Instruction Manual

ManualsBrandsWebDT ManualsPDAsDT307SC

DT307SC/ DT307SC-MD

ENGLISH

Mobile POS Tablet

BASIC OPERATION GUIDE

DT307SC/ DT307SC-MD

ENGLISH

signage dtri com

DT Research, Inc.

2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com

DT Research and WebDT are registered trademarks or trademarks of DT Research, Inc.

BOG070814DT307SC/ DT307SC-MDENG

INTRODUCTION

Thank you for acquiring the DT307SC/ DT307SC-MD Mobile Tablet. The DT307SC/

DT307SC-MD oﬀers a 7

”

capacive touch display in a comp

act, rugged, and lightweight

package. The DT307SC/ DT307SC-MD enables eﬃcient point-of-service/sales applicaons,

inventory management, and ﬁeld services.

The DT307SC/ DT307SC-MD provides the precise features needed to streamline

operaons and improve producvity, data accuracy, and service.

PACKAGE CONTENTS

One DT307SC/ DT307SC-MD •

One baery pack and Handstrap•

Capacive Touch Stylus and Lanyard•

AC-DC power adapter•

Basic Operaon Guide•

*The actual package contents may vary depending on the conﬁguraon acquired.

PRECAUTIONS

Always exercise care when operang and handling the DT307SC/ DT307SC-MD.•

Do not disassemble any poron of the DT307SC/ DT307SC-MD, as this will void any •

product warranty.

Do not use any power adapter or charging cradle other than the one provided with •

the tablet or acquired from the manufacturer or its partners.

In the unlikely event that abnormal noise, strange odor, or smoke is present, imme-•

diately power down the DT307SC/ DT307SC-MD and disconnect all power sources.

Please report the problem to your device provider immediately.

MODIFY THE READING RESULT FOR SCANNER/ RFID/ MSR

Adjust the data capture module reading result:

Launch 1. Keyboard Wedge menu from taskbar

Go to 2. Conﬁguraon

CAMERA UTILITY

Capture Picture/Video:

Launch the 1. Camera Ulity from Start > Camera

Select the picture mode by pressing 2. Screenshot or Video buon

For other advanced sengs, please select the 3. sengs to modify from Browser/

Resoluon/Flashl

ight or other Properes for the ﬁle captured

ADVANCED SETTINGs - MSR

Enable/disable MSR module, and setup the Parse Data Format for MSR:

Launch 1. Keyboard Wedge menu from taskbar

Go to 2. Conﬁgure MSR

Select 3. Enable to setup the conﬁguraon

NOTE: Unless you are sure you need to enable parse, we recommend you do not

use this seng.

Summary of content (2 pages)

PAGE 1
DT307SC/ DT307SC-MD Mobile POS Tablet ADVANCED SETTINGs - MSR Enable/disable MSR module, and setup the Parse Data Format for MSR: 1. Launch Keyboard Wedge menu from taskbar 2. Go to Conﬁgure MSR 3. Select Enable to setup the conﬁguration DT307SC/ DT307SC-MD BASIC OPERATION GUIDE ENGLISH INTRODUCTION NOTE: Unless you are sure you need to enable parse, we recommend you do not use this setting.
PAGE 2
DT307SC/ DT307SC-MD DT307SC/ DT307SC-MD I/O Ports Data Capture Module Operation Guide DT307SC Front View If your DT307SC/ DT307SC-MD comes with a data capture module(s), you may refer the content below to conﬁgure the settings. DT307SC-MD Front View BASIC MODULE OPERATION A A DT307SC/ DT307SC-MD Rear View B C D 3 steps to capture the data results from Keyboard Wedge: 1. 2. 3. 4.