1 Time Setup Caution: under recording, if user changes Time, it will affect time change on previously recorded video data in accordance with. Therefore, we recommend backup before time change. - Press Main Menu of Function or [MENU] button on the front panel.
Time With left/right direction key, use can move to year, month, day, hour in order and each configuration will be controlled by up/down key or mouse wheel. Apply User must push “Apply Date/Time” button. And you will see the below message box. Except date/time configuration, other configuration records automatically, but “date/time” configuration influences critical effect to HDD recording file system, It doesn’t record automatically. To apply the changed value, user must press [apply] button.
Installaction & User Manual 6.2.1.2 NTP Setup NTP(Network Time Protocol) make time of connected devices synchronized. There are NTP server and client which get time signal from the server. Sync NTP Set NTP function on/off. NTP Mode Configure NTP mode of DVR – Client / Server / All NTP Server Loc. When NTP mode is client, it is on Enable. Configure yes or no whether NTP server is in Local Network or Public. NTP Local server IP In NTP local server Enable, configure server ip.
6.2.2 Disk It explains how to add or remove or format internal or external HDD. Over Write If there is no space in HDD, old data will be deleted automatically. Disk Full Alarm Warning It gives notice if the recorded data is full up to configurated limitation of all HDD disks which is connected to DVR. Block Playback This function makes recording data seen during the limited area. For instance, if setting block playback by 2 day(Pic 2) among 10 days, just allowed 2 days data can be played back.
Installaction & User Manual 6.2.2.1 Disk Manager This is menu for the management of internal or external HDD. Manage status, bad block, size, Yes or No etc. Type : display location or type of disk. Int A (Internal A HDD), Int B (Internal B HDD), Ext (External HDD) Model : HDD model name. Bad Blk : display bad block. In HDD. If no problem, “0” will be displayed. Others are Not shown anything at all. Size : Display HDD size by MB unit Enabled : Make HDD enable mode or disable mode.
- HDD is not used. - If No, keep previous HDD without change. 6.2.2.2 Disk Status Temperature and status of HDD will be shown. 6.2.2.3 Disk Mirroring This DVR has DVR Mirroring function in itself and NVS Mirroring on NVS(Network Video Storage) via Gigabit Network [1 Without additional user control, if connecting DVR and NVS via Gigabit Network Cable, Mirroring function will be activated and user can operate it easily and simply.
Installaction & User Manual Mirroring Mirroring Mirroring Mirroring DVR Mirroring working method (1) Basically HDDs will be set like the above. (2) Recording data of HDD-3 is mirroring with HDD-1 and recording data of HDD-4 is mirroring to HDD-2. (3) If there are 4ea of HDDs are mounted on DVR and starts recording, HDD-4 will start recording. (4) If HDD-4 is full, automatically HDD-3 will start recording.
Mirroring configuration - Off : All mounted HDD will be recorded in order without Mirroring. - DVR : Mirroring recording only with internally mounted HDD ( not HDD in NVS04R) - NVS : Mirroring recording only with HDD in NVS04R which is connected to DVR. (Not HDD in DVR) - All : Mirroring recording with all HDDs in DVR and NVS04R. (1) Using directional key in Disk Mirroring configuration, please, select DVR for use and press Enter.
Installaction & User Manual 1. For Mirroring function, HDDs capacity and model for Recording and Mirroring should be same. If not, it won’t work. But, in case that HDD capacity is same but just different model, sometimes, it can not work properly.
IEEE1394, USB). 3. For Mirroring configuration in NVS04R or DVR, other HDDs should not be added except its Mirroring configuration. Ex) For NVS04R Mirroring configuration, all HDDs in DVR should be [NO] status. Recording Configuration. When using Mirroring function, according to configuration option, DVR system performance will be down and due to this reason, recording configuration will be adjusted automatically like below table chart.
Installaction & User Manual [ MH3200M / MH1600M Model ] DVR/All Mirroring Recording Setting Resolution IPS Quality D1 4~1 Q5 ~ Q1 Half 7~1 Q5 ~ Q1 CIF 15 ~ 1 Q5 ~ Q1 6.2.2.4 Mirroring HDD replacement. If Mirroring HDD free space becomes 0%, on DVR console screen, alarm pop-up message will be shown for Mirroring HDD replacement. This time, user can check Mirroring HDD free space in Disk Replace menu and user can replace it.
doubled block but it just points out that this Mirroring HDD is not replaced. Actual recording data is not doubled 6.2.3 User Setup There are administrators and user and administrator can use all functions. The max. Number of user is 10 people. Each user can use the function allowed. Authority setting If set to X for user authority, the function will be unavailable.
Installaction & User Manual Password change Select user Input password and press change Press Yes Password input box is displayed. Password can be input with front figure button or text input window. After inputing 5 digit figure, click “OK” button. After that, message pop up window will be shown and press “Yes”. Admin Password is “12345” in factory default and from user 1 to 10 in order “11111”,”22222”,..
6.2.4 Utility Configure the name of DVR, remote controller ID, Language. DVR Alias Set the name of DVR. DVR Keyboard ID This menu is to set the address of keyboard when using all functions of DVR by keyboard. Factory default is “1”. If user wants to control various DVR by one keyboard, its address should be set with the different value. Remote Controller ID Max 16 remote controller ID can be set and one remote controller can manage 16 DVRs. Registration order for Remote controller.
Installaction & User Manual - System will reboot. - Firmware update is done. System Log System Log shows boot status of system and user and configuration etc. . Factory Reset Change all configuration value by factory default.
Config Import/Export Export – Save Configuration data in DVR to USB Import – Apply exported Configuration data to relevant DVR or another DVR System Information Display recording status and system configuration of DVR Caution : This function is allowed only for system administrator.
Installaction & User Manual 6.3 Network This is menu for configuring network. Type Configure type of Network (Ethernet/xDSL). If connected to cable modem or LAN directly to DVR, configure by “Ethernet”. If DVR connects to xDSL- one of PPPoE type, configure xDSL. But if it is not type of PPPoE, configure ‘Ethernet’. DHCP With DHCP (Dynamic Host Configuration Protocol), all hosts connected to LAN can get Public IP address temporary.
DNS Server DNS1 is mandatory item to registry and use WRS and it should be asked to network administrator. UPnP Port Forwarding It configurates port of DVR automatically when DVR is used with internet hub. Port Port is necessary for Control Center and Webviewer connection. Reference : Basic port is 80 and if using PPPoE modem and AP, be careful typing port number. Bandwidth Menu for configuring network data transmission capacity.
Installaction & User Manual 6.3.2 WRS If DVR is connected to Cable modem or xDSL modem, IP address is changed at every connection to ISP. In this case, changed IP address can not be known. If DVR using static IP register into WRS server, changed IP address can be known easily when it connects to DVR. To register Static IP to WRS, please refer the following to set. WRS Interval For continuous registry, register interval should be set to ‘WRS Interval’.
6.3.3 Radius It makes to manage account information from several different DVRs to one account using Radius server. Please ask to Administrator before you use it. To set Radius, Status, IP Address, Port should be set. Set ‘Enable’ the status to use Radius and enter ‘Radius Server IP’ to IP Address. Standard port to use is 1812 and specific port number which is from Server is also useable.
Installaction & User Manual 6.3.4 Notifier To use Notifier (Notifier Protocol) function, please, refer to the tech manual or cantact Notifier administrator in advance. (Notifier™ device is for Fire Alarm. And if user enable Notifier function, DVR uses Notifier™ signal instead of sensor input of DVR.) In case of using Notifier function, Normal Recording under ‘Manual & Event’ will not work together. If you want to Manual & Event normal recording, please, make Notifier status disable.
6.4 Device Setup This menu is for configuring each camera connected to DVR. There are [name][Status][Color/black or white][Brightness][Contrast][PTZ] etc. Caution : NTSC and PAL camera can not be used at the same time. If changing the camera from NTSC to PAL, system should be rebooted. Configured value will be applied to monitoring and search at the same. 6.4.1 Camera Setup Select the camera to configure in Channel menu. 6.4.1.1 Title Configure camera name.
Installaction & User Manual 6.4.1.2 Using Channel Configure whether using camera or not. After pressing [Enter], select it using left/right key or mouse wheel. If user wants to enhance the recording or network monitoring speed, please, set the channel disable. 6.4.1.3 AGC (Auto Gain Control) AGC is the function to control the range of video signal input from camera connected. Configure Enable/Disable using directional key or mouse wheel. 6.4.1.
Covert channel With Covert menu, user can covert the channel in Live/Playback mode In Covert menu, all channel lists will be shown and press [Enter] button and click mouse to tick the channel. Checked channel will not show the video in Live/Playback. User sequence configuration User sequence can be edited. There are 16 user sequence mode and its interval is from 1 to 60seconds. Multi-mode The DVR has 3 predefined screen modes. 4C(4channels), 9C(basic 7 channels and additional 2 channels),10C(10 channels).
Installaction & User Manual 6.4.3 Audio Setup With this menu, user can configure Voice Channel, Audio recording, Volume, Synchronization, Mixing.. Voice Channel Select audio to use Recording Configure yes or no of using audio recording. If no, audio will be out only in live view and if yes, Audio will be out in both view modes. Volume Configure volume by +, - direction Synchronize Video Channel Configure which channel is matched with the input audio. If Audio no.1 is set to video channel no.
Voice mixing Select audio in live view. If setting by “Mix On”, all input audio will be out in every channels and if configured certain channel, input audio will be out on the selected channel only. 6.4.4 Text Setup Configure Text in Device menu. Recording Set On/Off of recording against Text input Sync Text with Select channel to synchronize with text. Device Select the device to input text. Manual, Star Finger 007, VSI Pro are available to select.
Installaction & User Manual Header check It has the various type of data input from the external device (Access Control, POS, ATM etc.) but it’s not necessary for a device which is supported its protocol by DVR .Like VSI Pro, VSI Pro Hydra, and Star Finger 007, it is not needed when the protocol of these device have implemented on the device. If not, this is the parameter to analyze how the one of data is constructed from the text data that is input continuously. Namely, all data has the first and the end.
6.4.5 Serial Setup DVR has 3 serial ports. One is RS-232C(D-Sub) and the other 2 ports are RS-485(Terminal). Serial Port Select Serial port. Device Select the connected device. Interface Configure which interface user uses. COM1 is for RS-232C, COM2 and COM3 is for RS-485 Baud rate/Parity/Stop Bit/Data Bit In put suitable value according to external device. 6.4.5.1 PTZ Setup Additional configuration for PTZ Address, PTZ port.
Installaction & User Manual PTZ Home Shift to preset assigned if it has no movement in certain time while PTZ control. PTZ Idle Time If it has no movement during configured time, shift to PTZ Home. PTZ Port Select Port for PTZ PTZ Address Configure the address configured in PTZ.
6.5 Event Setup There are 5 items such as event, Text, Sync Event, Preset, System event. 6.5.1 Event Check There are 3 items – Always, not apply, Custom. In case of Custom, with similar configuration window like schedule, user can configure event per weekday/time. • Time : Set time applicable • Daily : Adapt selected schedule to whole day of the week. • Delete : Delete Schedule Configure If time set, the content will be shown at schedule table.
Installaction & User Manual Not selecting schedule and click delete button, it’ll delete selected schedule first. How to change Select Schedule to edit and change weekday, program,time directly. In case that Schedule 50 are all configured, select the time zone to change by mouse click and click the time again, previouse configuartion will be deleted and new configuration will be shown. 6.5.2 Sync Event Configuration for Event synchronization.
System Event source System Event source can configure Bad block, Disk full, Fan error, authorization failure, WRS registration failure, Mirroring failure, Abnormal recording stop. 6.5.2.1 E-mail address Input E-mail address to get event alarm by E-Mail.
Installaction & User Manual Sender Address Not mandatory but necessary for receiver to find out which DVR sends event. Authentication There are 3 ways to send E-mail, Non-authentication sending, SMTP server authentication, TLS authentication. Non-authentication is to send e-mail without authentication from authentication server. SMTP server authentication is to send e-mail after an authentication of sender’s e-mail address from SMTP server.
Server URL Enter the FTP server address to send image. User ID Enter the relevant ID when FTP server authentication is set. Password Enter the password FTP Directory Select Folder to save image If folder is not indicated, the image is sent to the folder which server selects. 6.5.2.3 Twitter connection Twitter can be connected to send single image or text message about event information of the channel when event is triggered on the channel.
Installaction & User Manual Action Duration This is setup for transmission duration of the Twitter Please select Normal Event or System Event to be used for Twitter transmission Twitter ID Type in Twitter account to be used Login Status It shows current log in status Generate PIN Click on this to have URL information to log i Login URL Put URL from Generate PIN menu above into browser of PC then log in window come out and please log in with personal Twitter account PIN Type in PIN number provided after
6.5.2.4 Relay When event is working, set to relay as a output. To work relay, select event between normal and system event. 6.5.2.5 Buzzer When event is working, set to buzzer as a output To work buzzer, select event between normal and system event. 6.5.
Installaction & User Manual Channel All or certain channel. Sensitivity Sensitivity can be configured from min.1 to max 10. Area Select detection area. User can select all or certain channel. User Area When selecting per channel, it can be configured. 1 grid size is 22x15 and factory default value is all. If pushing user area, configuration window for detection area.. With direction key, select area and press [Enter] or click mouse.
6.5.4 Sensor This menu is to setup the existing sensor input and type of sensor. 16 inputs Sensor has 2 types, Normal Open(N.O.) and Normal Close(N.C.). 6.5.5 Preset In PTZ function, make configured preset work according to sensor input. Please, configure preset per PTZ. After selecting channel in preset menu, select event to work preset. Event can select sensor,MD,Text, its preset can be configured up to 16.
Installaction & User Manual 6.6 Recording setup There are 3 mode for recording – schedule recording, manual recording, event recording. Schedule recording records according to the configured schedule. And manual recording records via pushing “REC” button and event recording records when events are on. 6.6.1 Program setup Using [Program], adjust frame rate and quality and resolution and configure recording program for Manual&Event&Schedule.
Max R/F Max R/F shows the number of frame available according to the selected resolution. For instance, if it is set by 30fps at CIF, it means that the channel can record up to 30frame at CIF resolution. Reference : how to calculate recording performance D1[704x480] = 2 x Half D1[704x240] = 4 x CIF[352x240] If 480 frames can be recorded at CIF resolution, instead of it, 240 frames at Half D1 and 120frames at D1 resolution are possible.
Installaction & User Manual 6.6.2 Manual/Schedule recording setup With the change of recording mode, manual recording or schedule recording can be at one’s choice. And their resolution, frame rate, quality will be in accordance with the program. . 6.6.2.1 Manual Recording Only in manual & event recording, manual recording runs and when pressing [REC] button, recording starts. If you want schedule recording, recording mode should be Schedule & Event.
6.6.2.2 Schedule Setup It records according to the programmed schedule automatically. Make recording mode Schedule & Event and configure day and time. Check and select each program default value and select one of 9 programs from A to I or Several programs. • Program : Set recording program(A~I) • Time : Set time applicable • Daily : adapt selected schedule to whole day of the week. • Delete : Delete Schedule Configuration If time set, the content will be shown at schedule table.
Installaction & User Manual Edition Select Schedule to edit and change weekday, program,time directly. In case that Schedule 50 are all configured, select the time zone to change by mouse click and click the time again, previouse configuartion will be deleted and new configuration will be shown. Caution : If selecting the same time twice, “!” will be shown on the chart. When configuring time sector, previously configured time can not be included. 6.6.2.
In “Always”, event works all the time and in “Custom”, works during configured time. Configuration of Custom is similar with schedule configuration and can configure weekday, time for Event. • Time : Set time applicable • Daily : Adapt selected schedule to whole day of the week. • Delete : delete Schedule Configuration If time set, the content will be shown at schedule table. Click to schedule start and end by mouse, the schedule will be shown at schedule table.
Installaction & User Manual 6.6.2.4 Continuous Recording Only continuous & event set can record continuously, select Continuous & Event in the menu, it starts to record.
7. Web Viewer WebViewer is Web application program loaded to monitor real-time image or to monitor the images recorded through Web browser to PC located remotely. WebViewer is divided into Login page and Monitor to do monitoring real-time images, Playback to replay recorded images. 7.1 System requirement Minimum Recommendation CPU Core2Duo / 2.0Ghz Quad Core / 2.
Installaction & User Manual 7.2 Login After input IP address that set to system, then WebViewer Login page will be connected. Input the set of User ID & Password, click ‘LOGIN’ to access. If didn’t change the password in Control Center, ID and Password will be admin/12345. ID can not be changed.
7.3 User Setup To access WebViewer, user authority and password can be changed in DVR or Control Center configuration In account menu, user password can be changed. Basic admin password is “12345” and user password is like “11111{“, “22222” ~~, user10 is “00000”. Valid password is 5 digits. Authority configuration is almost all the same in DVR and Control Center. But quick recording, backup, audio, yes or no of using channel are only possible in Control Center. 7.
Installaction & User Manual Webviewer Installer Login page provides manual installation program to use WebViewer function. PC that access to WebViewer first installs ActiveX to use WebViewer’s function. At this time when installation is not smooth, installation program needs to download from Login Page and install manually. Caution When install WebViewer Installer, it must close all program related to Control Center. It might not be efficient to install. 7.
Double click on one of the playback screen to convert in 1 channel mode. After conversion to 1channel mode, double click on screen to return to previous division channels. At division screen, it can change screen location. If 3channel image moves to 6ch, drag 3ch image and drop on 6ch location so as to exchange between 3ch and 6ch image 7.5.2 Move to Playback Move to playback with clicking the above image.
Installaction & User Manual 7.5.3 Channel On/Off It is On/Off button for the Channel located to left in page. Click the channel wanted to on or off. And Default is on. 7.5.4 Sensor Indication The icon indicates when sensor occurs in system When it sensors, relevant sensor icon comes to Red, and indicates sensor number of video. 7.5.5 Relay operation It can on or Off Relay of the unit. Click the number button to activate Relay On, then the icon changes from Blue to Orange color.
7.5.7 Event Data It shows real time event data occurred at the bottom of monitoring page. Indicated Event data list are as follow.. (Table, Event Icon) Icon Function Motion Detect On , Sensor Input , Relay Output On , No Video, Video Detected 7.5.8 Video Recording & Save Saving 7.5.8.1 Video Recording During monitoring, it can record max. 10 minutes of video by click Quick Recording button “ ”. During Quick Recording, recording time is indicated on video.
Installaction & User Manual 7.5.8.2 Saving Video There are 3 types for saving Video - jpg, bmp, eye, saving means the function to record 1 frame of current monitoring channel. To save video, select the channel and click right button of mouse. And select “Save As” and point out the location and press Save button. 7.5.9 Using PTZ Among the icon on top of video on monitoring, click ‘PTZ’ to activate interfacing to control Pan, Tilt, Zoom, and Focus.
Reference Supported PTZ camera list can be refereed to ‘4.8 PTZ manipulation. 7.5.10 Using Audio In case of Channel setup sync with Audio, press right mouse button on the image to activate pop-up menu to “Listen” or activate Audio listen button. First default is Mute. In case of listening Audio, select pop-up menu or button. After cancelling mute, control audio volume. It can mix several channels of audio 7.5.
Installaction & User Manual 7.6 Playback This page is to playback recorded images, and user who has authority of ‘HDD’ among user ID or administrator can use this function. Playback that is made up 16 divisions can play the images by searching through colander by recording period and moving the period. It can backup recorded image and also print Pause image or save to Bmp file. 7.6.1 Video Division & Changing Channel Playback supports 1, 4, 9, and 16 divisional screens.
Save Image dialog box appears, then it can input message or select channel name, date, event data. Press ‘OK’ to open dialog box for the saving location, then save bmp file. 7.6.3 Print Select image with mouse for the channel to print image saved, and then click ‘Print’ button. Window comes to input Memo, and click ‘OK’ button to print the image through the printer connected. Print material includes ‘Printing Date’, ‘Channel name’, ‘Recording Date’ ‘Event’, ‘Memo’. 7.6.
Installaction & User Manual 7.6.5 Web Monitor Click ‘Go’ button at top of page, and it can move Web monitor page. 7.6.6 Channel On/Off It is the same function like Channel On/Off function at Web Monitor. It is Channel On/Off button located on right of Page, and click on or Off page for wanted channel. Default is on. Disabled Channel button refers to do not support and relate to this unit. 7.6.
7.6.9 Functional function at the bottom of monitor ① Indicates playback range of recorded image. ② Press button as the time set at (5) so as to change the time zone to playback in forwarding and backwarding. ③ From left button, it can ‘Move a frame back’, ‘Play backward’, ‘Stop’, ‘Play’, ‘Move a frame forward’. ④ It is the function to set play speed. After click the button, it can set the play speed ‘0.5x, 1x, 2x, 4x, 16x, 32x, 64x, and All’. ⑤ It is the function to set play area.
Installaction & User Manual 8 JAVA Viewer Java viewer is a web viewer to use in Java. Java should be installed in login screen to use Java viewer. After an installation of Java manually, select “Java” in below of Password window and login. Then single screen of video channel 1 is displayed Multi-screen display, Event, Relay can be used in Java viewer. To change Multi screen display, click 1,4,8,16 in right side.
9 User manual for Mobile Viewer Mobile viewer is viewer service to monitor video via mobile device. To access mobile viewer, user uses mobile device supporting Wi-Fi or smart phone or 3G. 9.1 Log-In page Below picture is Mobile viewer log-in page. To access log-in page via mobile viewer, please, type the address like http://IP/mvmenu.html. Below image is accessed login page to http://211.53.133.187/mvmenu.html .
Installaction & User Manual For functions, please, refer to the below. [0] MENU : Move to Log In page [1] CH- : Move to the previous channel.
Trouble shooting 1. DVR booting failure 1. Check the power 2. Check Power cord 2. No video on monitor 3. Check monitor power 4. Check cable between DVR and monitor 5. Check monitor cable port 6. Check DVR power is off 7. If monitor video is gray mode, check the camera type(NTSC/PAL) and reboot. 3. No video in some of channel 8. Check Camera power 9. Check Camera video input 10. Check DVR input port 11. Check On/Off of Activity configuration of Screen 12. Check Covert configuration of Monitor 4.
Installaction & User Manual 9. If network is not working 25. Check if Network cable is connected 26. Check DVR IP 27. Check Computer IP 28. Ping Test 29. Check PC specification if Webview video is not shown. 10. The cases necessary to contact the shop 30. In case of extraordinary working(ex: noise, smell or fume) 31. Connector breakage of power cable 32. In case that rain or water is in the product 33. In case that liquid or foreign is in the product 34.
The way to check the manufacturing date It can be checked with its S/N(Serial Number).. S/N : Serial Number It means composite 12 digit number with product model name and production year, month, and week. It can be found on the attached label attached on the bottom of product or system info of configuration tool or system information 1 of DVR Func menu.
Installaction & User Manual Available HDD Please ask to seller about HDD available with DVR.
Continuous & Event Schedule 24hrs / 7day Playback Instant playback / Search Mode Speed Search Type Time, Calendar, Event, Thumbnail Block Playback 0day ~ 99days Event & Alarm Event source MD, Sensor, Text Event check schedule 24hrs / 7day Event Action Relay, E-mail, Buzzer, Twitter, FTP MD Area 22x15(NTSC), 22x18(PAL) Sensor input dry contact (N.O. or N.C.
Installaction & User Manual User privilege Menu, PTZ, Relay, PB, Power on/off, Backup IP Filtering supported Storage/Backup Storage Devices 4 internal SATA HDDs, 1 external eSATA I/F NVS04R File System Proprietary file system, data-loss protection against power-failure Capacity Max 32TB with NVS04R Backup type multi-channel or single channel avi file Backup device internal CD/DVD or USB drive S.M.A.R.T.
Product Dimension MH1600H
Installaction & User Manual MH1600M 144
MH3200M
Installaction & User Manual 146
Open Source License Report on the Product The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to . If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
Installaction & User Manual Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
Installaction & User Manual License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole.
offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License.
Installaction & User Manual This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8.
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Installaction & User Manual Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users.
Installaction & User Manual danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free. The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS 0. Definitions. “This License” refers to version 3 of the GNU General Public License. “Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
1. Source Code. The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work. A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
Installaction & User Manual You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright.
source code under the terms of section 4, provided that you also meet all of these conditions: a) The work must carry prominent notices stating that you modified it, and giving a relevant date. b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact all notices”.
Installaction & User Manual with such an offer, in accord with subsection 6b. d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code.
service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Installaction & User Manual All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term.
does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so. 10. Automatic Licensing of Downstream Recipients.
Installaction & User Manual In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program. 13. Use with the GNU Affero General Public License.
Installaction & User Manual PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. Limitation of Liability.
(at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . Also add information on how to contact you by electronic and paper mail.
Installaction & User Manual Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it.
ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom.
Installaction & User Manual Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1.
License. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.
Installaction & User Manual You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License.
explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License.
Installaction & User Manual Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14.
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.
Installaction & User Manual "Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License. "Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form. 3. Grant of Patent License.
Installaction & User Manual modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License. 5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions.
To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information. (Don't include the brackets!) The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives.
Installaction & User Manual THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
telnet-server license: Copyright (c) 1989 Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Installaction & User Manual following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. Neither the name of Yahoo! Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission of Yahoo! Inc.
The name of the University may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. c-res license: Copyright 1998 by the Massachusetts Institute of Technology.
Installaction & User Manual Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission no
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
Installaction & User Manual This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.] SIL OPEN FONT LICENSE Version 1.
Installaction & User Manual PERMISSION & CONDITIONS Permission is hereby granted, free of charge, to any person obtaining a copy of the Font Software, to use, study, copy, merge, embed, modify, redistribute, and sell modified and unmodified copies of the Font Software, subject to the following conditions: 1) Neither the Font Software nor any of its individual components, in Original or Modified Versions, may be sold by itself.
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.
