TI-810+ Motherboard Note to Users This User’s Guide & Technical Reference are for assisting system manufacturers and end users in setting up and installing the motherboard. Every effort has been made to ensure that the information in this manual is accurate. Weal Union Development Limited is not responsible for printing or clerical errors. Information in this document is subject to change without notice and does not represent a commitment on the part of Weal Union.
TI-810+ Motherboard Table of Contents Chapter 1 Introduction...........................................................3 1.1 Product Features ..................................................................................... 3 1.2 Full Software Configurable .................................................................... 3 1.3 Features Summary ................................................................................... 4 Chapter 2 Installation.................................................
TI-810+ Motherboard Chapter 1 Introduction 1.1 Product Features The TI-810+ highest performance motherboard is based on the all new Intel 810 chipset with Baby AT form factor to support the latest Socket 370 including Intel Pentium III FCPGA, Celeron FCPGA / PPGA as well as Cyrix III processors. This chipset incorporates with AGP 3D Graphics Support and an optional Crystal AC97 Audio. This motherboard is also fully software configurable via AMI BIOS setup and supports high-speed UDMA/66 IDE devices.
TI-810+ Motherboard 1.
TI-810+ Motherboard Chapter 2 Installation 2.1 Installation Instructions This section covers External Connectors and Memory Configuration. Please refer to the motherboard layout chart for external connectors, slots and I/O ports. Furthermore, this section lists all necessary connector pin assignments for your reference. The locations of the connectors and ports are illustrated in the following figures. Before inserting these connectors, please pay attention to the orientations. NOTICE !!! 1.
TI-810+ Motherboard 2.3 Function & Installation Instructions 2.3.1 AT Power Supply Connector (12-Pin) Blue Yellow Red Orange Black White Red This connector connects to a standard 5V power supply. To connect the leads from the power supply, ensure first that the power supply is not power on. Most power supplies provide two plugs, and each plug contains six wires. Two of six wires are black and please orient the plugs to the connector so that 4 black wires are together.
TI-810+ Motherboard 2.3.3 AT Keyboard Connector This connector supports a standard IBM-compatible keyboard, such as 101/102 enhanced keyboard (Use a PS/2 keyboard adapter in order to connect a PS/2 KB to this AT connector.). 2.3.4 Serial (COM1/COM2) Port Connector This motherboard provides two compatible serial ports, it can be used when add additional serial devices. 2.3.5 Parallel Port Connector (26-pin) This connector supports the included parallel port ribbon cable with mounting bracket. 2.3.
TI-810+ Motherboard EXPANSION CARDS INSTALLATION 1. 2. 3. 4. 5. Before adding or removing any expansion cards or system components, confirm that you already unplugged your power supply. Otherwise, it may severely damage to your motherboard and expansion cards. Please follow the installation procedures as below: Check carefully if those hardware or software settings for your expansion cards are in the proper position as shown in their User’ s Manual.
TI-810+ Motherboard If you install two IDE devices on the same cable, you must configure the second device to slave mode by setting its jumper accordingly. (Refer to your IDE device document for the jumper settings. Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged.) Primary IDE (IDE1) Secondary IDE (IDE2) Pin1 Pin20 be removed IDE Connectors 2.3.
TI-810+ Motherboard 2.3.15 PGA370S CPU Socket The motherboard provides a ZIF Socket 370. The CPU that comes with the motherboard should have a fan attached to it to prevent overheating. If it is not so, purchase a fan before you turn on your system. Notice!!! Be sure that there is a sufficient air circulation across the processor’ s heatsink by regularly checking that your CPU fan is working.
TI-810+ Motherboard 2.3.18 Internal Audio Connectors(CD, AUX, 4-pin Modem) These connectors allow you to receive stereo audio input from such sound sources as a CD-ROM, MPEG card. The Modem connector allows the onboard audio to interface with an voice modem card with a similar connector. It also allows the sharing of mono_in (such as a phone) and mono_out(such as a speaker) between the onboard audio and the voice modem card.
TI-810+ Motherboard Chapter 4 AMIBIOS Setup This TI-810+ motherboard comes with the AMI BIOS from AMI Software Inc. Enter the AMI BIOS program Main Menu by: 1. Turn on or reboot the system. After a series of diagnostic checks, the following message will appear: Press to enter setup, ESC to skip memory test 2. Press the key and the main program screen will appear as follows. A M I B I O S H I F L E X S E T U P U T I L I T Y - V E R S I O N 1 . 21 (C)1998 American Megatrends, Inc.
TI-810+ Motherboard 3. Using the arrows on your keyboard, select an option, and press . Modify the system parameters to reflect the options installed in your system. Otherwise you may return to the Main Menu anytime by pressing . Types of Setup Description Standard CMOS Setup Sets time, date, hard disk type, types of floppy drives, monitor type, and if keyboard is installed.
TI-810+ Motherboard AMIBIOS SETUP - STANDARD CMOS SETUP (C)1998 American Megatrends, Inc. All Rights Reserved Date (mm/dd/yyyy) : Mon Sep 25, 2000 Time (hh/mm/ss) : 17:05:08 Floppy Drive A: Floppy Drive B: Pri Master Pri Slave Sec Master Sec Slave : : : : Base Memory: 0 KB Extd Memory: 0 MB 1.
TI-810+ Motherboard Type How to Configure SCSI Select Type. Select Not Installed the drive parameter screen. The SCSI drivers provided by the SCSI manufacturer should allow you to configure the SCSI drive. IDE Select Type. Select Auto to let AMIBIOS determine the parameters. Click on OK when AMIBIOS displays the drive parameters. Select LBA/Large Mode. Select On if the drive has a capacity greater than 540 MB. Select Block Mode. Select On to allow block mode data transfers. Select 32-Bit Transfer.
TI-810+ Motherboard 4.2 Advanced CMOS Setup The AMIBIOS Setup options described in this section are selected by choosing Advanced CMOS Setup from the AMIBIOS Setup main menu. 4.3 Advanced Chipset Setup Choose Chipset Setup on the AMIBIOS Setup main menu. All Chipset Setup options are then displayed. AMIBIOS Setup can be customized. 4.4 Power Management Setup The AMIBIOS Setup options described in this section are selected by choosing Power Management Setup from the AMIBIOS Setup main menu. 4.
