User Manual

ManualsBrandsWave Wireless Networking ManualsElectronicsPoint to Point Spread Spectrum Transceiver

100

SC5800 User Manual

Object ID Group Object Type Access Description

undeclared, unused messages).

1.3.6.1.4.1.1316.1.1.1.3.1.3 mdrmteOutdoorUnitResetType INTEGER read-only This message is read from the

Outdoor Unit and identifies the

last reason for a reset within the

OU.

1.3.6.1.4.1.1316.1.1.1.3.1.4 mdrmteOutdoorUnitLockDetect INTEGER read-only The transmit RF synthesizer,

receive RF synthesizer and IF

phased locked loop lock detect

signals are monitored and

reported via this MIB element.

1.3.6.1.4.1.1316.1.1.1.3.2 mdrmteSelfTest

1.3.6.1.4.1.1316.1.1.1.3.2.1 mdrmteFlash INTEGER read-only Identifies pass/fail status of the

Indoor Unit's application flash.

1.3.6.1.4.1.1316.1.1.1.3.2.2 mdrmteDRAM INTEGER read-only Identifies pass/fail status of the

Indoor Unit's Dynamic RAM.

1.3.6.1.4.1.1316.1.1.1.3.2.3 mdrmteSRAM INTEGER read-only Identifies pass/fail status of the

Indoor Unit's Static RAM.

1.3.6.1.4.1.1316.1.1.1.3.2.4 mdrmteLineInterface INTEGER read-only Identifies pass/fail status of the

Indoor Unit's Line Interface IC.

1.3.6.1.4.1.1316.1.1.1.3.2.5 mdrmteFPGA INTEGER read-only Identifies pass/fail status of the

Indoor Unit's FPGA interface

registers to the microprocessor.

1.3.6.1.4.1.1316.1.1.1.3.2.6 mdrmteFEC INTEGER read-only Identifies pass/fail status of the

Indoor Unit's FEC IC electrical

interface.

1.3.6.1.4.1.1316.1.1.1.3.2.7 mdrmteRealTimeClock INTEGER read-only Identifies pass/fail status of the

Indoor Unit's Real Time Clock.

1.3.6.1.4.1.1316.1.1.1.3.2.8 mdrmteIndoorUnitResetType INTEGER read-only This message is read from the

Indoor Unit and identifies the

last reason for a reset within the

IU.

1.3.6.1.4.1.1316.1.1.1.3.2.9 mdrmteLoopbackMode INTEGER read-write Entry defines the loopback

mode of a radio station in terms

of loopback at either the

payload line interface level,

baseband processor level in an

OU or RF loopback in the OU.

1.3.6.1.4.1.1316.1.1.1.3.2.10 mdrmteLoopbackTimeOut INTEGER read-write This is the number of seconds

the loopback will run for until it

times out.

1.3.6.1.4.1.1316.1.1.1.3.3 mdrmteTrapManagement

1.3.6.1.4.1.1316.1.1.1.3.3.1 mdrmteTrapFilter INTEGER read-write Alarms within the MDR product

are classified as critical, major,

minor or informational. The trap

filter allows screening of alarms

before they are dispatched as

traps.

1.3.6.1.4.1.1316.1.1.1.3.3.2 mdrmteNumberTrapManagers INTEGER read-only This entry shows the number of

trap managers allowed.

1.3.6.1.4.1.1316.1.1.1.3.3.3 mdrmteTrapManagerTable SEQUENCE

1.3.6.1.4.1.1316.1.1.1.3.3.3.1 mdrmteTrapManagerEntry SYNTAX

1.3.6.1.4.1.1316.1.1.1.3.3.3.1.

mdrmteTrapManagerIndex INTEGER

1.3.6.1.4.1.1316.1.1.1.3.3.3.1.

mdrmteTrapManagerIP IpAddress read-write This is the IP address of the

management station that is set

up to detect and act upon