OWNER’S MANUAL SLIDING POT ORGANIZER
PARTS LIST Your Sliding Pot Organizer should include the following parts. Please inspect box contents to ensure you have received all components. If you are missing any parts, need assistance with assembly or have questions, please contact our Customer Service. Parts can also be requested online at our customer center You will need a Phillips screwdriver for assembly. A rubber mallet is also recommended.
INSTALLATION INSTRUCTIONS – In Cabinet STEP 1 Cabinet must be at least 20”W x 20”D. G (1) Place CABINET MOUNTING TEMPLATE (G) inside your cabinet. Using a pencil, mark the location where you plan to install the CABINET SCREWS (F). • To ease installation you can pre-drill small holes at the marked locations. STEP 2 Identify LEFT (B) and RIGHT (C) SLIDES. • Note that the BACK end of each SLIDE (B & C) has a black tip and the FRONT end does NOT.
INSTALLATION INSTRUCTIONS – In Cabinet STEP 3 Align POT ORGANIZER (A) at the marked location and push it into the Clips of the LEFT (B) RIGHT (C) SLIDES A (1) Installation Suggestion: With the POT ORGANIZER (A) resting on top of the Clips, brace the top of the POT ORGANIZER (A) with one hand and, with a rubber mallet, lightly tap each bottom corner of the POT ORGANIZER (A) to secure the POT ORGANIZER (A) into the Clips.
INSTALLATION INSTRUCTIONS – On Wire Rack STEP 1 The wire shelf needs to be a minimum of 20” in depth. Identify the LEFT (B) & RIGHT (C) SLIDES. • Note that the BACK end of each SLIDE (B & C) has a black tip and the FRONT end does NOT. B (1) C (1) Place SLIDES (B & C) on desired wire shelf. Make sure the FRONT of the SLIDES (B & C) are lined up with the FRONT of the shelf. Line up the slides along the wires in the wire shelf to ensure they are straight.
INSTALLATION INSTRUCTIONS – On Wire Rack STEP 3 With a Phillips screwdriver, secure the SLIDES (B & C) to the wire shelf by putting PLATE SCREWS (E) through the slots and fasten to the RACK PLATES (D). Note: RACK PLATES (D) need to be installed from the underside of the shelf. D (4) E (4) STEP 4 Attach the POT ORGANIZER (A) to the Clips in the LEFT (B) and RIGHT (C) SLIDES until it clicks into the Clip.
USAGE INSTRUCTIONS DIVIDER PLACEMENT SHORT (H) and TALL (I) DIVIDERS can be installed in either orientation shown below or a combination according to your needs. DIVIDER INSTALLATION To install the SHORT (H) and TALL (I) DIVIDER first clip in one side of the DIVIDER (H) & (I). Then flex the SHORT (H) or TALL (I) DIVIDER and clip in the other side.
SERVICE PARTS LIST Customer Service provides the following replacement parts: Description 1)Tall Divider 2)Short Divider 3)Pot Organizer 4)Right Slide 5)Cabinet Screw 6)Template 7)Plate Screw 8)Rack Plate 9)Left Slide 1 2 9 3 4 7 8 5 7 6
WARNINGS 1. Read and understand all instructions. Failure to follow all instructions may result in injury and/or damage. 2. The warnings, cautions, and instructions discussed in this manual cannot cover all possible conditions or situations that may occur. The user must always be aware of their environment and ensure that they use the product in a safe and responsible manner. 3. Do NOT modify the product in any way.
PRODUCT REGISTRATION Thank you for purchasing a Sliding Pot Organizer. In order to register your product and receive streamlined customer service, please fill out the following Product Registration Form and (1) fax the form (2) complete the Product Registration Form online or (3) scan and email the form. Include a copy of your original receipt with your submission.
1 YEAR LIMITED WARRANTY Sliding Pot Organizer We warrant to the original consumer purchaser (“Purchaser”) of the Sliding Pot Organizer (“Product”) that each Product shall be free from defects in workmanship and materials for a period of 1 year from the date of original purchase.
CONTACT US QUESTIONS? NEED PARTS? WE ARE HERE TO HELP! Please feel free to contact us. There are no questions too small, or any problems too big. We’re committed to providing our customers with the highest level of service.
