User Guide

ManualsBrandsWayne-Dalton ManualsDoor6100

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To ﬁnd your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Bottom rail

of horizontal

track

Flag angle

Quick

Install

tab

Key slot

Quick Install

tab in place

Tracks ﬂush

1/4”-20

Flange hex

nut

Top rail of

horizontal

track

1/4”-20 x 9/16”

Track bolt

Washer

Flagangle

Vertical

track

Vertical

track

Horizontal Tracks/F.A. Flag Angles

Tools: Ratchet wrench, 7/16” Socket, 9/16” Socket, 9/16” Wrench,

level, Step ladder, Flat tip screwdriver

NOTE: If you have Fully Adjustable ﬂag angles, complete this step.

To install horizontal track, place the top rail end over the top track roller of the top section.

Align the bottom rail end of the horizontal track with the top of the vertical track. If you have

Quick Install horizontal track, tighten the bottom rail of the horizontal track to the ﬂag angle

with (1) stud plate and (2) 1/4”-20 ﬂange hex nuts. If you have Universal horizontal track,

tighten the bottom rail of the horizontal track to the ﬂag angle with (2) 1/4”-20 x 9/16” track

bolts and (2) 1/4”-20 ﬂange hex nuts.

WARNING WARNING

DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED AT REAR,

AS OUTLINED IN STEP, REAR BACK HANGS, OR DOOR COULD FALL FROM

OVERHEAD POSITION CAUSING SEVERE OR FATAL INJURY.

Level the horizontal track assembly and bolt the top rail of the horizontal track to the encoun-

tered slot in the ﬂag angle using (1) 1/4”-20 x 9/16” track bolt, (1) 1/4”-20 ﬂange hex nut

and (1) 5/16 washer. Repeat for other side.

Remove the nail that was temporarily holding the top section in place, installed in step, Top

Section.

IMPORTANT: FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD

CAUSE PERMANENT DAMAGE TO TOP SECTION.

NOTE: If an idrive

opener will be installed, position horizontal tracks slightly above level.

Bottom rail

Quick Install

Horizontal

track

1/4”-20

Flange hex

nuts

Stud plate

Flag angle

upper slot

1/4”-20 x 9/16” Track bolts

Bottom rail Fully

Adjustable

Horizontal

track

1/4”-20

Flange hex

nuts

Flag angle

upper slot

1/4”-20

Flange hex

nut

Top rail of

horizontal

track

1/4”-20 x 9/16”

Track bolt

Washer

Flagangle

Vertical

track

Vertical

track

Adjusting Top Fixtures

Tools: 7/16” Wrench, Step ladder

With horizontal tracks installed, you can now adjust the LHR top brackets.

NOTE: Depending on your application, you may need to reverse the top bracket slide for

more adjustment, if needed, prior to securing it to the top bracket base.

TO ADJUST THE TOP BRACKET SLIDES: Loosen the (2) 1/4”-20 ﬂange hex nuts (if neces-

sary) and vertically align the top section of the door with the lower sections. Once aligned,

position the top bracket slide, out against the horizontal track. Maintaining the slide’s posi-

tion, tighten the (2) 1/4”-20 ﬂange hex nuts to secure the top bracket slide to the top bracket

base. Repeat for other side.

TO REVERSE THE TOP BRACKET SLIDES (IF NEEDED): Remove the two 1/4” - 20 x 5/8”

carriage bolts, two retention washers and two 1/4” - 20 ﬂanged hex nuts. Flip the top bracket

slide in the opposite direction. Loosely fasten the top bracket slide to the bracket using two

1/4” - 20 x 5/8” carriage bolts, two retention washers and two 1/4” - 20 ﬂanged hex nuts,

as shown.

NOTE: The retention washers must be fully seated against the top bracket base to ensure the

anti-twist feature on the top bracket slide engages in the slotted hole in the top bracket base.

(2) 1/4” - 20

Flange hex nuts

Top section

Low headroom

horizontal track

Roller

Top bracket

assembly

Top bracket

slide

(2) 1/4” - 20

Flange hex nuts

(2) Retention washers