enUS USER GUIDE
TABLE OF CONTENTS Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SPIRIT II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Box Contents Battery Pack + AA AA + AA AA Batteries (3) + Battery Pack Bracket Battery Wire LP Magnet Wire Retention Clip LP Fuel Sensor iGRILL 3 Yellow Coloured Probe Indicator Meat Probe Probe Wrap Red Coloured Probe Indicator Probe Wrap Meat Probe WARNING! Probe gets hot. Use mitts.
Installation 1 Remove cover plate. Some models may have screws.
Installation 2 2 AA AA Install batteries. Do not mix old and new batteries. Do not mix alkaline, standard or AA rechargeable batteries.
Installation 3 3a Install bracket on the inside of the wheel frame. Snap battery pack into bracket. Connect battery wire to the battery pack.
Installation 3b Route battery wire through front of side table. Connect battery wire to the iGRILL.
4 Installation 4a Install magnet.
Installation 4b Connect LP fuel sensor.
Installation 5 5 Snaps into place. No screws required.
Installation 6 6 Remove adhesive liner from wire retention clip. Apply clip to cleansed area underneath side table. Wire(s) must be secured using clip.
1 Installation 1 Remove cover plate.
Installation Remove LED fuel gauge.
Installation 2 2 AA AA Install batteries. Do not mix old and new batteries. Do not mix alkaline, standard or AA rechargeable batteries.
3 Installation 3 Install bracket underneath side table.
4 Installation 4 Connect the battery wire to the battery pack. Then, snap the battery pack into the bracket.
Installation 5 5 Route battery wire through front of side table. Connect battery wire to the iGRILL.
Installation 6a Install magnet on GENESIS II models. GENESIS II LX models already have magnet installed.
Installation 6b Connect LP fuel sensor.
7 Installation 7 Connect lighted control knob wires. Installation on GENESIS II LX only.
Installation 8 8 Snaps into place. No screws required.
Installation 9 9 Remove adhesive liner from wire retention clip. Apply clip to cleansed area underneath side table. Black wire(s) must be secured using clip.
Quick Start Instructions 1 WEBER iGRILL App Download the WEBER iGRILL App. Then enable Bluetooth® on your smart device under ‘Settings’.
Quick Start Instructions 2 Press the power button once to turn on the iGRILL 3. A single beep will sound.
Quick Start Instructions 3 Open the door on the front of the iGRILL 3 to expose the probe ports.
Quick Start Instructions 4 Plug one or more probes into the ports. WARNING: Risk of burns! Handling the meat probes without hand protection will result in severe burns. Please wear heat-resistant gloves or mitts at all times while using this product in order to avoid being burned.
Quick Start Instructions 5 Launch the WEBER iGRILL App on your smart device. Follow the pairing instructions within the app. You are now ready to use your iGRILL 3. Additional information, instructional videos and barbecue inspiration can be found at weber.com/igrillsupport.
Important Information Visit weber.com/igrillsupport to find out more about device compatibility, languages supported by the WEBER iGRILL App, a full user guide with instructional set up videos, and great barbecuing inspiration. Please read the full user guide – especially the safety information – before using the WEBER iGRILL 3 for the first time, and follow the instructions while using the device.
Disposal Requirements WARNING: Battery disposal! Never dispose of batteries in an open fire. Always dispose of batteries in accordance with local laws. Technical Specifications Frequency Range (MHz): 2402.0 - 2480.0 MHz Output Power (Watts): 0.0012 W FCC Compliance This equipment has been tested and found to comply with the rules for white space devices, pursuant to part 15 of the FCC rules. These rules are designed to provide reasonable protection against harmful interference.
Importado y Distribuido en México por: Weber-Stephen Products S.A. de C.V. ANATOLE FRANCE 139-139A Colonia. POLANCO III SECCION Del. MIGUEL HIDALGO CIUDAD DE MEXICO C.P. 11540 RFC: WPR030919-ND4 Teléfono: 01800-00-WEBER (93237) Imported by / importé par WEBER-STEPHEN (CANADA) COMPANY 1 Roybridge Gate Vaughan, Ontario, CANADA L4H 4E6 The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Weber-Stephen Products LLC is under licence.
