WISMO Quik Q2400 series Q2403 Product Specification Reference: WM_PRJ_Q2400_PTS_001 Revision: 003 Date: 6th November 2002 Page : 1 / 70 confidential © This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Document Information Revision 001 Date Sept 2001 002 July 2002 003 November 2002 History of the evolution Creation as “Preliminary” “Preliminary” mention removed but GPRS consumption is still TBD IMP connector removed from the PTS GPRS consumption confirmed (§ 2.2.2) Physical characteristics confirmed (§ 3.3.1) Page : 2 / 70 confidential © This document is the sole and exclusive property of WAVECOM.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Overview This document defines and specifies the WISMO QUIK Q2403 Series, available under two GSM/GPRS Cl.2 versions: • Q2403A: EGSM/GPRS 900/1800 MHz version with 16 Mb of Flash memory and 2 Mb of SRAM (16/2) • Q2403B: EGSM/GPRS 900/1800 MHz version with 32 Mb of Flash memory and 4 Mb of SRAM (32/4) Page : 3 / 70 confidential © This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Contents Document Information......................................................................... 2 Overview ............................................................................................. 3 Contents.............................................................................................. 4 Caution................................................................................................ 7 Trademarks ..................................
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.11 Audio interface ......................................................................................22 2.11.1 Common microphone inputs characteristics ..................................23 2.11.2 Common speaker outputs characteristics ......................................24 2.11.2.1.1 Differential Connection.......................................................24 2.11.2.2 Single-ended Connection .........................................................
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 4 Connectors and peripheral devices references............................ 50 4.1 General Purpose Connector ...................................................................50 4.2 RF footprint ...........................................................................................50 4.3 SIM Card Reader ...................................................................................50 4.4 Microphone ................................................
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Caution Information furnished herein by Wavecom are accurate and reliable. However no responsibility is assumed for its use. Please read carefully the safety precautions for a terminal based on WISMO Quik Q2403 Series. General information about Wavecom and its range of products is available at the following internet address: http://www.wavecom.com Trademarks Some mentioned products are registered trademarks of their respective companies.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 1 General description 1.1 General information WISMO Quik Q2403 is a self-contained E-GSM/GPRS 900 / 1800 dual band module including the following features: • • • • • • • • • • • • • • • • • • 58.3 x 32.2 x 3.9 mm 2 Watts EGSM radio section running under 3.6 Volts 1 Watt GSM1800 radio section running under 3.6 Volts Digital section under 2.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 1.2 Functional description Power Supply G E N E R A L P U R P O S E C O N N E C T O R RF Interface RF I/O Controller Battery Management A/D Converter SIM Supply SIM Controller RF CPU FLASH SRAM Memory Management Unit C O N N E C T I O N F U N C T I O N S R.T.C GPSI Controller Audio Interface Vocoder Keyboard Controller UART Figure 1 : Functional architecture Page : 9 / 70 confidential © This document is the sole and exclusive property of WAVECOM.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 1.2.1 RF functionalities The RF functionalities comply with the Phase II EGSM 900/GSM 1800 recommendation.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2 Interfaces 2.1 General Purpose Connector (GPC) A 60 pins connector1 is provided to interface the WISMO Quik Q2403 Series with a board containing either a LCD module, or a keyboard, or a SIM connector, or a battery connection... The interfaces available on the GPC are described in the next paragraphs. ! Please be aware that some of these interfaces can not be handled when using the WISMO Quik Q2403 Series driven by AT commands: LCD interface, SPI bus.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.2 Power supply 2.2.1 Power supply description The power supply is one of the key issues in the design of a GSM terminal. Due to the burst mission in GSM / GPRS, the power supply must be able to deliver high current peaks in a short time. During these peaks the ripple (Uripp) and the drop (Udrop) on the supply voltage must not exceed a certain limit. In transmission mode, a GSM/GPRS class 2 terminal emits (1Tx) 577µs radio bursts every 4.615ms.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Power Supply Voltage VBATT VMIN VNOM VMAX Ripple max 3.3 V (*) 3.6 V 4.5 V (**) 50 mVpp for freq<200kHz 2 mVpp for freq>200kHz VDD 3.1 V 4.5 V 100 mVpp (*): This value has to be guaranted during the burst (with 2.0A Peak in GSM or GPRS mode) (**): max operating Voltage Stationnary Wave Ratio (VSWR) 2:1 When supplying the module with a battery, (battery+protections+PCB) should be <150 mOhms the total impedance 2.2.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 VDD Overall consumption During RX bursts Average communication 1Rx/1Tx@PCL5* Average communication 1Rx/1Tx@PCL8* Average communication GPRS only 2Rx/1Tx@PCL5* Average Idle mode (module in handset applications) Average Idle mode (module driven by AT commands, UART running) 50mA 265 mA 60mA 310 mA 190mA 210mA 275 mA 320 mA 2.3 mA 3 mA 12 mA 16 mA (*): PCL: Power Control Level. PCL5: 2W emission requested (max.power) PCL8: 0.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Power Supply Pinout Signal Pin number VBATT 55, 57, 58, 59 60 VDD 11 GND Shielding The grounding connection is done through the shielding " the four legs have to be soldered to the ground plane. 2.3 Electrical information for digital I/O All digital I/O comply with 3Volts CMOS. Operating conditions Parameter I/O type Min Max VIL CMOS -0.5 V 0.8 V VIH CMOS 2.1 V 3.0 V VOL 1X 0.2 V IOL = -1 mA 2X 0.2 V IOL = -2 mA 3X 0.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.4 LCD interface A AT T The WISMO Quik Q2403 Series can be connected to a LCD module driver through either a SPI bus or a two wires interface. 2.4.1 SPI bus The SPI bus includes a CLK signal, an IO signal and an EN signal complying with SPI bus standard. The maximum speed transfer is 3.25Mb/s. Pin description Signal Pin number I/O I/O type SPI_CLK 10 O 1X SPI_IO 8 I/O CMOS / 1X SPI_EN 28 O 1X Description SPI Serial Clock SPI Data SPI Enable 2.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.6 Keyboard interface ! Warning: This interface is not FULLY available with AT commands: An AT command allows to get the input key code (see +CMER command description). This code has then to be processed by the application. This interface provides 10 connections: 5 rows (R0 to R4) and 5 columns (C0 to C4). The scanning is a digital one , and the debouncing is done in the WISMO Quik Q2403 Series. No discrete components like R,C (Resistor, Capacitor) are needed.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Pin description Signal Pin number I/O I/O type Description CT103 / TX 39 I CMOS Transmit serial data CT104 / RX 32 O 1X CT105 / RTS 30 I CMOS CT106 / CTS 37 O 1X Clear To Send CT107 / DSR 36 O 1X Data Set Ready CT108-2 / DTR 34 I CMOS CT109 / DCD 51 O CMOS / 2X Data Carrier Detect CT125 / RI 54 O CMOS / 2X Ring Indicator CT102/GND Shielding legs Receive serial data Ready To Send Data Ready Terminal Ground The rising t
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 SIMCLK and SIMDATA to avoid any disturbance of the rising and falling edge. These types of diodes are mandatory for the Full Type Approval. They shall be placed as close as possible to the SIM socket. The following references can be used: DALC208SC6 from ST Microelectronics.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Note: When not used SIMPRES has to be tied to VCC. When used, a low to high transition means that the SIM card is inserted and a high to low transition means that the SIM card is removed. 2.8.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.9 General Purpose Input/Output The WISMO Quik Q2403 Series provides 6 General Purpose I/O, 3 General Purpose Outputs and 1 General Purpose Input. They are used to control any external device such as a LCD or a Keyboard backlight.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.10 Analog to Digital Converter Analog to Digital converter input is provided by the WISMO Quik Q2403 Series. This converter is a 10 bits one, ranging from 0 to 2.8V . Pin description Signal Pin number I/O I/O type Description AUXV0 33 I Analog A/D converter Electrical Characteristics Parameter Resolution Sampling rate Input signal range Max Unit 10 bits 90.3 Ksps 0 2.8V V ADC Reference Accuracy 0.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.11.1 Common microphone inputs characteristics The connection can be either differential or single-ended but using a differential connection in order to reject common mode noise and TDMA noise is strongly recommended. When using a single-ended connection, be sure to have a very good ground plane, a very good filtering as well as shielding in order to avoid any disturbance on the audio path.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.11.2 Common speaker outputs characteristics The connection can be differential or single-ended but using a differential connection to reject common mode noise and TDMA noise is strongly recommended. Morover in single-ended mode, ½ of the power is lost. When using a single-ended connection, be sure to have a very good ground plane, a very good filtering as well as shielding in order to avoid any disturbance on the audio path.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 The gain of SPK outputs is internally adjusted and can be tuned using an AT command. Speaker gain vs Max output voltage Receive Gain (dB) (*) Max output level (Vrms) AT+VGR (**) Max.speaker load (Ω) +2 1.74 0 to 15 150 0 1.38 16 to 31 50 -2 1.099 32 to 47 32 -4 0.873 48 to 63 32 -6 0.693 64 to 79 32 -8 0.551 80 to 95 32 -10 0.437 96 to 111 32 -12 0.347 112 to 127 32 -14 0.276 128 to 143 32 -16 0.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.11.3 Microphone inputs 2.11.3.1 Microphone 2 Inputs The MIC2 inputs are differential ones. They already include the convenient biasing for an electret microphone (0,5 mA and 2 Volts). This electret microphone can be directly connected on these inputs. The impedance of the microphone 2 has to be around 2kΩ. These inputs are the standard ones for an handset design while MIC1 inputs can be connected to an external headset or a handsfree kit.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.11.3.2 Microphone 1 Inputs The MIC1 inputs are differential and do not include internal bias. To use these inputs with an electret microphone, bias has to be generated outside the WISMO Quik Q2403 Series module according to the characteristic of this electret microphone. These inputs are the standard ones used for an external headset or a handsfree kit. AC coupling is already embedded in the module. 2.11.3.2.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.11.3.2.2 Single-ended connection Typical implementation: VAUDIO C3 R1 L2 C1 R2 C4 MIC1P L1 MIC1N C2 C5 Figure 7 : MIC1 inputs (single-ended connection) Note: VAUDIO must be very “clean” in single-ended connection (for example, VCC plus filter cell like RC or LC). R1 = from 100 to 330Ω R2 = usually between 1KΩ and 3.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.11.4 Speaker outputs 2.11.4.1 Speaker 2 Outputs Pin description Signal Pin # I/O I/O type Description SPK2P 45 O Analog Speaker 2 positive output SPK2N 47 O Analog Speaker 2 negative output 2.11.4.2 Speaker 1 Outputs Pin description Signal Pin # I/O I/O type Description SPK1P 41 O Analog Speaker 1 positive output SPK1N 43 O Analog Speaker 1 negative output 2.11.5 Buzzer Output The buzzer output is a digital one.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.12 Battery charging interface The WISMO Quik Q2403 Series module supports one battery charging circuit for Li-Ion batteries. This circuit uses an interface which consists of a current source inputs (CHG_IN) where the constant current has to flow in order to charge the battery. This current value depends on the battery capacity. It is recommended to provide a current equal to the value of the capacity plus 50mA. For a 550mA battery the current will be 600mA.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Internal Battery Resistor +VBATT Safety Circuitry VCC R1 BAT_TEMP C1 CTN GND Figure 9 : Connection examples 2.12.1 Li-ion charging procedure A constant current source has to be provided through CHG_IN input in order to charge the Li-ion battery, and BAT_TEMP input has to be connected to a battery temperature sensor. During this procedure the voltage of the battery is accurately monitored. The Li-ion charging involves two phases.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Calculation examples CTN(25°C) = 47K CTN(55°C) = 10K CTN(-10°C) = 300K CTN(-10°C) x VCC = ( CTN(-10°C) + R1 ) x BAT-TEMP (full range) R1= 47K " BAT-TEMP(-20°C) = 2.42V BAT-TEMP(55°C) = 0.49V R(-20°C) = R1//CTN(-10°C) = 40K R(+55°C) = 8K With C= 10nF:: RC(-20°C) = 400µs RC(+55°C) = 80µs 2.13 ON / ~OFF This input is used to switch ON or OFF the WISMO Quik Q2403 Series module. A high level signal has to be provided on the pin ON/~OFF to swith ON the module.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Operating conditions Parameter I/O type Min Max Unit VIL 0V 0.6 V V VIH 2.4 V VDD+0.5V V 2.13.1 Operating sequences 2.13.1.1 Power ON Once the module supplied, the application must set the ON/OFF signal to high to start the module power ON sequence. The ON/OFF signal must be hold for 500ms minimum. After this time, an internal mechanism keeps it on hold.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.13.1.2 Power OFF To properly power OFF the module, the application must set the ON/OFF signal to low and then send the AT+CPOF command to de-register from the network and switch off the module. Once the « OK » response is issued by the module, the power supply can be switched off.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Pin description Signal Pin number I/O I/O type Description BOOT 12 I CMOS Flash Loading Note: The nominal firmware download procedure is using the X-modem 2.15 Reset signal (~RST) This signal is used to force a reset procedure by providing low level during at least 100µs. This signal has to be considered as an emergency reset only. A reset procedure is already driven by an internal hardware during the power-up sequence.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Operating conditions Parameter Min Max *VT- 1.1V 1.2 V *VT+ 1.7V 1.9 V VOL Condition 0.4 V VOH IOL = -50 µA 2.0 V IOH = 50 µA * VT-, VT+ : Hysterisis Level Additional comments on RESET: The RESET process is activated either by the external ~RST signal OR by an internal signal (coming from a RESET generator). This automatic reset is activated at Power-up. The module remains in reset mode as long as the RST signal is held low.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.16 External Interrupt (~INTR) The WISMO Quik Q2403 Series provides an external interrupt input (not managed in the standard AT commands firmware). This input is very sensitive and an interrupt is activated on high to low edge. If this signal is not used it can be left open. If used this input has to be driven by an open collector or an open drain. This input is used for instance to power OFF automatically the module.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.18 VCC_RTC (Real Time Clock) 2.18.1 Interface description This pin is used as a back-up power supply for the internal Real Time Clock. The RTC is supported by the module when powered on but a back-up power supply is needed to save date and hour when the module is switched off. If the RTC is not used this pin can be left open.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.18.2.2 Super Capacitor Shottky Diode +VBATT Vin Vout En Gnd 470 1K VCC_RTC Ex : EECE0EL474S (Panasonic) Regulator 2.5 V ±10% (With very Low Iq) Estimated range with 0.47 Farad Gold Cap: 2 hours min. Note: the Gold Capacitor maximum voltage is 2.5 V. 2.18.2.3 Battery cell with regulator Shottky Diode +VBATT Vin Vout En Gnd 2K 1K VCC_RTC Regulator 2.5 V ±10% (With very Low Iq) Estimated range with 2 mAh battery rechargeable battery: ~3 days.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.18.2.4 Non Rechargeable battery This is the less recommended solution. Diode (Ex : BAS16) 10 VCC-RTC (2.75 V max) Ex : CR2016 (VARTA) Estimated range with 85 mAh battery: 4000 h minimum Note: The “non rechargeable battery” is always active, except when the module is ON. 2.19 RF interface The impedance is 50 0Ohms nominal and the DC impedance is 0 Ohm. 2.19.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Round pad Antenna pad Antenna pad Antenna connection by spring contact. Antenna connection by coaxial cable. Note: • The WISMO™ Quik Q2403 Series does not include an antenna switch for a car kit but this function can be implemented externally and it can be driven using a GPIO. • The antenna cable and connector should be chosen in order to minimize losses in the frequency bands used for GSM 900MHz and GSM1800MHz. • 0.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 CM2 CM4 CM3 CM1 Figure 15: WM2D-G900/G1800 antenna matching circuit (bottom view) Antenna pad GND CM3 CM2 ZL = 5 0 Ù CM1 GND CM4 Round pad GND Figure 16: Electrical diagram for the WM2D-G900/G1800 Page : 42 / 70 confidential © This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 2.19.2 RF performances RF performances are compliant with the ETSI recommendation 05.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 3 Technical specifications 3.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 26 GPO0 or SPI_AUX O 3X General Purpose Output or SPI Aux enable SIM 3V / 5V Keyboard Column SPI enable Keyboard Column RS232 interface Request To Send 27 28 29 30 COL2 SPI_EN COL3 CT105/RTS I/O O I/O I CMOS/1X 1X CMOS/1X CMOS 31 32 COL4 CT104/RX I/O O CMOS/1X 1X 33 AUXV0 I Analog 34 CT108-2/DTR I CMOS RS232 interface Data Terminal Ready 35 36 GPIO5 CT107/DSR I/O O CMOS / 2X 1X 37 CT106/CTS O 1X 38 BAT_TEMP I Analog 39 CT103/TX
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 51 52 53 54 55 56 57 58 59 60 GPIO3 or I/O CT109 / DCD O GPIO1 FLASH LED GPIO4 GPIO2 or I/O CMOS/2X I/O I/O CMOS/2X CMOS/2X RS232 – Data Carrier Detect General Purpose I/O Module State General Purpose I/O General Purpose I/O CT125 / RI O Supply Supply Supply Supply Supply Supply RS232 - Ring Indicator Battery Input RTC back-up supply Battery Input Battery Input Battery Input Battery Input +VBATT VCC_RTC +VBATT +VBATT +VBATT +VBATT I/O CMOS/2X G
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 3.2 Climatic and mechanical environments Conditions Temperature range Operating / Full GSM specifications compliant -20°C to +55°C Operating / functional -20°C to +70°C Storage -30°C to +85°C WISMO2D ENVIRONNEMENTAL CLASSES TYPE OF TEST STANDARDS STORAGE Class 1.2 TRANSPORTATION Class 2.3 Cold IEC 68-2.1 Ab test -25° C 72 h -40° C 72 h -20° C (GSM900) -10° C (GSM1800/1900) 16 h 16h Dry heat IEC 68-2.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 3.3 Mechanical specifications 3.3.1 Physical characteristics The WISMO Quik Q2403 Series module has a complete self-contained shield. • Dimensions : 58.3 x 32.2 x 3.9 mm external dimensions (except shielding pins) • Weight : <12 g 3.3.2 Mechanical drawings The next page gives the mechanical specifications of WISMO Quik Q2403 Series. Page : 48 / 70 confidential © This document is the sole and exclusive property of WAVECOM.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 4 Connectors references and peripheral devices 4.1 General Purpose Connector The GPC is a 60 pins connector with 0.5mm pitch from KYOCERA / AVX group with the following reference: 14 5087 060 930 861. The matting connector has the following reference: 24 5087 060 X00 8616. The stacking height is 3.0 mm. For further details see GPC data sheets in appendix. More information is also available from http://www.avxcorp.com 4.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 4.4 Microphone Possible suppliers: • HOSIDEN • PANASONIC 4.5 Speaker Possible suppliers: • SANYO • HOSIDEN • PRIMO • PHILIPS 4.6 Antenna Cable The following cable reference has been qualified for being mounted on WISMO Quik Q2403 Series: • RG178 4.7 GSM antenna GSM antennas and support for antenna adaptation can be obtained from manufacturers such as: • ALLGON (http://www.allgon.com ) • MOTECO (http://www.moteco.com ) • AMPHENOL (http://www.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 5 Design Guidelines The following paragraphs aims give design guidelines. 5.1 HARDWARE and RF 5.1.1 EMC recommendations The EMC tests have to be performed as soon as possible on the application to detect any possible problem.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 5.1.3 Layout requirement Page : 53 / 70 confidential © This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 5.1.4 Antenna Antenna sub-system and integration in the application is a major issue.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 5.3 Firmware upgrade The WISMO Quik Q2403 Series firmware is stored in flash memory and it can easily be upgraded. In order to follow the regular evolutions of the GPRS standard and to offer state of the art software, Wavecom recommends that the application designed around a WISMO (or WISMO based product) allows easy firmware upgrades on the module via the standard Xmodem protocol.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 6 Appendix 6.1 Wavecom acceptance test These tests are Wavecom internal qualification tests. They are performed on a Wavecom evaluation platform (module on test board). Applied standard Test Acceptance criteria for Full conformity to the recommendation regarding (and the main RF parameters. Performance Test ETSI recommendation GSM900/GSM1800 GSM900/GSM1900) communication.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 Electro Static IEC 1000-4-2. Discharge Test No performance degradation test. allowed after the Salt Mist Test IEC 68-2-11 After the test, visual inspection on the unit. Atmosphere Test Flowing mixed gas corrosion. IEC After the test, visual inspection on the unit and 68-2-60 inside. Marking Test EN 60 950 After the test, visual inspection on the unit. No degradation is allowed on the marking. 6.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 6.3 Safety recommendations (for information only) IMPORTANT FOR THE EFFICIENT AND SAFE OPERATION OF YOUR GSM APPLICATION BASED ON WISMO Quik Q2403 Series PLEASE READ THIS INFORMATION CAREFULLY 6.3.1 RF safety 6.3.1.1 General Your GSM terminal7 is based on the GSM standard for cellular technology. The GSM standard is spread all over the world. It covers Europe, Asia and some parts of America and Africa. This is the most used telecommunication standard.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 6.3.1.4 Antenna care and replacement Do not use the GSM terminal with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Replace a damaged antenna immediately. Consult your manual to see if you may change the antenna yourself. If so, use only a manufacturer-approved antenna. Otherwise, have your antenna repaired by a qualified technician. Use only the supplied or approved antenna.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 6.3.2.5 Aircraft Turn your terminal OFF before boarding any aircraft. • Use it on the ground only with crew permission. • Do not use it in the air. To prevent possible interference with aircraft systems, Federal Aviation Administration (FAA) regulations require you to have permission from a crew member to use your terminal while the aircraft is on the ground.
WM_PRJ_Q2400_PTS_001 - 003 6th November 2002 6.5 General Purpose Connector data sheet The next 6 pages are the KYOCERA/ELCO data sheets for the GPC (also available from http://www.avxcorp.com . Page : 64 / 70 confidential © This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
0,5 mm Spacing SERIES 5087 Surface Mount Vertical Plug Specifications: • 1000 per Tape and Reel • Voltage - 50 V • Current Rating - 0.4 A • Dielectric Withstanding Voltage - 500 V • Operating Temperature - (-25°C ~ +85°C) • Contact Material - phosphor bronze • Insulator Material - PPS (UL 94 V-0) MOUNTING LAYOUT No. of Pos. 20 30 36 40 50 60 10 10 10 10 10 10 5087 5087 5087 5087 5087 5087 P/N 020 XX0 030 XX0 036 XX0 040 XX0 050 XX0 060 XX0 861 861 861 861 861 861 A 4.5/.177 7.0/.276 8.5/.335 9.5/.
0,5 mm Spacing SERIES 5087 Surface Mount Vertical Receptacle Specifications: • 1000 per Tape and Reel • Voltage - 50 V • Current Rating - 0.4 A • Dielectric Withstanding Voltage - 500 V • Operating Temperature - (-25°C ~ +85°C) • Contact Material - phosphor bronze • Insulator Material - PPS (UL 94 V-0) MOUNTING LAYOUT No. of Pos. 20 30 36 40 50 60 20 20 20 20 20 20 5087 5087 5087 5087 5087 5087 P/N 020 030 036 040 050 060 x00 x00 x00 x00 x00 x00 861 861 861 861 861 861 A 4.5/.177 7.0/.276 8.5/.
0,5 mm Spacing PLUG RECE. PLUG RECE. PLUG RECE. No. of Pos. 20 30 36 40 50 60 10 20 10 20 10 20 P/N 5087 xxx x30 5087 xxx x00 5087 xxx x35 5087 xxx x00 5087 xxx x40 5087 xxx x00 Applications Stacking Height 861 861 861 861 861 861 3.0 3.5 4.0 A 7.2/.283 9.7/.382 11.2/.441 12.2/.480 14.7/.579 17.2/.
Super Micro Connectors 0.5mm Pitch Series 5087 Plug ORDERING CODE 14 5087 0XX X XX 8XX FINISH 861 = Ni Under Coated 1.25µm min. Gold-Mating Area Au 0.38µm min. 829 = Ni Under Coated 1.25µm min. Gold-Mating Area Au 0.1µm min. VARIATION 30 : H = 3.0mm 35 : H = 3.5mm 40 : H = 4.0mm TYPE 0 = without Boss with Retention Clip 2 = without Boss, Retention Clip 9 = without Boss, Retention Clip, with Adhesive Tape SERIES TAPE AND REEL 14 = Plug NUMBER OF POSITIONS (20, 30, 32, 36, 40, 50, 60) A = 0.
Super Micro Connectors 0.5mm Pitch Series 5087 Receptacle H = 3.0 ~ 4.0mm Type ORDERING CODE 24 5087 0XX X 00 8XX FINISH 861 = Ni Under Coated 1.25µm min. Gold-Mating Area Au 0.38µm min. 829 = Ni Under Coated 1.25µm min. Gold-Mating Area Au 0.1µm min. VARIATION H = 3.0 ~ 4.0mm TYPE 0 = without Boss with Retention Clip 2 = without Boss, Retention Clip 9 = without Boss, Retention Clip, with Adhesive Tape NUMBER OF POSITIONS SERIES (20, 30, 32, 36, 40, 50, 60) TAPE AND REEL 24 = Receptacle A = 0.
Super Micro Connectors 0.5mm Pitch Series 5087 Plug ORDERING CODE 14 5087 0XX X XX 8XX FINISH 861 = Ni Under Coated 1.25µm min. Gold-Mating Area Au 0.38µm min. 829 = Ni Under Coated 1.25µm min. Gold-Mating Area Au 0.1µm min. VARIATION 20 : H = 2.0mm 25 : H = 2.5mm TYPE 0 = without Boss with Retention Clip 2 = without Boss, Retention Clip 9 = without Boss, Retention Clip, with Adhesive Tape H = 2.0mm Type H = 2.5mm Type SERIES TAPE AND REEL 14 = Plug NUMBER OF POSITIONS (10*, 20, 30, 40, 50, 60) *2.
