WayteQ GPS MID n800 User Manual Version 1.1 Precaution and Notice The PND is used only as a navigation aid. It is not for precise measurement of direction, distance, location or topography. The user must follow all traffic signs and local regulations along the roads. GPS satellite signals cannot pass through solid materials (except glass). When you are inside a tunnel or building, GPS position is not available. A minimum of 4 GPS satellite signals are needed to determine current location.
significantly. Please copy system data to external storage devices when update system data. WayteQ Technologies is not responsible for system data corruption or loss. GPS Maintenace Please use stylus to tap and operate the navigator, never press the touch screen forcefully. Please use soft cloth with little glass cleaning agent to clean the screen. Never clean the touch screen without shutting down the GPS navigator. Droping or bump may cause damage of precision parts , such as LCD Screen, etc.
A. Indication Light B. Power C. SD Card slot D. Mini USB E. Speaker F. MIC hole G. Reset H. Earphone Jack Once the card is installed, it cannot be removed during the operation of the device. If you need to remove the card, switch the unit off first, push the card in and it will eject from the slot. 1.2 Power Supply N800 navigator uses built-in, irreplaceable Li-Polymer battery as power supply , battery icon “ “on the main menu indicates current remaining power.
Please charge the device for more than 1 hour by AC adapter when you use the device for the first time. Please charge the device in time when low battery or battery depletion. Please keep the device in a cool and dry place with more than half of battery capacity when not use the device for a long time. 1.4 Charging by Car Charger Caution: To protect your device against suddenness, please connect the car charger only after the car engine has been started. 1.
Tap the “Cancel” button to turn back to the screen. 2. Reset System When system un-responses , please press the RESET key to restart the system. The below list may contribute to the system un-response: - Screen duration or stagnation resulting in screen switching unsuccessfully; - More time spent on taping and not active; - Starting up or shutting down the device unsuccessfully when pressing the power button Notice: Pressing the RESET key will cause the unsaved system info loss. Please keep data backup .
Tapping “turn on”: turn on Wi-Fi module Tapping “turn off”: turn off Wi-Fi module Choose and tap the available network, then tap “advance” icon, you can set the network as below interface : Tap “IP setting” icon, you can set the network address (interface as below). Select Auto or Manual for network setting. Input password, tap “ connect ” to connect the network; tap “disconnect” for disconnecting the network. After network connection successfully, then you can log on and surf the internet.
Tap “ “ to choose hiding or showing the soft keypad , you can input web address by the keypad . Tap” “ to return to home page . Tap” “ to enter into favorite list interface as below : Tap” ” to add new favorite web site . Double click the website name , and enter into below interface , you can connect this website directly , edit website or delete this website in the favorite list .
Tap” “ to view history website . Tap” “ to enter into Setting interface : You can set “ Home Page “ , “ Text Size “ and “ Encoding “ . Tap “ Memory “ , you can clear web view history . Tap” Security “, you can choose “ Cookies “ setting . 5. Bluetooth Tap one of the " Bluetooth " icons on the main menu , enter into Bluetooth interface as follow , The bottom is the connection status bar:.
Tap the “ Device list ” icon and enter into the following interface : Tap the “ ” icon to connect the chosen device , tap the “ “ to disconnect , tap the “ “ to delete pair info . If paired mobile phone not in the device list, please tap the “ “ icon and enter into searching interface and pair with mobile phone ( mobile phone’s Bluetooth should be power on and near the PND ).
If incoming call , the interface as below .
Tap the “ “ icon and enter into Bluetooth setting interface as below. Name : display name of the device in the process of the Bluetooth transmission . Pin: Tap the icon “ “ and enter into pin code interface . Optional Bluetooth Value Added Functions Dial-Up Network ( DUN ) Notice: The paired mobile phone must support GPRS function. Tap the “ Device List ” icon and enter into the below interface.
Double tap “Dialup Networking Service” and enter into GPRS setting interface as below: You can choose GSM/GPRS network operator or input network operator name, then tap “connect”. Return to the main menu after connection successfully , and tap the “IExplorer” icon to surf the internet.
Select phone number , and tap “ “ to dial the number . tap the “ 6. Music Tap the icon “Music” on the main menu and enter into the following interface . A. Return to the Media menu B. Volume control C. Select desired music file D. Stop E. Next F. Pause / Play G. Previous H. Speed Bar I. Play mode J. Equalizer Double tap icon “ ” to choose music file . “ to delete the selected number .
Tap the icon “ “ for single selection , tap the icon “ single delete , tap the icon “ ” “ to select all , tap the icon “ “ for to delete all . 7. Photo Tap the "Photo" icon on the media menu and tap the icon “ “ to select photo files , double tap the photo file to see the following interface . A. Return to the Media menu B. Select photo file C. Slide mode D. Rotate E. Zoom in F. Zoom out G. Next H. Previous 8.
8.1 Ebook Tap the "EBook" icon , then tap the " " icon to choose Ebook files , double tap the file and enter into the following interface . A. Return to the Media menu B. Bookmark list C. Bookmark D. Theme and font E. Down F. Up G. Select EBook files 8.2 Flash Player Tap the icon “ Flash ” and enter into the following interface .
A. Volume B. Return to the Media menu C. Select flash file D. Stop E. Play / Pause F. Speed Bar 8.3 GsFinder Tap the icon “ GsFinder ” and enter into the following interface , to manage, view or find files . 9. Video Tap the icon "Video" on the media menu , then tap the “ and enter into following interface .
A. Return to the Media menu B. Volume C. Select video file D. Stop E. Next F. Pause/play G. Previous H. Speed bar Tips: Tap NEXT button to recycle the movie. Double tap the screen, it will display in full screen, double tap the screen again, it will return to original playing size. 10. Toolbox Tap the icon "Toolbox" on the main menu and double tap the tool program to run it . Tap the icon "GPSView" and the device will show the detail information of GPS satellites .
11. Games Tap the icon "Games" on the main menu and double tap the game to run it . 12. Setting Tap the icon "Setting" on the main menu and enter into the following interface .
Tips : after make any changes of setting , tap " " to save the change . 12.1 Volume Tap the icon “Music” on the media menu and enter into the following interface . Choose “ Music “ files to be background sound when unit is power on . 12.2 Backlight Tap the "Backlight" icon and enter into the following interface . Tap “Left-side” or “Right-side” button to select the duration of automatically powering off the backlight. 12.3 Language Tap the "Language" icon and choose the language .
12.4 Date and Time Tap the icon "Date Time" and enter into the following interface to set date , time and time zone . 12.5 Calibration Tap the " Calibration " icon and enter into the following interface . Tap the icon "OK" to adjust the touch screen. 12.6 Factory Reset Tap the " Factory Reset " icon and enter into the following interface . Tap the icon “ OK “ to load factory default setting .
12.7 System Info Tap the "Sys Info" icon and enter into the following display interface . 12.8 USB Tap the icon “USB” to set the USB working mode . 12.9 Nav Path Tap the "Nav Path" icon and enter into the following display interface .
When you have several Navigation maps in the device, if you choose the "Navigation" icon , you can set up one of Navigation maps ( navigation program files ) , and select the Auto Run Navigation , next time when tapping the “GPS” icon on the main menu, the device will run the selected Navigation software automatically . 13. WinCE Tap the icon "WinCE" on the main menu and enter into the following interface .
Internet Explorer to visit website Use Windows Messenger to contact with your friends Enter into WiFi interface Manage files in your device Read PDF files View pictures file Read Windows Word files Read Windows Excel files Read Windows PowerPoint files Notepad Windows Media Player This document is for guidance only and does not form part of any contract, and may be subject to change without notice