User Guide

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,
refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com
hole onto the center stile. Drill 1/16” pilot holes at the marked hole locations. Fasten both lift
handles to the center stile using #10 X 5/8” pan head self tapping screws.
If the door came with two sets of lift handles repeat the same process for the other lift
handles.
Lock section Lock section
(2) #10 X 5/8” Pan
head self tapping
screws
(4) #10 X 5/8” Pan
head self tapping
screws
Center line Center line
Vertical
line
Vertical
line
Lift
handle
Lift
handle
Lift
handle
Center stile
Center
stile
Center stileCenter stile
3-7/8” 3-7/8”
Horizontal
line
Horizontal
line
Lift handles
Bottom section
Typical placement of lift
handles referenced on
single wide doors
Lock
section
Typical placement of lift handles referenced on double wide doors
20” Minimum to
30” Maximum
20” Minimum to 30” Maximum
Pull handle
Lift handles
Bottom
section
Lock
section
Pull handle Pull handle
Pull Handles
Tools: Tape Measure, Pencil, Power Drill, 1/16” Drill Bit
6
Locate and mark the horizontal and vertical center on the bottom rail of the bottom section,
on single car doors.
Center the pull handle using the vertical and horizontal lines as referenced on the bottom
section rail. Using the pull handle as a template, mark the two hole locations in the pull
handle onto the horizontal line of the bottom section rail. Drill 1/16” pilot holes at the marked
hole locations. Fasten pull handle(s) using (2) #10 X 5/8” pan head self tapping screws.
If your door came with two pull handles, locate them directly below the lift handles and
repeat the installation process.
Bottom section
(2) #10 X 5/8” Pan
head self tapping
screws
Bottom rail
Center stile
Pull handle
Lift handles
Bottom section
Typical placement of pull
handle referenced on
single wide doors
Lock
section
Typical placement of pull handles referenced on double wide
20” Minimum to
30” Maximum
20” Minimum to 30” Maximum
Pull handle
Lift handles
Bottom
section
Lock
section
Pull handle Pull handle
Cable Drum Assemblies and Track Rollers
Tools: None
7
NOTE: Refer to door section identification, located in the pre-installation section of this
manual or refer to Parts Breakdown on page 2.
NOTE: Cable drum assemblies are marked right and left hand.
WARNING WARNING
FAILURE TO ENSURE TIGHT FIT OF CABLE LOOP OVER MILFORD PIN COULD
RESULT IN COUNTERBALANCE LIFT CABLE COMING OFF THE PIN, AL-
LOWING THE DOOR TO FALL, POSSIBLY RESULTING IN SEVERE OR FATAL
INJURY.
Uncoil the counterbalance lift cables from the cable drum assemblies, making sure you place
the left hand cable loop on the left hand milford pin of the bottom corner bracket and the
right hand cable loop on the right hand milford pin of the bottom corner bracket.
NOTE: Check to ensure cable loops fits tightly over the milford pins.
Insert a short stem track roller into the bottom corner brackets and another into the #1
graduated end hinges at the top of the bottom section.
NOTE: Larger doors will use long stem track rollers with double graduated end hinges.
NOTE: Verify bottom weather seal is aligned with bottom section. If there is more than 1/2”
excess weather seal on either side, trim weather seal even with bottom section.
Double graduated
end hinge (Hinge
tube)
Long stem
track roller
Counterbalance lift cable
Short stem track roller
#1 Single graduated end hinge
(Hinge tube)
Bottom corner bracket
warning label
Milford pin
Cable loop
Bottom weather seal
Bottom corner
bracket
Left hand cable
drum assembly
Bottom
section
Short stem track roller
7