WM_ Plug and Play Wireless CPU® FASTRACK M1306B User Guide Revision: 003 Date: November 2006
Plug and Play Wireless CPU® FASTRACK M1306B User Guide Reference: WM_PRJ_M13_UGD_001 Revision: 003 Date: November 11, 2006 Supports Open AT® embedded ANSI C applications confidential © Page: 1 / 65 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement.
Fastrack M1306B User Guide Document History Revision Date 001 15 Jul 04 002 003 5 11 th th April 05 November, 06 List of revisions First Issue Document update Document update: • Update of “Environmental characteristics” chapter • Integration of RoHS & WEE • Document Format & naming changes • Other minor updates concerning: fuse, voltage drop in cable etc. confidential © Page: 2 / 65 This document is the sole and exclusive property of WAVECOM.
Fastrack M1306B User Guide Overview The Fastrack M1306B is a discrete, rugged cellular Plug & Play Wireless CPU® offering state-of-the-art GSM/GPRS connectivity for machine to machine applications. Proven for reliable, stable performance on wireless networks worldwide, Wavecom’s latest generation of Fastracks -M1306B- continues to deliver rapid time to market and painless integration.
Fastrack M1306B User Guide Disposing of the product This electronic product is subject to the EU Directive 2002/96/EC for Waste Electrical and Electronic Equipment (WEEE). As such, this product must not be disposed off at a municipal waste collection point. Please refer to local regulations for directions on how to dispose off this product in an environmental friendly manner. confidential © Page: 4 / 65 This document is the sole and exclusive property of WAVECOM.
Fastrack M1306B User Guide Cautions Information furnished herein by WAVECOM is accurate and reliable. However, no responsibility is assumed for its use. Please read carefully the safety recommendations given in Chapter 9 for an application based on Fastrack M1306B. Trademarks ®, WAVECOM®, Wireless CPU®, Open AT® and certain other trademarks and logos appearing on this document, are filed or registered trademarks of Wavecom S.A. in France or in other countries.
Fastrack M1306B User Guide Web Site Support General information about Wavecom and its range of products: www.wavecom.com Specific support is available for the Fastrack M1306B Plug & Play Wireless CPU®: www.wavecom.com/M1306B Carrier/Operator approvals: www.wavecom.com/approvals ® Open AT Introduction: www.wavecom.com/OpenAT Developer support for software and hardware: www.wavecom.com/forum confidential © Page: 6 / 65 This document is the sole and exclusive property of WAVECOM.
Fastrack M1306B User Guide Contents DOCUMENT HISTORY ...............................................................................................2 OVERVIEW ................................................................................................................3 CAUTIONS ................................................................................................................5 TRADEMARKS ........................................................................................................
Fastrack M1306B User Guide 3.2.1.1 Antenna Connector ........................................................................... 21 3.2.1.2 Power Supply Connector .................................................................. 21 3.2.1.3 Sub HD 15-pin Connector ................................................................. 22 3.2.2 Power supply cable................................................................................. 24 4 BASIC FEATURES AND SERVICES ......................................
Fastrack M1306B User Guide 7.6.1 7.6.2 General presentation............................................................................... 45 Reset Sequence ...................................................................................... 46 7.7 Audio.............................................................................................................. 46 7.7.1 Microphone Inputs.................................................................................. 46 7.7.2 Speaker Outputs .........
Fastrack M1306B User Guide List of Figures Figure 1: Complete package contents ....................................................................... 16 Figure 2: Packaging box ........................................................................................... 17 Figure 3: Production sticker ...................................................................................... 18 Figure 4: Fastrack M1306B general description ........................................................
Fastrack M1306B User Guide List of Tables . Table 1: Power supply connector pin description ..................................................... 22 Table 2: Sub HD 15-pin connector description ......................................................... 23 Table 3: Basic features of the M1306B ..................................................................... 25 Table 4: M1306B operational status.........................................................................
Fastrack M1306B User Guide References 1 References 1.1 Reference Documents For more details, several reference documents may be consulted. The Wavecom reference documents are provided in the Wavecom documents package contrary to the general reference documents, which are not Wavecom owned. 1.1.1 Open AT® Software Documentation [1] Getting started with Open AT® (Ref.WM_ASW_OAT_CTI_001) [2] Open AT® Tutorial (Ref.WM_ASW_OAT_UGD_001) [3] Tools Manual (Ref.
Fastrack M1306B User Guide References 1.
Fastrack M1306B User Guide References Abbreviation Definition GND GrouND GPIO General Purpose Input Output GPRS General Packet Radio Service GSM Global System for Mobile communications HR Half Rate I Input IEC International Electrotechnical Commission IMEI International Mobile Equipment Identification I/O Input / Output LED Light Emitting Diode MAX MAXimum ME Mobile Equipment MIC MICrophone Micro-Fit Family of connectors from Molex MIN MINimum MNP Microcom Networking Protocol
Fastrack M1306B User Guide References Abbreviation Definition RTS Request To Send RX Receive SIM Subscriber Identification Module SMA SubMiniature version A RF connector SMS Short Message Service SNR Signal-to-Noise Ratio SPL Sound Pressure Level SPK SpeaKer SRAM Static RAM TCP/IP Transmission Control Protocol / Internet Protocol TDMA Time Division Multiple Access TU Typical Urban fading profile TUHigh Typical Urban, High speed fading profile TX Transmit TYP TYPical VSWR Volt
Fastrack M1306B User Guide Packaging 2 Packaging 2.1 Contents The complete package contents of the Fastrack M1306B consists of (see Figure 1): • one packaging box (A), • one M1306B (B), • two holding bridles (C), • one power supply cable with fuse integrated (D) • a short notice (E) with: a summary of the main technical features, safety recommendations, EC declaration of conformity.
Fastrack M1306B User Guide Packaging 2.2 Packaging Box The packaging box is a carton box (see Figure 2) with the following external dimensions: • width: 54.5 mm, • height: 68 mm, • length: 108 mm.
Fastrack M1306B User Guide Packaging 2.3 Production Sticker A production sticker (see Figure 3) located at the M1306B back side gives the following information: • product reference (M1306B), • part number (WMxxxxx), • CE marking (CE0536), • 15-digit IMEI code, • RoHS logo, • WEEE logo. Figure 3: Production sticker confidential © Page: 18 / 65 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement.
Fastrack M1306B User Guide General Presentation 3 General Presentation 3.1 Description The Fastrack M1306B description is given in the Figure 4 below. Micro-Fit connector Sub HD connector Front cap SMA connector Back cap Extractible SIM card holder BACK CAP LED SIM card holder ejector Figure 4: Fastrack M1306B general description confidential © Page: 19 / 65 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement.
Fastrack M1306B User Guide General Presentation In addition, two holding bridles are provided to tighten the M1306B on a support. Holding bridles Figure 5: Fastrack M1306B holding bridles confidential © Page: 20 / 65 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement.
Fastrack M1306B User Guide General Presentation 3.2 External Connections 3.2.1 Connectors 3.2.1.1 Antenna Connector The antenna connector is a SMA type connector for a 50 Ω RF connection. SMA connector for antenna connection Figure 6: SMA connector for antenna connection 3.2.1.2 Power Supply Connector The power supply connector is a 4-pin Micro FIT connector for: • external DC Power Supply connection, • GPIOs connection (two General Purpose Input/Output signals available).
Fastrack M1306B User Guide General Presentation Table 1: Power supply connector pin description Pin # Signal I/O I/O type Description Comment 1 V+BATTERY I Power supply Battery voltage input: 5.5 V Min. High current 13.2 V Typ. 32 V Max. 2 GND 3 GPIO4 4 GPIO5 Power supply Ground I/O CMOS/2X General Purpose Input/output I/O CMOS/2X General Purpose Input/output Warning: Both pin 3 and pin 4 are used by GPIO interface.
Fastrack M1306B User Guide General Presentation Table 2: Sub HD 15-pin connector description Pin # Signal (CCITT / EIA) I/O I/O type Description 1 CDCD/CT109 O STANDARD RS232 Data Carrier Detect RS232 2 CTXD/CT103 I STANDARD RS232 RS232 Transmit serial data 3 BOOT I CMOS Boot 4 CMIC2P I Analog Microphone positive line 5 CMIC2N I Analog Microphone negative line 6 CRXD/CT104 O STANDARD RS232 Receive serial data RS232 7 CDSR/CT107 O STANDARD RS232 8 CDTR/CT108-2 I STAN
Fastrack M1306B User Guide General Presentation 3.2.2 Power supply cable Connector Molex Micro - Fit 3. 0 Black wire Stripped wire tinned over 5 mm (GND) Connector Side View Red wire (+) GPIO 5 Fuse 800 mA / 250 V ( 5 x 20 mm ) GPIO 4 Figure 9: Power supply cable Component Micro-Fit 4-pin Characteristics connector Part number: MOLEX 43025-0400 Cable Cable length: ∼1.5 m Wire Core: tinned copper 24 x 0.2 mm Section: 0.
Fastrack M1306B User Guide Basic Features and Services 4 Basic Features and Services Basic features of the M1306B and available services are summarized in the table below. Table 3: Basic features of the M1306B Features Open AT ® GSM DCS ® Open AT programmable: Native execution of embedded standard ANSI C applications, Custom AT command creation, Custom application library creation, Standalone operation. Standard 900 MHz. 1800 MHz E-GSM compliant. GPRS Output power: class 4 (2W).
Fastrack M1306B User Guide Basic Features and Services Features Data GSM DCS Data circuit asynchronous. Transparent and Non Transparent modes. Up to 14.400 bits/s. MNP Class 2 error correction. V42.bis data compression. Fax Automatic fax group 3 (class 1 and Class 2). Audio Echo cancellation Noise reduction Telephony. Emergency calls. Full Rate, Enhanced Full Rate and Half Rate operation (FR/EFR/HR). Dual Tone Multi Frequency function (DTMF). GSM Call forwarding. supplement Call barring.
Fastrack M1306B User Guide Using the M1306B Wireless CPU® 5 Using the M1306B Wireless CPU® 5.1 Getting Started 5.1.1 Mount the M1306B To mount the M1306B on its support, bind it using the holding bridles as shown in the Figure 10 below. Figure 10: M1306B mounting For the drill template, refer to Figure 16. 5.1.2 Set up the M1306B To set up the M1306B, perform the following operations: • Press SIM card holder ejector with a sharp object (for example, the tip of a pen).
Fastrack M1306B User Guide Using the M1306B Wireless CPU® Note: For automotive application, it is recommended to connect the V+BATTERY line of the M1306B directly to the battery positive terminal. • Plug the power supply cable into the M1306B and switch on the external power supply source. • The M1306B is ready to work. Refer to section 5.8 for the description of AT commands used to configure the M1306B. 5.1.
Fastrack M1306B User Guide Using the M1306B Wireless CPU® 5.1.4 Reset the M1306B To reset the M1306B, a hardware reset signal is available on pin 14 of the Sub HD 15-pin connector (RESET). The M1306B reset is carried out when this pin is low for at least 500 µs. Warning This signal has to be considered as an emergency reset only. For further details on the M1306B reset, refer to section 7.6. 5.
Fastrack M1306B User Guide Using the M1306B Wireless CPU® M 1306B Figure 11: Recommended power supply connection on trucks Figure 11 gives the recommended power supply connection where the ground connection of the M1306B is not directly connected to the battery but is connected after the Circuit Breaker (on the truck ground or the fuse box). 5.2.2 Technical Constraints on Trucks It is highly not recommended to connect directly the power supply on the battery rather than on the circuit breaker.
Fastrack M1306B User Guide Using the M1306B Wireless CPU® M1306B Figure 12: Example of electrical connection which may dramatically damage the M1306B Figure 12 gives an example of electrical connection which may dramatically damage the M1306B when its ground connection is directly connected to the battery ground. In this example, when the circuit breaker is switched OFF, the current flows through the M1306B and powers the electrical circuit of the truck (for example, dashboard).
Fastrack M1306B User Guide Using the M1306B Wireless CPU® Table 4: M1306B operational status LED Status ON LED light activity M1306B status LED ON permanent M1306B is switched ON but not registered on the network OFF LED Flashing slowly M1306B is switched ON and registered on the network, but no communication is in progress (Idle mode) LED Flashing rapidly M1306B is switched ON and registered on the network, and a communication is in progress LED OFF M1306B is switched OFF. 5.
Fastrack M1306B User Guide Using the M1306B Wireless CPU® 5.5 Verify the Received Signal Strength The Fastrack M1306B establishes a call only if the received signal is sufficiently strong. To verify the received signal strength, do the following operations: • • Using a communication software such as Hyperterminal, enter the AT command AT+CSQ. The response returned has the following format: +CSQ: , with: • = received signal strength indication, • = channel bit error rate.
Fastrack M1306B User Guide Using the M1306B Wireless CPU® 5.7 Verify the M1306B Network Registration 1. Make sure a valid SIM card has been previously inserted in the M1306B SIM card holder. 2. Using a communication software such as a Hyperterminal, enter the following AT commands: a. AT+CPIN=xxxx to enter PIN code xxxx. b. AT+CREG?. To ascertain the registration status.
Fastrack M1306B User Guide Using the M1306B Wireless CPU® 5.8 Main AT Commands for the Wireless CPU® The table below lists the main AT commands required for starting the Wireless CPU®. For other AT commands available or further information on the AT commands, refer to "AT Commands Interface Guide" [7]. Table 8: Main usual AT commands for the Wireless CPU® Description Enter PIN Code Network registration checking AT commands Wireless CPU® response Comment AT+CPIN=xxxx OK PIN Code accepted.
Fastrack M1306B User Guide Using the M1306B Wireless CPU® Description AT commands Wireless CPU® response Hang up ATH OK Store the parameters in EEPROM AT&W OK Comment The configuration settings are stored in EEPROM. (1*) The command "AT+CMEE=1" switch to a mode enabling more complete error diagnostics. 5.9 Firmware Upgrade Procedure The firmware upgrade procedure is used to update the firmware embedded into the Fastrack M1306B.
Fastrack M1306B User Guide Troubleshooting 6 Troubleshooting This section of the document describes possible problems encountered when using the Fastrack M1306B and their solutions. To review other troubleshooting information, refer the ‘FAQs’ (Frequently Asked Questions) page at www.wavecom.com or use the following link: http://www.wavecom.com/support/faqs.php 6.
Fastrack M1306B User Guide Troubleshooting 6.2 Receiving "ERROR" Message The M1306B returns an "ERROR" message (in reply to an AT command) in the following cases: • AT command syntax is incorrect: check the command syntax (refer to "AT Commands Interface Guide" [7]), • AT command syntax is correct, but transmitted with wrong parameters: • Enter the AT+CMEE=1 command in order to change the error report method to the verbose method, which includes the error codes.
Fastrack M1306B User Guide Troubleshooting Table 10: Solutions for "NO CARRIER" message If the M1306B returns… "NO CARRIER" Then ask… Action… Is the received signal strong enough? Refer to section 5.5 to verify the strength of the received signal. Is the M1306B registered on the network? Refer to section 5.7 to verify the registration. Is the antenna properly connected? Refer to section 8.2.6.3 for antenna requirements.
Fastrack M1306B User Guide Troubleshooting Table 11: Interpretation of extended error code Error Code 1 Diagnostic Hint Unallocated phone number 16 Normal call clearing 17 User busy 18 No user responding 19 User alerting, no answer 21 Call rejected 22 Number changed 31 Normal, unspecified 50 Requested facility not subscribed Check your subscription (data subscription available?). 68 ACM equal or greater than ACMmax Credit of your pre-paid SIM card expired.
Fastrack M1306B User Guide Functional Description 7 Functional Description 7.
Fastrack M1306B User Guide Functional Description 7.2 Power Supply 7.2.1 General Presentation The M1306B is supplied by an external DC voltage (V+BATTERY) from +5.5 V to +32 V at 2.2 A. Main regulation is made with an internal DC/DC converter in order to supply all the internal functions with a DC voltage. Correct operation of the Fastrack M1306B in communication mode is not guaranteed if input voltage (V+BATTERY) falls below 5.5 V. Note: The minimum input voltage specified here is at the M1306B input.
Fastrack M1306B User Guide Functional Description • Data Terminal Ready (CT108-2/DTR), • Data Set Ready (CT107/DSR), • Data Carrier Detect (CT109/DCD), • Ring Indicator (CT125/RI). CT103 / TX CT104 / RX FASTRACK M1306B CT105 / RTS CT106 / CTS DTE CT107 / DSR (DCE) CT108-2 / DTR CT109 / DCD CT125 / RI Figure 14: RS232 Serial Link signals RS232 interface has been designed to allow flexibility in the use of the serial interface signals.
Fastrack M1306B User Guide Functional Description 7.3.
Fastrack M1306B User Guide Functional Description • See Table 20 in section 8.2.3 for I/O type 2X definition. 7.5 BOOT This signal must not be connected. It’s use is strictly reserved to Wavecom or competent retailers. 7.6 RESET 7.6.1 General presentation This signal is used to force a reset procedure by providing low level during at least 500 µs. This signal must be considered as an emergency reset only. A reset procedure is automatically driven by an internal hardware during the power-up sequence.
Fastrack M1306B User Guide Functional Description 7.6.2 Reset Sequence To activate the "emergency" reset sequence, the RESET signal has to be set to low for 500 µs minimum. As soon as the reset is done, the AT interface answers "OK" to the application. For this, the application must send AT↵. If the application manages hardware flow control, the AT command may be sent during the initialization phase. Another solution is to use the AT+WIND command to get an unsolicited status from the M1306B.
Fastrack M1306B User Guide Functional Description This electret microphone may be directly connected to these inputs allowing an easy connection to a handset. The microphone impedance must be around 2 kΩ. AC coupling is already embedded in the Wireless CPU®. The gain of the microphone inputs is internally adjusted and may be tuned from 30 dB to 51 dB using an AT +VGT command (refer to AT commands documentation [7]).
Fastrack M1306B User Guide Technical Characteristics 8 Technical Characteristics 8.1 Mechanical Characteristics Table 12: Mechanical characteristics Dimensions Overall Dimension Weight 73 x 54.5 x 25.5 mm (excluding connectors) 88 x 54.5 x 25.5 mm ≈ 80 grams (M1306B only) < 120 grams (M1306B + bridles + power supply cable) Volume 101.
Fastrack M1306B User Guide Technical Characteristics Figure 16: Dimensioning diagram confidential © Page: 49 / 65 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement.
Fastrack M1306B User Guide Technical Characteristics 8.2 Electrical Characteristics 8.2.1 Power Supply Table 13: Electrical characteristics Operating Voltage ranges 5.5 V to 32 V DC (GSM or DCS or GPRS). Maximum current 480 mA Average at 5.5V. 2.1 A Peak at 5.5 V. Note: The M1306B is permanently powered once the power supply is connected. The following table describes the consequences of over-voltage and under-voltage with the Fastrack M1306B.
Fastrack M1306B User Guide Technical Characteristics Table 15: Power consumption (1*) Power Consumption in E-GSM 900/DCS 1800 MHz - GPRS class 10 E-GSM 900 DCS 1800 @ 5.5 V 2.1 A 1,88 A @ 13,2 V 1.4 A 1.1 A @ 32 V 610 mA 390 mA @ 5.5 V 500 mA 390 mA @ 13,2 V 500 mA 160 mA Average 3Rx/2Tx @Pcl0 @ 32 V 95 mA 80 mA Input Peak Supply Current Power = 33,10 dBm GSM 900 During 1TX bursts @Pcl5 Power = 30,00 dBm GSM 1800 @ 5.5 V 2.1 A mA 1,88 A @ 13,2 V 1.4 A 1.
Fastrack M1306B User Guide Technical Characteristics 8.2.2 Audio Interface The audio interface is available through the Sub HD 15-pin connector. Table 16: Audio parameters caracteristics Audio parameters Min Typ 0.
Fastrack M1306B User Guide Technical Characteristics Table 19: Recommended characteristics for the speaker: Feature Value Type 10 mW, electro-magnetic Impedance Z = 32 to 50 Ω Sensitivity 110 dB SPL min. (0 dB = 20 µPa) Frequency response compatible with the GSM specifications 8.2.3 General Purpose Input/Output Both GPIO4 and GPIO5 may be interfaced with a component that comply with 3 Volts CMOS levels. Table 20: Operating conditions Parameter I/O type Min Max Condition VIL CMOS -0.5 V 0.
Fastrack M1306B User Guide Technical Characteristics Table 23: Operating conditions Parameter Min Max Condition *VT- 1.1 V 1.2 V *VT+ 1.7 V 1.9 V VOL 0 0.4 V IOL = -50 µA VOH 2.0 V 2.8 V IOH = 50 µA * VT-, VT+ :Hysteresis thresholds 8.2.6 RF Characteristics 8.2.6.
Fastrack M1306B User Guide Technical Characteristics 8.2.6.2 RF Performances RF performances are compliant with the ETSI recommendation GSM 05.05. The RF performances for receiver and transmitter are given in the table below.
Fastrack M1306B User Guide Technical Characteristics 8.2.6.3 External Antenna The external antenna is connected to the M1306B via the SMA connector. The external antenna must fulfill the characteristics listed in the table below. Table 26: External antenna characteristics Antenna frequency range Dual-band GSM 900/DCS 1800 MHz Impedance 50 Ohms nominal DC impedance 0 Ohm Gain (antenna + cable) 0 dBi VSWR (antenna + cable) 2 Note: Refer to Chapter 10 for recommended antenna. 8.
Fastrack M1306B User Guide Technical Characteristics Table 28: Environmental standard constraints Environmental Tests Environmental Classes (IEC TR 60721-4) (IEC 60721-3) Storage Tests Standards (IEC 607213-1) Class IE13 Operation Transportation (IEC 60721-3-2) Class IE23 Stationary (IEC 60721-33) Class IE35 Non-Stationary (IEC 60721-3-7) Class IE73 Cold IEC 60068-2-1 : Ab/Ad -25°C, 16 h -40°C, 16 h -5°C, 16 h -5°C, 16 h Dry heat IEC 60068-2-2 : Bb/Bd +70°C, 16 h +70°C, 16 h +55°C, 16 h
Fastrack M1306B User Guide Technical Characteristics Notes: Short description of Class IE13 (For more information see standard IEC 60721-3-1) "Locations without controlled temperature and humidity, where heating may be used to raise low temperatures, locations in buildings providing minimal protection against daily variations of external climate, prone to receiving rainfall from carrying wind".
Fastrack M1306B User Guide Technical Characteristics Lubrication of the SIM card had been tested by Wavecom (using Tutela Fluid 43EM from MOLYDUVAL) and gives very good results. If waterproof enclosure with a desiccant solution is used, check with your desiccant retailer the quantity that must be used according to the enclosure dimensions. Ensure humidity has been removed before sealing the enclosure. Any solution selected must be qualified by the customer on the final application.
Fastrack M1306B User Guide Technical Characteristics 8.5.3 ESD The M1306B withstands ESD according to IEC 1000-4-2 requirements for all accessible parts of the M1306B except the RF part: • 8 kV of air discharge, • 4 kV of contact discharge. 8.5.4 Miscellaneous Filtering guarantees: • EMI/RFI protection in input and output, • Signal smoothing. confidential © Page: 60 / 65 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement.
Fastrack M1306B User Guide Safety recommendations 9 Safety recommendations 9.1 General Safety It is important to follow any special regulations regarding the use of radio equipment due in particular to the possibility of radio frequency (RF) interference. Please follow the safety advice given below carefully. Switch OFF your Wireless CPU®: • When in an aircraft. The use of cellular telephones in an aircraft may endanger the operation of the aircraft, disrupt the cellular network and is illegal.
Fastrack M1306B User Guide Safety recommendations The Wireless CPU® is not designed for and intended to be used in portable applications (within 20 cm or 8 inches of the body of the user) and such uses are strictly prohibited. 9.2 Vehicle Safety Do not use your Wireless CPU® while driving, unless equipped with a correctly installed vehicle kit allowing ’Hands-Free’ Operation. Respect national regulations on the use of cellular telephones in vehicles. Road safety always comes first.
Fastrack M1306B User Guide Safety recommendations 9.4 Your Responsibility This Wireless CPU® is under your responsibility. Please treat it with care respecting all local regulations. It is not a toy. Therefore, keep it in a safe place at all times and out of the reach of children. Try to remember your Unlock and PIN codes. Become familiar with and use the security features to block unauthorized use and theft. confidential © Page: 63 / 65 This document is the sole and exclusive property of WAVECOM.
Fastrack M1306B User Guide Recommended Accessories 10 Recommended Accessories Accessories recommended by Wavecom for the Fastrack M1306B are given in the table below. Table 29: List of recommended accessories Designation Part number Dual-band antenna SMA/FME adaptor 1140.
Fastrack M1306B User Guide Online Support 11 Online Support Wavecom provides an extensive range on online support which includes the following areas of Wavecom’s wireless expertise: • the latest version of this document • new versions of our Operating System user guides • comprehensive support for Open AT® • regulatory certifications • carrier certifications • application notes To gain access to this support, simply visit our web site at www.wavecom.com and click on "Support".
WAVECOM S.A. - 3 esplanade du Foncet - 92442 Issy-les-Moulineaux Cedex - France - Tel: +33(0)1 46 29 08 00 - Fax: +33(0)1 46 29 08 08 Wavecom, Inc. - 4810 Eastgate Mall - Second Floor - San Diego, CA 92121 - USA - Tel: +1 858 362 0101 - Fax: +1 858 558 5485 WAVECOM Asia Pacific Ltd. - Unit 201-207, 2nd Floor, Bio-Informatics Centre – No.
