TritonHD User Guide MD1600H (v 1.
FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Important Notice 1. Do not place heavy objects on the top of the TritonHD. 2. TritonHD is for indoor use. It is not weatherproof. Use TritonHD with referring to its environmental specifications (Temperature & Humidity). To clean the TritonHD, gently wipe the outside with a clean dry cloth. 3. TritonHD uses AC power of 110V ~ 240V. Be cautious not to cause electric damages to TritonHD. 4. Be careful not to drop the TritonHD. Physical shocks may harm the product including internal HDD.
Contents Overview.................................................................................................................................... 7 1. Introduction ......................................................................................................................... 7 2. Description........................................................................................................................... 9 2.1. Front Part ............................................................
4. 3.11. Screen Lock control ...................................................................................................... 20 3.12. Utilizing Quad monitor .............................................................................................. 21 3.12.1. Monitoring ............................................................................................................ 21 3.12.2. Monitoring & Playback .................................................................................
5.6.2. Setup .................................................................................................................... 52 5.6.3. System Alarm........................................................................................................ 53 5.7. Monitor Setup............................................................................................................... 55 5.8. System Setup...............................................................................................
Overview 1. Introduction TritonHD MD1600 Series is new conceptual DVR (Digital Video Recorder), which can record 16ch ananlog video channel, Audio, Text & Alarm data etc simultaneously. Also, it upgrades video quality and file size applying MPEG algorithm. Quick Setup menu in TritonHD MD1600 Series makes possible to direct recording by only connection between Power & CCTV video. Quick Setup menu is programmed to optimize video quality and recording performance.
Main features - It supports 16ch video - Supports 4 ch bi-directional audio - Supports recording, playback, network recording, network playback simultaneously (Pentaplex) - Max. 480(MD1600H) ips recording speed - Max.
2. Description 2.1. Front Part 2.1.1. MD1600H front part (1) Status LED (2) Remote controller (3) Power switch receiver (4) USB Interfacer (5) Function buttons (6) Channel button (7) Menu & Directions (1) Status LED Power : It indicates Power input, and light on at Power in. Network : Indicates Ethernet & communication status and twinkle as much as image delivery via Ethernet.
(5) Function buttons COPY : Function to copy recorded images In single monitoring mode, press the button to activate COPY menu SEQ : Function to diplay all video connected sequentially Press more than 1 sec. to operate User Sequnce mode MULTI : Function to monitor multi video images in a screen((4/9/16 division channel) SELECT : Function to select video channel to control PTZ in Monitor model. And function to select video channel to Copy/Backup/Delete in Playback mode.
싱글/분할 모드에서 다음 채널 또는 분할 모드에 맞는 채널 그룹으로 전환 합니다. 2.2. Rear Part 2.2.1.
2.3. Summery of Installation - Camera connection - Monitor connection - Ethernet connection (for remote connection) - Audio connection - Power connection & Operation Extension through NVS04, IEEE 1394b will be supported later. For the details, please contact to local distributor.
Basic Structure 3. Monitoring All analog video image channels connected to TritonHD is displayed to screen by Power connection. It is to utilize all monitoring mode of TritonHD MD1600 series. MD1600H support Quad monitor (1~4) and Monitor 1~4 supports all following functions. Therefore, the following functions explains base on all Monitor 1~4. 3.1. Basic Screen monitoring - After Power connection, MD1600H operates on automately. - It boots with LED on.
3.4. Manual Recording By the press [REC] button for user recording, it records as long time as it set the time. It is prior to Normal Rec, Event Rec. And it records by user recording set in disregard for any recording setup when user recording starts. 3.5. Auto Switch mode There are System Standard modes and User Defined mode in Auto Switch mode. And Users Sequence mode operates by the press [SEQ] button 1 sec longer.
3.5.1. System Standard mode - By [SEQ] button, it can monitor auto switching of all channels. - Press [MENU] for the setting switching term. - Move to “Monitor” from OSD menu. - Press [▷] to move from “Monitor” to “Monitor 1”. - Select “Seq. Switching (sec)” and set value from 1 sec. to 60 sec. At OFF set, auto switch mode does not operate. - Auto Switch mode can be set in every division mode by the press [SEQ] button. - Press [SEQ] button once more to leave from Auto Switch mode.
3.5.2. User Sequence mode - Press [SEQ] button longer than 1 sec. - User Sequence is to set User Sequence Configuration from “Monitor 1” in OSD menu. 1. User mode can define max. 16 channels. 2. The above picture defines 6 Sequence, and it is displayed in order as 4 division(1,2,3,4) Æ Full screen(1) Æ 4 division(5,6,7,8) Æ Full division(9,10,11,12,13,14,15,16).
3.6. Alarm mode - It can be set to Pop-up automatically relevant screen when alarming. - Set pop-up period can be set into “Alarm Pop-up (sec)” inferior to “Monitor” menu. - At the simultaneous alarming in several channels, it displays the division as many channel as alarmed. For example, when 3 channels alarm, 4 divisions is displayed on screen. And press any button to return orginal channel. 1. If Alarm Pop-up Hold (sec) set to Off, Alarm Pop-up will not operate. 2.
3.9. PTZ Control Connect PTZ controller to TritonHD and set relevant protocol from “Serial Setup” menu, then PTZ can operate while monitoring live images. - Press [SELECT] button first. - Channel select icon is on the screen, - Shift to channel to control PTZ with directional key. (Press [SELECT] at single screen mode) - Press [MENU] at channel selection icon displayed to view PTZ (Pan/Tilt, Zoom/Focus, Load Preset, Save Preset). - Select any wanted menu from them and press [ENTER]. 3.9.1.
3.9.4. Utilizing Save Preset This menu is used to set new Preset at real-time monitoring mode. - Control camera location using ‘Pan/Tilt’ and ‘Zoom/Focus’ menu. - Press [SELECT] button and select Channel. - Press [MENU], then select ‘Save Preset’ from OSD. - Press relevant Number button to set in Preset. 3.9.5. Utilizing Clear Preset This menu is used to initialize Preset at real-time monitoring mode. - Press [SELECT] button and select Channel.
3.10. Relay control The function to Relay On/Off. (MD1600H supports 4 Relay Output.) - Press [RELAY] button to display “Relay On” icon on screen. - Then Relay Out signal is out by pressing the relevant number of Relay among 1~4 number button. - Press [RELAY] to Relay Off. - Display “Relay On” icon while Relay On is working. - Then “Relay Off” icon is displayed on when press [RELAY] button once more. - Rress relevant Relay button to Relay Off. 3.11.
window for user password input will be displayed at any button press. And Lock mode will be released with correct password input. 3.12. Utilizing Quad monitor 3.12.1. Monitoring Monitor 1 monitors several video channels, and Monitor 2 is for bigger screen of channel 1. Also Monitor 3 for Sequence mode and Monitor 4 is capable of monitoring Alarm Pop-up images. Every Monitor 1~4 can be set in following conditions separately.
3.12.2. Monitoring & Playback Monitor 1~4 are capable of searching several video/playback in single & divided sreen. Namely, several channels can be monitored and playback separately and simultaneously. But Playback can be monitored in 1 monitor among Monitor 1~4, and the rest 3 monitors for monitoring.
4. Playback 4.1. Various Playback mode (Playback) 4.1.1. Playback on standard monitor (16 division) - Press Playback button [▷] at Monitoring mode. - It playback images with initial 1x speed. At Monitor mode, Playback buttom will play the recorded image from Channel 1. Namely, it will always start playback of channel 1 from 30sec. ago. At the time, the data of image will be shown at the bottom of screen. And the one on top indicates images for 30 min. and the bottom indicates 12hrs.
4.1.5. Various Playback functions ▷ (PLAY) : Playback 1x speed. Press [▷]playback button at single monitor mode will playback recorded images of monitoring channel. Press [▷]playback button at multi monitor mode will always playback recorded images of no. 1 channel. When the execute playback by pressing [▷] playback button, it playback from the time when user connects to playback lately. STOP : Stop Playback. PAUSE : Pause Playback. FFW : Change Playback speed at every button pressing.
4.2. Search mode This menu is to playback specific time data from the time frame and searching log at Playback mode. From for the time to start recorded data, To indicates the last time. Select From/To and press [ENTER] to move to the relevant time. - Press [SEARCH] at Playback mode. - Input Date/Time or select relevant Log from Log Browser. - Press [▷] button. - Playback searched image. - Press [EXIT] to exit from Search mode. How to use Log Browser 1.
4.3. Copy / Backup / Delete This menu describes how to copy/backup/delete recorded images. - Press [SELECT] and [MENU] in order and Playback mode. 4.3.1. Copy Image Use USB Memory Stick etc to copy selected channel images in some part. Time Slect the range of Copy. Range of image can set 1sec.~1hrs. from present playback location. Select Disk Slect the target of Copy.
4.3.2. Backup Data Start Date & Time / End Date & Time Select the range of backup. Select Disk Select the disk to use backup device. Uncompleted backup file 100% can not be played normally in PC It does not support USB device as backup. It supports CD-R/DVD-R, and over (CD-R Media 700MB / DVD R Media 4G) in CD-R Media. It creates re4 in HDD re4, in CD-R vfs4. It supports only DVD backup. CD backup will be supported later. For the details, please contact to local distributor.
4.3.3. Delete Data The menu to delete specific rage of data in present HDD recorded. Delected data is limited to present HDD used, and it does not affect to backup disk. The range of delete data is from oldest data to the data that the time selected. The size of block in TritonHD file system is 64MB and delect data is carried in block. So Delete data does not define the accurate time data.
5. Configuration 5.1. Quick Setup There are 3 methods in Video recording setup - Quick Setup, Recording, Alarm Recording menu. Quick Setup is the menut to set recording easily in same condition of all analog channels. Recording is to set recording in more various conditions by time period or channel. Alarm Recording is to set the recording with alarm. Also, Quick Setup includes Time Set menu. 5.1.1. Tim Set(Date/Time) Factory set of TritonHD comes to “UTC 00:00 Dublin” as Time set.
Time Zone Select the times using left-right directional key from TritonHD front. Every time pressing direction changes the time zone. (Press [EXIT] to return to previous menu. It is as same as OSD menu.) Daylight Saving (Summer Time applied) This menu is linked to Time zone set menu. Namely, it is activated when selected summer time zone is set from Tim Zone set menu. Summer Time Zone is programmed to apply the time zone from existing MS Windows.
Selet the method of Time Format. Using Legt-Right key set Time Formate “MM/DD/YYYY” or “YYYY/MM/DD”. Date/Time Using Left, Right key will shift Year, Month, Date menu, and select each menu with Upper & Lower button. Apply Date/Time To apply Date/Time value, press “Apply Date/Time” button to display the following window. Other setup can be saved automatically by closing setup menu completely, but “Date” & “Time” does not because it can affect HDD recording File System critically.
5.1.2. Recording Setup Quick Setup is to set same conditions to all analog channels in every hour.
Channel Status Set whether it activates all analog channels. Defult value is “On”. Recording Speed/Quality There are all 5 setup conditions. (No Rec./Low/Standard/High/Custom). The conditional Setup except “Custom” comes to auto synchronize with “Speed (ips)”and “Quality”, Quality can set the each separately. At the setup condition of “Alarm Recording”, “Standard”와 “Pre/Post Alarm” is set to each 1 second. Resolution Recording resolution of all cameras [CIF /Half D1/ Full D1].
5.2. Camera Setup This is to setup the condition of every camera. At Quick Setup menu, it sets every camera to the same condition. Set values are applied in same at monitoring & recording mode.
Display Letter input window to input characters. According to menu, letter input window can be different, but Set is the same. - Use direction key for letter input. - Select letter using [▲/▼] button. - Press [►] to input after select the input letter. - Press [◄] to Shift back and delete. - Avaiable letters Digit :1234567890 Capital letter :AB C DE F GH I J K LM N O PQR STUVWXYZ Small letter :abcdefghijklmnopqrstuvwxyz Special letter :( ) - .
Brightness/Contrast Select the value from “–9” and “+9” using [◄] or [►] buttong after pressing [ENTER]. Covert Covert On will hide the channel at Monitoring mode. Select “A / B / Both / Off” using [◄] or [►] buttong after pressing [ENTER]. PTZ Home/PTZ Idle Time Shift to Preset assigned if it has no movement in certain time while PTZ control Set Preset number and Time using [◄] or [►] buttong after pressing [ENTER].
5.3. Manual Recording setup This menu is to set video recording condition by user when pressing [REC] button. If manual recording starts, Normal Rec & Event Rec is ingored and it records based on user recording setup. Recording Speed/Quality There are all 4 setup conditions. (No Rec/Low/Standard/High/Custom). Setup condition except “Custom” will synchronize “Speed (ips)” and “Quality” automatically, Speed(ips) and Quality can be set each separately. Pre Alarm (sec) It can set max. 5 seconds.
1. In case of set ‘No Rec.’ in Schedule Rec., it records as a set of Pre Alarm. While Schedule Recording, it records Pre Alarm section in speed(ips) of a set Schedule Rec. 2. When Post Alarm is set to Latched, it maintains user recording continuously till the stop pressing [REC] button by user. 5.4. Schedule Recording Setup This recording is to set the recording conditions by Channel and Time schedule.
1. The difference of recording setup in Quick Setup is that there is no audio recording setup, and sets whether Special Time Recrding & Event Recording sets or not. 2. What Alarm Recording Off is set, Alarm Rec. menu is not available. To set Alarm Rec. menu, Alarm Recording of Recording menu should be set to “On” and press “Apply” to complete setup. 4. Refer to the following Setup by Channel how to set in detail. 5.4.2.
Resolution There are all 3 conditions. (CIF/HALF/D1) At this menu, resolution set is applied to every User recording, Event recording. - CIF : 360x240 @ NTSC, 360x288 @ PAL - HALF : 720x240 @ NTSC, 720x288 @ PAL (HALF D1) - D1 : 720x480 @ NTSC, 720x576@ PAL (FULL D1) Special Time Recording This menu is to differenciate recording conditions by setup of specific time zone. Namely, if it sets to day time in workday, it can record according to 2 type setup condition. Specific time sets from ‘System’ menu.
Event Recording After pressing [ENTER] button, set “On/Off” using [◄] or [►] button. Detailed Alarm recording conditions sets from “Alarm Recording” menu. Here only can set recording according to alarm recording setup. 5.5. Alarm Recording Setup This menu is to set Alarm Recording condition. After setup Recording condition, “Event recording” menu from “Recording” must be “On” to setup Alarm recording in TritonHD. Also, before setup Alarm recording, “Alarm Source” must be set. 5.5.1.
Configuration It can set 16 sensors (S1~S16) separately. 5.5.2. Motion Detection Setup This menu is to set MD of each channel. Global sets all channels (Cam #1~Cam#16) in the same together, and setup can differ separately. Motion Detection It sets 4 different sensitivity of MD; Off, Lowest, Low, Std, High, Highest. MD Area It sets MD zone. 64 (width 8 x height 8) zone is selected by “Set All” and release it with “Clear All”. To set Global, press “Apply”. Other will be not applied.
5.5.2.1. Motion Detection Setup by Channel MD setup by channel is same as Global setup. And it can set MD zone additionally when MD sets by channel. Custom Area It sets MD zone by user NTSC 22x15, PAL 22x18 First default value is set to “Select All”. If “Custom Area” pressed, Window for MD zone setup is opened.
< MD Zone Setup > It can set MD zone by user directly. If “Custom Area” is pressed, sell NTSC 22x15, PAL 22x18 for setup is displayed. Selected MD zone is in grey color. To select MD zone, use direction key for the wanted zone and press“ENTER” to apply. After selection, press “EXIT” to return previous menu.
5.5.3. Text Setup This menu is to set text data input. It has to be set COM1 part from “System -> Serial Setup” menu on OSD. Recording It is On or Off to save the Text input. Sync Text With Select the channel synchronize with Text data. Seek Header It has the various type of data input from the external device (Access Control, POS, ATM etc). Like Star Finger 007, it is not needed when the protocol of these device have implemented on the device.
Delimiter Value of Delimiter can be different according to every device. Refer to their manual or inquire it to purchasing stores of its model. Timeout (ms) Following lines defined here means maximum number of text line from one data. Even if there is standized data, there can be a short and long data. For example, there are 3 lines to write names on ATM. But some may need only First name & Last name to register. Which it means requires only 1 shorter than other ATM users.
5.5.4. Global Alarm Recording Set all analogue channels in same condition. Sensor/MD Set synchronizing with Sensor/MD. Pairing means 1:1 synchronization between the channel and Sensor/MD. Text When set “On”, it deals text input of relevant channe as Alarm Event and is saved. 1. To apply Global setup, press “Apply” button. 2. Refer to following Setup by channel for the details.
5.5.5. Setup by Channel Alarm Source (*=All) - Through Alarm Source, 4 Sensors and 1 MD, Text input is selectable. - Selection of Sensor is set by pressing relevant number button. - Selection of MD, Text can be On/Off by direcitional key. - Select Preset of PTZ by relevant Alarm input. 1. * : Press ▷ button. 2. – or # : Press number 0 button. Recording Speed/Quality There are all 4 conditional setup (No Rec/Low/Standard/High/Custom).
Post Alarm (sec) It can set max. 60 seconds. 1. In case of set ‘No Rec.’ in Schedule Rec., it records as a set of Pre Alarm. While Schedule Recording, it records Pre Alarm section in speed (ips) of a set Schedule Rec. 2. When Post Alarm is set to Latched, it maintains user recording continuously till the stop pressing [REC] button by user. Alarm Recording Status It can check ON/OFF of Alarm Recording menu in Schedule Recording setup.
5.6. Alarm Action Setup According each Time schedule, it sets Relay action. It sets to 5 different time period, Full Time, Weekday(Day), Weekday(Night), Weekend(Day), Weekend(Night). After Schedule setup, it sets Relay, Buzzer, Email etc to operate Alarm action. 5.6.1. Schedule Select Action Source Sensor and MD can be set max 4 or ANY for Relay1~Relay4, Buzzer, E-mail. Video Loss and Text can be set On/Off. Selection of Sensor/MD is done by pressing relevant number button. 1. ANY : Press ▷ button.
5.6.2. Setup Relay Configuration Set the use or not for R1~R4. Buzzer Set the use of Buzzer or not. E-mail Addr. Input E-mail address to inform Alarm. Sender Addr. Input “Sender” address in the typr of who@where. Mail Duration (min) E-mail notification is to send message in terms of Mail Duration set, but not every time that Alarm is occurred. It can be set from 1 to 30 minutes.
Network setup is set to DNS for E-mail notification. 5.6.3. System Alarm 5.6.3.1. System Alarm Setup It is to set ON/OFF of Alarm for the notification of system faulty. HDD Fail Alarm action is operated when HDD disconneced or abnormal action. HDD Almost Full It operates alarm action when connected HDD is almost full. Fan Fail It operates Alarm action when malfunction of FAN connected to TritonHD.
Password Fail It operates Alarm when wrong User or Admin password input. WRS Reg. Fail It operates Alarm when disconnection of WRS. 5.6.3.2. Alarm Method Setup It is to set ON/OFF of Alarm when system alarm is occurred. Warning Message When setup this menu, it display warning message through pop-up. Warning Message remains On always.. Beep When set this menu, it sounds Beep. Send E-Mail When this menu is sest, it sends email to the address input.
5.7. Monitor Setup It sets the monitor for the display of video from monitor 1 to 4. Available meni for monitor 1~4 are all same. Alarm Pop-up (sec) It sets auto Pop-up display for the alarm. Pop-up display time can be set from 5~10 second. If it sets to “Keep”, it keeps to display Pop-up image and press any button to release Keep mode. Seq. Switching (sec) It sets auto switching from 1 to 60 seconds. Anti-Flicker OSD It can On/Off Anti-Flicker OSD menu.
User Sequence Configuration It can edit Auto transmit function for user mode. 1. It can define all 16 user mode. 2. The picture for example defines 6 Sequences in order as shown 4 division(1,2,3,4) Æ Full mode(1) Æ 4 divisions(5,6,7,8) Æ Full mode(5) Æ Full mode(8) Æ 9 divisions(9,10,11,12,13,14,15,16). 5.8. System Setup 5.8.1. Audio Setup MD1600H supports 4channel Audio recording. But it operates with any channel when video playback. Recording It sets whether Audio records or not.
5.8.2. Time Schedule Setup It sets the time period from Week & Weekend, Day and Night. Weekday Start/End Using Left, Right key sets the time period from Weekday. Other unassigned time is for the Weekend. Day Start/End Using Up, Down button sets Day time period. Other time is applicable to the Night time.
5.8.3. Special Time It can set another specific time zone in each time zone (Week day, Week night, Weekend day and night), For example, various conditions setting separately such as mealtime or meeting time is applicable. It used for the set of regular exceptial time. Max. 4 different specific time can set. Exception Days It used for the setup of irregular exceptional time, max. 30 time zones. - Start Date&Time : Set Starting time. - Duration : Set an interval of Exceptional time.
5.8.4. Security Setup 5.8.4.1. Local Password User Password It is only capable of monitoring and playback only with user registery. Default set is “1111”. Admin Password Authorized administrator can control every function. Default set is “9999”.
5.8.4.2. Remote Users Admin ID setup Admin ID “admin” cannot be changed. Password of admin is set and has all rights and unchangeable. User ID setup Max. 10 user’s ID can be set. To register the user, change Use’s value to “Y” and input ID & password. Basic value is available for all monitoring/playback/Relay.
5.8.5. Disk Setup Auto Deletion When no HDD space left for recording, it deletes the recorded data automatically. Backup Reminder This menu is to inform backup time by everyday, every week, every month. Day/Date/Time It applies the value of setup differently according to value of “Backup Reminder”. Block PlayBack This menu is to playback the recorded images from HDD in limited time. It can set from Day 1 to 31.
5.8.6. Network Setup There are 5 Sub menus. ; Network, xDSL, WRS, Port Setting, NTP Setting 5.8.6.1. Network When TritonHD connects to network, it is to set relevant network information. Type It sets the type (Ethernet/xDSL) of network line connected to TritonHD. It sets ‘Ethernet’ at the connection of network through leased line, Cable model or LAN based connection. It sets to ‘xDSL’ when TritonHD is connected to xDSL line of PPPoE method.
‘DHCP’ is used in LAN that DHCP server works. Nornally, in mid or large scale, it operates DHCP server via LAN but generally use NAT (Network Address Translation) function via HUB in small. IP Address, NetMask, and Gateway Address, DNS, Port, Bandwidth limit It sets IP address, Network Mask, Broadcast address, Gateway , DNS address, and Port, Bandwidth limit. 5.8.6.2. xDSL When TritonHD is with xDSL line and PPPoE method, ID & Password should be setup.
5.8.6.3. WRS If TritonHD is connected to Cable modem or xDSL modem, IP address is changed at every connection to ISP. In this case, changed IP address can not be known. If TritonHD using static IP register into WRS server, changed IP address can be known easily when it connects to TritonHD. To register Static IP to WRS, please refer the following to set. WRS Interval For continuous registery, register inverval should be set to ‘WRS Interval’.
1. If domain address such as 210.116.114.37 or mycam.to is input in WRS URL, DNS server IP should be noted on “System Æ Network Æ DNS1”. 2. DHCP line such as Cable/DSL receives DNS address automatically and does not require an entry. Group ID Group ID is to set group name that TritonHD registered. It recommends uneasy Group name to avoid same Group name registered. Status It indicates the status of TritonHD registry.
5.8.6.4. NTP Setting NTP(Network Time Protocol) synchronizes the time of every devices connected to network. It consists of Server that offers standard time on network, and Client for synchronization that receives the time from server connected. Sync With NTP It can On/Off NTP function. NTP Mode It sets NTP mode of TritonHD operating in Client or both. NTP Server Loc. It enables when NTP Mode is set to Client. It sests whether NTP server is in Local Network or Internet(Public).
Interval (min) It sets interval (min.) of Time synchronization. When NTP Mode is Client, Sync with NTP must be set to On. 5.8.7. Serial Setup MD1600H can set all 4 COM port. Device Set external device connected. Interface This menu is to set which interface can use among RS485 from “RS485” menu. COM1, COM3 is fixed to RS232 and COM2, COM4 is fixed to RS485. Baud rate/Parity/Stop (bit)/Data (bit) In put suitable value according to external device.
5.8.8. Status Overview It shows status & temperature of HDD relevant to video recording and Fan speed. Earliest / Latest Recording It shows intial starting time and last time of the recorded file. Disk Capacity It shows total HDD capacity installed. Used Space It shows HDD capacity recordable. HDD Temp It shows HDD temperature installed. HDD SMART It indicated HDD status installed in GOOD & BAD.
FAN RPM It shows FAN speed installed in TritonHD. 5.8.9. Miscellaneous - After press [MENU] button, move to “Miscellaneous” inferior to “System”. Remote Control ID Max 16 controller ID can set up and contril via 1 remote controller. Set to Off if it is not used. - Face Remote controller toward TritonHD. - Press “ID” button on controller when TritonHD is responding.
Keyboard Control Addr This menu is to set Keyboard address when all functions of TritonHD is controllered by Keyboard button. Default value is set to “1”. If several TritonHDs connect to a keyboard, 32 channel can clash. Then set to the other address of keyboard. DVR ID This menu is set the name of TritonHD. Record No Video If this is “On”, it records video image which is not input. Interpolation Interpolation On/Off The “Interpolation mode” only runs when the recording resolution is in Full D1.
5.9. Disk Manager (Utility) It explains adding or formatting internal, external Hard disk. TritonHD supports various external storage. < Order of Button input> - After press [MENU] button, move to “Utility” inferior to “System”.
5.9.1. Disk Manager Installed Hard disk is automatically recognized. Select Disk Select disk to set. Action Select wanted work among the menus, “Add/Remove/ Confirm Removed/Add used”. [Add] : Add Disk. Use disk that there is no partion table. Partion table can be removed from PC. When adding HDD, “Alarm Partition” menu is activated to set up. “Alarm Partition” indicates dividing 1 HDD to Recording part and Alarm Recording part. [Remove] : Remove present HDD used logically.
without deleting data through Add Used. FAT32 Format FAT32 Format when connecting external Hard disk. Execute FAT32 Format for Backup/Copy in partition of under 250GB. For execution of FAT32 format, creat partition through disk manager of PC first. If HDD size is over 250GB, create several partitions smaller than 250GB and execute FAT32 formate in each partition. Type Followings indicate the type of HDD. [R] : It is recordable by completion of HDD format.
5.9.2. USB Utility It supports firmware upgrading and setup saving & sending, Text file saving for printing set value through USB. Update F/W After saving upgrade firmware for USB use to USB device, connect TritonHD and press ‘Update F/W’ for firmware upgrading. Upgrade firmware for USB use is supplied in “~.date” file. Print Settings(.txt) Function to save Set value for printing into USB device in Text file. Saved data file can be opend through Text editor like Notepad to print and check set value saved.
Load Settings Set the system as set value saved in USB device. Save Settings Save present set value to USB device.
Extension 6. External device connection External device connection is based on the standard of MD1600H 6.1. Using Text device There are 4 essential setups to use Text devices; Text menu, RS232 menu of Serial Setup, Alarm Rec. menu, Recording menu. 6.1.1. Setup in Text Set Recording & Monitoring menu to all ‘On’ and set Sync channel to the wanted value. If connectable devuce is Star Finger 007, set the relevant device only. And et other products to Manual and set all inferior menus.
6.1.2. Setup in RS232 menu of Serial Setup Set connectable device in COM1 of Serial Setup menu, and also set Baud Rate, Parity, Stop, Data with relevant value.
6.1.3. Setup in Alarm Rec If there is video channel want to record with Text sync., set Text Event from Off to On.
6.1.4. Setup in Recording If any channel like to record with Text, set Alarm recording to ‘On’. Full Time is to set all Week day & night, Weekend day & night, and change menu to set Weekday and Weekend differently. < Attention > Every pressing ‘Help’ button, it differ the step of showing video data. Default value at Monitoring shows channel number only. And whenever pressing ‘Help’, it changes to channel name & text sign stage, event status sign, HDD status sign.
6.2. Using Keyboard There are 2 essential setups to use Keyboard; RS232 menu of Serial Setup, PTZ menu of Serial Setup 6.2.1. Setup in COM1 menu of Serial Setup Set connectable device in RS232 in Serial Setup menu to Keyboard. Also set Baud Rate, Parity, Stop, Data with relevant value. 6.2.2. Setup in PTZ menu of Serial Setup Set communication between TritonHD and camera to control via Keyboard & other devices. Inquire to seller for the detailed information about Setup with other products.
APPENDIX APPENDIX APPENDIX 81
#1. Technical Specifications General CPU 32bit RISC Processor Flash memory 32MB Main memory 256MB OS Embedded LINUX Video channel 16Ch. analog video inputs via BNC connector NTSC or PAL video format are supported (Auto detect) Storage device Int.: 4 HDD bays including 2 hot swap-bay Ext: 2 IEEE 1394b (FireWire) connection ports* 2 eSATA connection ports 1 Network Storage port (RJ45)* Supports Disk management tool for all disks.
Schedule recording Daily : Day / Night / Four-segment time frame Weekly : Weekdays / Weekends, Exception days Conditions : Normal / Event Text Data recording POS/ATM transaction information archived along corresponding video data Manual recording Manual(Emergency) record triggered by font key Audio Recording & Playback Recording level -7~8 (16 step) recording level Monitoring Support remote monitoring and two way audio Network Program Control Center Lite-D (Bundle) Support Control Center seri
Environment Operation temperature 5 ~ 45℃ Storage temperature -10 ~ 55℃ Operation humidity 30~80%, free of condensation Storage humidity 93% below, free of condensation Data Backup/Expansion/Copy Data backup External HDD(via 1394b or eSATA) Internal CD-R/DVD-R Backup reminder 5~ 95% alarm AVI Copy External USB memory disk(USB 1.
Power consumption Max. 85W Typical 60W Mechanical Dimension (WⅹDⅹH) 430.0 x 362.0 x 88.0 Weight 5.
#2. Utilizing IP address in Local network #2.1. Outline When internet uses, it connects to another server for acquisition of data or email communication through IP address. So it is not connectable to Internet without IP address. At present, authorized IP has limits to use in worldwide. And there are 5 grades from A to E in network that possesses many IP. Most common used network is C grade network. #2.2.
IP address : 3 numbers in X4 indicates Host ID that is addressed from 0 to 255. But, generally, 0 & 255 is used to network ID & Broadcast address, but 1 to 244 IP address used in practical. Network ID: As Local network ID, the address indicates network identity in Internet. Generally, it addresses most superior number in local network. Gateway address: It is IP address for Router connecting internet and local network, and the path of connecting local network that is ID assigned ID and internet.
(2) When structure 2 networks in same size (1/2 + 1/2), Sub-Network ID: xxx.xxx.xxx.0 Gateway Address: xxx.xxx.xxx.1 Subnet Mask: 255.255.255.128 Broadcast Address: xxx.xxx.xxx.127 IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.126 Sub-Network ID: xxx.xxx.xxx.128 Gateway Address: xxx.xxx.xxx.129 Subnet Mask: 255.255.255.128 Broadcast Address: xxx.xxx.xxx.255 IP Addresses: xxx.xxx.xxx.130 – xxx.xxx.xxx.254 (3) When structure 3 networks (1/2 + 1/4 + 1/4) Sub-Network ID: xxx.xxx.xxx.0 Gateway Address: xxx.xxx.xxx.
(4) When structure 4 networks (1/4 + 1/4 + 1/4+1/4) Sub-Network ID: xxx.xxx.xxx.0 Gateway Address: xxx.xxx.xxx.1 Subnet Mask: 255.255.255.192 Broadcast Address: xxx.xxx.xxx.63 IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.62 Sub-Network ID: xxx.xxx.xxx.64 Gateway Address: xxx.xxx.xxx.65 Subnet Mask: 255.255.255.192 Broadcast Address: xxx.xxx.xxx.127 IP Addresses: xxx.xxx.xxx.66 – xxx.xxx.xxx.126 Sub-Network ID: xxx.xxx.xxx.128 Gateway Address: xxx.xxx.xxx.129 Subnet Mask: 255.255.255.192 Broadcast Address: xxx.
A1webcams, Inc. 3525 East Enterprise Drive Anaheim, CA 92807 Tel : (714) 688-7986 Fax : (714) 688-7989 Email: Salesteam@a1webcams.com Website: www.A1webcams.com The contents of this manual can be modified in accordance with Firmware or Software upgrade.
